Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLogic ICsLogic IC - Receiver, transceiver TSSOP 24

1

2

3

4

5

6

7

8

9

SN54ABT543A, SN74ABT543A

OCTAL REGISTERED TRANSCEIVERS

WITH 3-STATE OUTPUTS

SCBS157F – JANUARY 1991 – REVISED MAY 1997

1

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

State-of-the-Art

EPIC-

ΙΙ

B

 BiCMOS Design

Significantly Reduces Power Dissipation

ESD Protection Exceeds 2000 V Per

MIL-STD-883, Method 3015; Exceeds 200 V

Using Machine Model (C = 200 pF, R = 0)

Typical V

OLP

(Output Ground Bounce) < 1 V

at V

CC

= 5 V, T

A

= 25°C

High-Drive Outputs (–32-mA I

OH

, 64-mA I

OL

)

Package Options Include Plastic

Small-Outline (DW), Shrink Small-Outline

(DB), and Thin Shrink Small-Outline (PW)

Packages, Ceramic Chip Carriers (FK),

Ceramic Flat (W) Package, and Plastic (NT)

and Ceramic (JT) DIPs

description

The ’ABT543A octal transceivers contain two sets

of D-type latches for temporary storage of data

flowing in either direction. Separate latch-enable

(LEAB

or LEBA) and output-enable (OEAB or

OEBA) inputs are provided for each register to

permit independent control in either direction of

data flow.

The A-to-B enable (CEAB) input must be low to

enter data from A or to output data from B. If CEAB

is low and LEAB is low, the A-to-B latches are

transparent; a subsequent low-to-high transition

of LEAB

puts the A latches in the storage mode.

With CEAB and OEAB both low, the 3-state

B outputs are active and reflect the data present

at the output of the A latches. Data flow from B to

A is similar, but requires using the CEBA

, LEBA,

and OEBA inputs.

To ensure the high-impedance state during power

up or power down, OE should be tied to V

CC

through a pullup resistor; the minimum value of

the resistor is determined by the current-sinking

capability of the driver.

The SN54ABT543A is characterized for operation over the full military temperature range of –55°C to 125°C.

The SN74ABT543A is characterized for operation from –40°C to 85°C.

Copyright  1997, Texas Instruments Incorporated

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of Texas Instruments

standard warranty. Production processing does not necessarily include

testing of all parameters.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

EPIC-ΙΙB is a trademark of Texas Instruments Incorporated.

SN54ABT543A . . . JT OR W PACKAGE

SN74ABT543A . . . DB, DW, NT, OR PW PACKAGE

(TOP VIEW)

1

2

3

4

5

6

7

8

9

10

11

12

24

23

22

21

20

19

18

17

16

15

14

13

LEBA

OEBA

A1

A2

A3

A4

A5

A6

A7

A8

CEAB

GND

V

CC

CEBA

B1

B2

B3

B4

B5

B6

B7

B8

LEAB

OEAB

SN54ABT543A . . . FK PACKAGE

(TOP VIEW)

3212827

12 13

5

6

7

8

9

10

11

25

24

23

22

21

20

19

B2

B3

B4

NC

B5

B6

B7

A2

A3

A4

NC

A5

A6

A7

426

14 15 16 17 18

A8

CEAB

GND

NC

OEAB

LEAB

B8

A1

OEBA

LEBA

NC

CEBA

B1

V

CC

NC – No internal connection

Summary of content (22 pages)

PAGE 1
SN54ABT543A, SN74ABT543A OCTAL REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS157F – JANUARY 1991 – REVISED MAY 1997 D D D D D State-of-the-Art EPIC-ΙΙB  BiCMOS Design Significantly Reduces Power Dissipation ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Typical VOLP (Output Ground Bounce) < 1 V at VCC = 5 V, TA = 25°C High-Drive Outputs (–32-mA IOH, 64-mA IOL) Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB
PAGE 2
SN54ABT543A, SN74ABT543A OCTAL REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS157F – JANUARY 1991 – REVISED MAY 1997 FUNCTION TABLE† INPUTS OEAB A OUTPUT B CEAB LEAB H X X X Z X X H X Z L H L X L L L L B0‡ L L L L H H † A-to-B data flow is shown; B-to-A flow control is the same except that it uses CEBA, LEBA, and OEBA.
PAGE 3
SN54ABT543A, SN74ABT543A OCTAL REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS157F – JANUARY 1991 – REVISED MAY 1997 logic diagram (positive logic) OEBA CEBA LEBA OEAB CEAB LEAB A1 2 23 1 13 11 14 C1 3 1D 22 B1 C1 1D To Seven Other Channels Pin numbers shown are for the DB, DW, JT, NT, PW, and W packages. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
SN54ABT543A, SN74ABT543A OCTAL REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS157F – JANUARY 1991 – REVISED MAY 1997 recommended operating conditions (see Note 3) SN54ABT543A VCC VIH Supply voltage VIL VI Low-level input voltage IOH IOL High-level output current ∆t/∆v Input transition rise or fall rate High-level input voltage SN74ABT543A MIN MAX MIN MAX 4.5 5.5 4.5 5.5 2 2 0.
PAGE 5
SN54ABT543A, SN74ABT543A OCTAL REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS157F – JANUARY 1991 – REVISED MAY 1997 timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 1) SN54ABT543A VCC = 5 V, TA = 25°C MIN tw Pulse duration, LEAB or LEBA low Data before LEAB or LEBA↑ tsu Setup time Data before CEAB or CEBA↑ th Hold time MIN MAX UNIT MAX 3.5 3.5 High 2.5 2.5 Low 3 3 High 2.5 2.
PAGE 6
SN54ABT543A, SN74ABT543A OCTAL REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS157F – JANUARY 1991 – REVISED MAY 1997 switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) SN54ABT543A PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A or B B or A tPLH tPHL LEBA or LEAB A or B tPZH tPZL OEBA or OEAB A or B tPHZ tPLZ OEBA or OEAB A or B tPZH tPZL CEBA or CEAB A or B tPHZ tPLZ CEBA or CEAB A o
PAGE 7
SN54ABT543A, SN74ABT543A OCTAL REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS157F – JANUARY 1991 – REVISED MAY 1997 PARAMETER MEASUREMENT INFORMATION 7V S1 500 Ω From Output Under Test Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open LOAD CIRCUIT 3V Timing Input 1.5 V 0V tw tsu 3V Input 1.5 V th 3V 1.5 V Data Input 1.5 V 1.5 V 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V 1.5 V Input 0V 1.5 V 1.
PAGE 8
PACKAGE OPTION ADDENDUM www.ti.
PAGE 9
PACKAGE OPTION ADDENDUM www.ti.
PAGE 10
PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device.
PAGE 11
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN74ABT543ADBR Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SSOP DB 24 2000 330.0 16.4 8.2 8.8 2.5 12.0 16.0 Q1 SN74ABT543ADWR SOIC DW 24 2000 330.0 24.4 10.75 15.7 2.7 12.0 24.0 Q1 SN74ABT543APWR TSSOP PW 24 2000 330.0 16.4 6.95 8.3 1.6 8.0 16.
PAGE 12
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74ABT543ADBR SSOP DB 24 2000 367.0 367.0 38.0 SN74ABT543ADWR SOIC DW 24 2000 367.0 367.0 45.0 SN74ABT543APWR TSSOP PW 24 2000 367.0 367.0 38.
PAGE 13
MECHANICAL DATA MCER004A – JANUARY 1995 – REVISED JANUARY 1997 JT (R-GDIP-T**) CERAMIC DUAL-IN-LINE 24 LEADS SHOWN PINS ** A 13 24 B 1 24 28 A MAX 1.280 (32,51) 1.460 (37,08) A MIN 1.240 (31,50) 1.440 (36,58) B MAX 0.300 (7,62) 0.291 (7,39) B MIN 0.245 (6,22) 0.285 (7,24) DIM 12 0.070 (1,78) 0.030 (0,76) 0.100 (2,54) MAX 0.320 (8,13) 0.290 (7,37) 0.015 (0,38) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0°–15° 0.014 (0,36) 0.008 (0,20) 0.
PAGE 14
MECHANICAL DATA MCFP007 – OCTOBER 1994 W (R-GDFP-F24) CERAMIC DUAL FLATPACK 0.375 (9,53) 0.340 (8,64) Base and Seating Plane 0.006 (0,15) 0.004 (0,10) 0.090 (2,29) 0.045 (1,14) 0.045 (1,14) 0.026 (0,66) 0.395 (10,03) 0.360 (9,14) 0.360 (9,14) 0.240 (6,10) 1 0.360 (9,14) 0.240 (6,10) 24 0.019 (0,48) 0.015 (0,38) 0.050 (1,27) 0.640 (16,26) 0.490 (12,45) 0.030 (0,76) 0.015 (0,38) 12 13 30° TYP 1.115 (28,32) 0.840 (21,34) 4040180-5 / B 03/95 NOTES: A. B. C. D. E.
PAGE 15
PAGE 16
PAGE 17
PAGE 18
PAGE 19
PAGE 20
PAGE 21
MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters.
PAGE 22
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.