Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLogic ICsLogic IC - Switch FET bus switch Single supply VQFN 20 (3.5x4.5)

www.ti.com

FEATURES

GND

DBQ, DGV, DW, OR PW PACKAGE

(TOP VIEW)

NC - No internal connection

RGY PACKAGE

(TOP VIEW)

1 20

10 11

GND

NC - No internal connection

DESCRIPTION/ORDERING INFORMATION

SN74CBTLV3245A

LOW-VOLTAGE OCTAL FET BUS SWITCH

SCDS034M – JULY 1997 – REVISED AUGUST 2005

• Standard '245-Type Pinout • Latch-Up Performance Exceeds 250 mA Per

JESD 17

• 5- Ω Switch Connection Between Two Ports

• ESD Protection Exceeds JESD 22

• Rail-to-Rail Switching on Data I/O Ports

– 2000-V Human-Body Model (A114-A)

• I

off

Supports Partial-Power-Down Mode

Operation – 200-V Machine Model (A115-A)

The SN74CBTLV3245A provides eight bits of high-speed bus switching in a standard '245 device pinout. The low

on-state resistance of the switch allows connections to be made with minimal propagation delay.

The device is organized as one 8-bit switch. When output enable ( OE) is low, the 8-bit bus switch is on, and port

A is connected to port B. When OE is high, the switch is open, and the high-impedance state exists between the

two ports.

This device is fully specified for partial-power-down applications using I

off

. The I

off

feature ensures that damaging

current will not backflow through the device when it is powered down. The device has isolation during power off.

To ensure the high-impedance state during power up or power down, OE should be tied to V

through a pullup

resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

ORDERING INFORMATION

PACKAGE

(1)

ORDERABLE PART NUMBER TOP-SIDE MARKING

QFN – RGY Tape and reel SN74CBTLV3245ARGYR CL245A

Tube SN74CBTLV3245ADW

SOIC – DW CBTLV3245A

Tape and reel SN74CBTLV3245ADWR

SSOP (QSOP) – DBQ Tape and reel SN74CBTLV3245ADBQR CBTLV3245A

–40 ° C to 85 ° C

TSSOP – PW Tape and reel SN74CBTLV3245APWR CL245A

TVSOP – DGV Tape and reel SN74CBTLV3245ADGVR CL245A

VFBGA – GQN Tape and reel SN74CBTLV3245AGQNR CL245A

VFBGA – ZQN Tape and reel SN74CBTLV3245AZQNR CL245A

(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at

www.ti.com/sc/package.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (22 pages)

PAGE 1
SN74CBTLV3245A LOW-VOLTAGE OCTAL FET BUS SWITCH www.ti.
PAGE 2
SN74CBTLV3245A LOW-VOLTAGE OCTAL FET BUS SWITCH www.ti.
PAGE 3
SN74CBTLV3245A LOW-VOLTAGE OCTAL FET BUS SWITCH www.ti.com SCDS034M – JULY 1997 – REVISED AUGUST 2005 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range –0.5 4.6 V VI Input voltage range (2) –0.5 4.
PAGE 4
SN74CBTLV3245A LOW-VOLTAGE OCTAL FET BUS SWITCH www.ti.com SCDS034M – JULY 1997 – REVISED AUGUST 2005 Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER Control inputs VIK MIN TYP (1) TEST CONDITIONS –1.2 VCC = 3 V, II = –18 mA II VCC = 3.6 V, VI = VCC or GND Ioff VCC = 0, VI or VO = 0 to 3.6 V ICC VCC = 3.6 V, IO = 0, VI = VCC or GND Control inputs VCC = 3.
PAGE 5
SN74CBTLV3245A LOW-VOLTAGE OCTAL FET BUS SWITCH www.ti.com SCDS034M – JULY 1997 – REVISED AUGUST 2005 PARAMETER MEASUREMENT INFORMATION 2 × VCC S1 RL From Output Under Test Open GND CL (see Note A) TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND RL LOAD CIRCUIT VCC CL RL V∆ 2.5 V ±0.2 V 3.3 V ±0.3 V 30 pF 50 pF 500 Ω 500 Ω 0.15 V 0.
PAGE 6
PACKAGE OPTION ADDENDUM www.ti.
PAGE 7
PACKAGE OPTION ADDENDUM www.ti.
PAGE 8
PACKAGE OPTION ADDENDUM www.ti.com 18-Oct-2013 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties.
PAGE 9
PACKAGE MATERIALS INFORMATION www.ti.com 8-Jul-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN74CBTLV3245ADBQR Package Package Pins Type Drawing SSOP SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 9.0 2.1 8.0 16.0 Q1 DBQ 20 2500 330.0 16.4 SN74CBTLV3245ADGVR TVSOP DGV 20 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 SN74CBTLV3245ADWR SOIC DW 20 2000 330.0 24.4 10.8 13.3 2.7 12.0 24.
PAGE 10
PACKAGE MATERIALS INFORMATION www.ti.com 8-Jul-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74CBTLV3245ADBQR SSOP DBQ 20 2500 367.0 367.0 38.0 SN74CBTLV3245ADGVR TVSOP DGV 20 2000 367.0 367.0 35.0 SN74CBTLV3245ADWR SOIC DW 20 2000 367.0 367.0 45.0 SN74CBTLV3245APWR TSSOP PW 20 2000 364.0 364.0 27.0 SN74CBTLV3245ARGYR VQFN RGY 20 3000 367.0 367.0 35.0 ZQN 20 1000 338.1 338.1 20.
PAGE 11
PAGE 12
MECHANICAL DATA MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0°– 8° 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters.
PAGE 13
PAGE 14
PAGE 15
PAGE 16
PAGE 17
PAGE 18
PAGE 19
PAGE 20
PAGE 21
PAGE 22
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.