Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - transceivers RS485 1/1 SOIC 8

V upto70V

FAULT

M0092-02

SN65HVD1780

SN65HVD1781

SN65HVD1782

www.ti.com

SLLS877F –DECEMBER 2007–REVISED FEBRUARY 2010

Fault-Protected RS-485 Transceivers with 3.3-V to 5-V Operation

Check for Samples: SN65HVD1780, SN65HVD1781, SN65HVD1782

FEATURES

These devices combine a differential driver and a

• Bus-Pin Fault Protection to:

differential receiver, which operate from a single

– > ±70 V ('HVD1780, 81)

power supply. In the 'HVD1782, the driver differential

– > ±30 V ('HVD1782)

outputs and the receiver differential inputs are

connected internally to form a bus port suitable for

• Operation With 3.3-V to 5-V Supply Range

half-duplex (two-wire bus) communication. This port

• ±16 kV HBM Protection on Bus Pins

features a wide common-mode voltage range, making

• Reduced Unit Load for up to 320 Nodes

the devices suitable for multipoint applications over

• Failsafe Receiver for Open-Circuit,

long cable runs. These devices are characterized

from –40°C to 125°C. These devices are

Short-Circuit and Idle-Bus Conditions

pin-compatible with the industry-standard SN75176

• Low Power Consumption

transceiver, making them drop-in upgrades in most

– Low Standby Supply Current, 1 mA Max

systems.

– I

4 mA Quiescent During Operation

These devices are fully compliant with ANSI TIA/EIA

• Pin-Compatible With Industry-Standard

485-A with a 5-V supply and can operate with a 3.3-V

SN75176

supply with reduced driver output voltage for

low-power applications. For applications where

• Signaling Rates of 115 kbps, 1 Mbps, and up

operation is required over an extended

to 10 Mbps

common-mode voltage range, see the

SN65HVD1785 (SLLS872) data sheet.

APPLICATIONS

• HVAC Networks

• Security Electronics

• Building Automation

• Telecomm Equipment

• Motion Control

• Industrial Networks

DESCRIPTION

These devices are designed to survive overvoltage

faults such as direct shorts to power supplies,

mis-wiring faults, connector failures, cable crushes,

and tool mis-applications. They are also robust to

ESD events, with high levels of protection to the

human-body-model specification.

Transceiver Signaling Rate Number of Nodes

HVD1780 Up to 115 kbps Up to 320

HVD1781 Up to 1 Mbps Up to 320

HVD1782 Up to 10 Mbps Up to 64

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (21 pages)

PAGE 1
SN65HVD1780 SN65HVD1781 SN65HVD1782 www.ti.com SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 Fault-Protected RS-485 Transceivers with 3.3-V to 5-V Operation Check for Samples: SN65HVD1780, SN65HVD1781, SN65HVD1782 FEATURES 1 • • • • • • • • Bus-Pin Fault Protection to: – > ±70 V ('HVD1780, 81) – > ±30 V ('HVD1782) Operation With 3.
PAGE 2
SN65HVD1780 SN65HVD1781 SN65HVD1782 SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
PAGE 3
SN65HVD1780 SN65HVD1781 SN65HVD1782 www.ti.com SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 ABSOLUTE MAXIMUM RATINGS (1) VCC Voltage range at bus pins 'HVD1780, 81 A, B pins 'HVD1782 A, B pins UNIT V –70 to 70 V –70 to 30 V –0.3 to VCC + 0.3 V Transient overvoltage pulse through 100 Ω per TIA-485 –70 to 70 V Receiver output current –24 to 24 mA 170 °C Input voltage range at any logic pin TJ VALUE –0.
PAGE 4
SN65HVD1780 SN65HVD1781 SN65HVD1782 SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 www.ti.com ELECTRICAL CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER |VOD| Driver differential output voltage magnitude TEST CONDITIONS MIN RL = 60 Ω, 4.75 V ≤ VCC 375 Ω on each output to –7 V to 12 V Figure 1 TA < 85°C 1.5 TA < 125°C 1.4 RL = 54 Ω, 4.75 V ≤ VCC ≤ 5.25 V TA < 85°C 1.7 TA < 125°C 1.5 RL = 54 Ω, 3.15 V ≤ VCC ≤ 3.45 V TA < 85°C RL = 100 Ω, 4.
PAGE 5
SN65HVD1780 SN65HVD1781 SN65HVD1782 www.ti.com SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 SWITCHING CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 3.15 V < VCC < 3.45 V 0.4 1.4 1.8 ms 3.15 V < VCC < 5.5 V 0.4 1.7 2.6 µs 0.8 2 ms 20 250 ns 0.1 5 ms 0.
PAGE 6
SN65HVD1780 SN65HVD1781 SN65HVD1782 SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 www.ti.com THERMAL INFORMATION PARAMETER TEST CONDITIONS SOIC-8 RqJA Junction-to-ambient thermal resistance (no airflow) DIP-8 RqJB Junction-to-board thermal resistance RqJC Junction-to-case thermal resistamce PD TSD (1) Power dissipation VALUE JEDEC high-K model 138 JEDIC low-K model 242 JEDEC high-K model 59 JEDIC low-K model 128 SOIC-8 62 DIP-8 39 SOIC-8 61 DIP-8 61 VCC = 3.
PAGE 7
SN65HVD1780 SN65HVD1781 SN65HVD1782 www.ti.com SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 PARAMETER MEASUREMENT INFORMATION Input generator rate is 100 kbps, 50% duty cycle, rise and fall times less than 6 nsec, output impedance 50 Ω. 375 W ±1% VCC DE 0 V or 3 V D A VOD 60 W ±1% + _ B –7 V < V(test) < 12 V 375 W ±1% S0301-02 Figure 1.
PAGE 8
SN65HVD1780 SN65HVD1781 SN65HVD1782 SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 www.ti.com PARAMETER MEASUREMENT INFORMATION (continued) 3V A 3V D DE Input Generator RL = 110 W ±1% S1 »3V VI VO 50% 50% 0V B tPZL tPLZ CL = 50 pF ±20% VI 50 W »3V CL Includes Fixture and Instrumentation Capacitance VO 50% 10% VOL S0305-01 NOTE: D at 0 V to test non-inverting output, D at 3 V to test inverting output. Figure 5.
PAGE 9
SN65HVD1780 SN65HVD1781 SN65HVD1782 www.ti.com SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 PARAMETER MEASUREMENT INFORMATION (continued) 3V VCC DE A 0 V or 3 V D B RE Input Generator VI 1 kW ± 1% R VO S1 CL = 15 pF ±20% CL Includes Fixture and Instrumentation Capacitance 50 W 3V VI 50% 50% 0V tPZH(1) tPHZ VOH 90% VO 50% D at 3 V S1 to GND »0V tPZL(1) tPLZ VCC VO 50% D at 0 V S1 to VCC 10% VOL S0307-01 Figure 7.
PAGE 10
SN65HVD1780 SN65HVD1781 SN65HVD1782 SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 www.ti.com PARAMETER MEASUREMENT INFORMATION (continued) VCC A 0 V or 1.5 V R VO 1.5 V or 0 V RE Input Generator VI 1 kW ± 1% S1 B CL = 15 pF ±20% CL Includes Fixture and Instrumentation Capacitance 50 W 3V VI 50% 0V tPZH(2) VOH VO A at 1.5 V B at 0 V S1 to GND 50% GND tPZL(2) VCC VO 50% VOL A at 0 V B at 1.5 V S1 to VCC S0308-01 Figure 8.
PAGE 11
SN65HVD1780 SN65HVD1781 SN65HVD1782 www.ti.com SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 TYPICAL CHARACTERISTICS DRIVER OUTPUT CURRENT vs SUPPLY VOLTAGE RMS SUPPLY CURRENT vs SIGNALING RATE 80 10 70 ICC − RMS Supply Current − mA 0 IO − Driver Output Current − mA TA = 25°C RE at VCC DE at VCC RL = 54 Ω CL = 50 pF −10 −20 −30 TA = 25°C DE at VCC D at VCC RL = 54 Ω −40 VCC = 5 V 60 50 40 VCC = 3.
PAGE 12
SN65HVD1780 SN65HVD1781 SN65HVD1782 SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) HVD1780 DIFFERENTIAL OUTPUT AMPLITUDE and TRANSITION TIME vs SUPPLY VOLTAGE 2.5 RL = 50 W, CL = 50 pF 2.3 VCC = 5.5 V VOD − Differential Output − V 2.1 VCC = 5 V 1.9 1.7 VCC = 4.5 V 1.5 1.3 VCC = 4 V VCC = 3.6 V 1.1 VCC = 3.3 V 0.9 VCC = 3 V 0.7 2700 2500 2300 2100 1900 1700 1500 1300 1100 900 700 500 0.5 Transition Time − ns Figure 13.
PAGE 13
SN65HVD1780 SN65HVD1781 SN65HVD1782 www.ti.com SLLS877F – DECEMBER 2007 – REVISED FEBRUARY 2010 REVISION HISTORY Changes from Original (DECEMBER 2007) to Revision A Page • Changed Receiver propagation delay max value From: 50 ns To: 70 ns. ........................................................................... 5 • Changed tPLZ, tPHZ Receiver disable time From 3000 ns To 100 ns. ....................................................................................
PAGE 14
PACKAGE OPTION ADDENDUM www.ti.
PAGE 15
PACKAGE OPTION ADDENDUM www.ti.com 19-Jul-2010 PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details.
PAGE 16
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN65HVD1780DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 SN65HVD1781DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 SN65HVD1782DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.
PAGE 17
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN65HVD1780DR SOIC D 8 2500 367.0 367.0 35.0 SN65HVD1781DR SOIC D 8 2500 367.0 367.0 35.0 SN65HVD1782DR SOIC D 8 2500 367.0 367.0 35.
PAGE 18
PAGE 19
PAGE 20
PAGE 21
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.