Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLogic ICsLogic IC - Shift register Shift register Push pull SOIC 14

CLR

CLK

Pin numbers shown are for the D, J, N, NS, PW, and W packages.

Product

Folder

Sample &

Buy

Technical

Documents

Tools &

Software

Support &

Community

SN54HC164

SN74HC164

SCLS115G –DECEMBER 1982–REVISED SEPTEMBER 2015

SNx4HC164 8-Bit Parallel-Out Serial Shift Registers

1 Features 3 Description

These 8-bit shift registers feature AND-gated serial

• Wide Operating Voltage Range of 2 V to 6 V

inputs and an asynchronous clear (CLR) input. The

• Outputs Can Drive Up to 10 LSTTL Loads

gated serial (A and B) inputs permit complete control

• Low Power Consumption, 80-μA Maximum I

over incoming data; a low at either input inhibits entry

of the new data and resets the first flip-flop to the low

• Typical t

= 20 ns

level at the next clock (CLK) pulse. A high-level input

• ±4-mA Output Drive at 5 V

enables the other input, which then determines the

• Low Input Current of 1-μA Maximum

state of the first flip-flop. Data at the serial inputs can

be changed while CLK is high or low, provided the

• AND-Gated (Enable/Disable) Serial Inputs

minimum set-up time requirements are met. Clocking

• Fully Buffered Clock and Serial Inputs

occurs on the low-to-high-level transition of CLK.

• Direct Clear

• On Products Compliant to MIL-PRF-38535,

Device Information

(1)

All Parameters Are Tested Unless Otherwise

PART NUMBER PACKAGE BODY SIZE (NOM)

Noted. On All Other Products, Production

SOIC (14) 8.65 mm × 3.91 mm

Processing Does Not Necessarily Include Testing

PDIP (14) 19.30 mm × 6.35 mm

SN74HC164

of All Parameters.

SO (14) 10.30 mm × 5.30 mm

TSSOP (14) 5.00 mm × 4.40 mm

2 Applications

CDIP (14) 19.94 mm × 6.92 mm

• Programable Logic Controllers

SN54HC164 CFP (14) 9.21 mm × 6.29 mm

• Appliances

LCCC (14) 9.39 mm × 9.39 mm

• Video Display Systems

(1) For all available packages, see the orderable addendum at

• Output Expander

the end of the data sheet.

Logic Diagram (Positive Logic)

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

Summary of content (33 pages)

PAGE 1
Sample & Buy Product Folder Support & Community Tools & Software Technical Documents SN54HC164, SN74HC164 SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 SNx4HC164 8-Bit Parallel-Out Serial Shift Registers 1 Features 3 Description • • • • • • • • • • These 8-bit shift registers feature AND-gated serial inputs and an asynchronous clear (CLR) input.
PAGE 2
SN54HC164, SN74HC164 SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Device Comparison Table..................................... Pin Configuration and Functions .........
PAGE 3
SN54HC164, SN74HC164 www.ti.com SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 5 Device Comparison Table PART NUMBER PACKAGE BODY SIZE (NOM) SN74HC164D SOIC (14) 8.65 mm × 3.91 mm SN74HC164N PDIP (14) 19.30 mm × 6.35 mm SN74HC164NS SO (14) 10.30 mm × 5.30 mm SN74HC164PW TSSOP (14) 5.00 mm × 4.40 mm SN54HC164J CDIP (14) 19.94 mm × 6.92 mm SN54HC164W CFP (14) 9.21 mm × 6.29 mm SN54HC164FK LCCC (14) 9.39 mm × 9.
PAGE 4
SN54HC164, SN74HC164 SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 www.ti.com 6 Pin Configuration and Functions D, N, NS, J, W, or PW Package 14-Pin SOIC, PDIP, SO, CDIP, CFP, or TSSOP Top View A B QA QB QC QD GND 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC QH QG QF QE CLR CLK Pin Functions PIN SOIC, PDIP, SO, CDIP, CFP, or TSSOP NO.
PAGE 5
SN54HC164, SN74HC164 www.ti.com SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 B A NC VCC QH FK Package 20-Pin LCCC Top View 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 QG NC QF NC QE QD GND NC CLK CLR QA NC QB NC QC NC – No internal connection Pin Functions PIN LCCC NO.
PAGE 6
SN54HC164, SN74HC164 SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 www.ti.com 7 Specifications 7.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) VCC Supply voltage (2) MIN MAX UNITS −0.
PAGE 7
SN54HC164, SN74HC164 www.ti.com SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 7.
PAGE 8
SN54HC164, SN74HC164 SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 www.ti.com 7.7 Electrical Characteristics, TA = –55°C to 85°C over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = –20 μA VOH VI = VIH or VIL IOH = –4 mA IOH = –5.2 mA IOL = 20 μA VOL VI = VIH or VIL IOL = 4 mA IOL = 5.2 mA II VI = VCC or 0 ICC VI = VCC or 0 SN74HC164 VCC IO = 0 Ci MIN 2V 1.9 4.5 V 4.4 6V 5.9 4.5 V 3.84 6V 5.34 TYP MAX UNIT V 2V 0.
PAGE 9
SN54HC164, SN74HC164 www.ti.com SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 7.9 Timing Requirements, TA = –55°C to 125°C over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VCC MIN fclock Clock frequency NOM tw Pulse duration CLK high or low Data tsu Setup time before CLK↑ CLR inactive th Hold time, data after CLK↑ MAX MIN NOM UNIT MAX 2V 4.2 4.2 4.5 V 21 21 6V CLR low RECOMMENDED SN74HC164 SN54HC164 25 MHz 25 2V 150 125 4.
PAGE 10
SN54HC164, SN74HC164 SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 www.ti.com 7.11 Switching Characteristics, TA = 25°C over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 3) PARAMETER FROM (INPUT) TO (OUTPUT) fmax tPHL CLR tpd Any Q CLK Any Q tt VCC MIN TYP 2V 6 10 4.5 V 31 54 6V 36 62 MAX UNIT MHz 2V 140 205 4.5 V 28 41 6V 24 35 2V 115 175 4.5 V 23 35 6V 20 30 2V 38 75 4.5 V 8 15 6V 6 13 ns ns 7.
PAGE 11
SN54HC164, SN74HC164 www.ti.com SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 7.13 Switching Characteristics, TA = –55°C to 85°C over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 3) PARAMETER FROM (INPUT) TO (OUTPUT) fmax tPHL CLR tpd Any Q CLK Any Q tt VCC SN74HC164 MIN 2V 5 4.5 V 25 6V 28 TYP MAX UNIT MHz 2V 255 4.5 V 51 6V 46 2V 220 4.5 V 44 6V 38 2V 95 4.
PAGE 12
SN54HC164, SN74HC164 SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 www.ti.com 7.14 Typical Characteristics TA = 25°C 120 110 100 90 tpd (ns) 80 70 60 50 40 30 20 10 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VCC (V) 6.5 C001 Figure 2.
PAGE 13
SN54HC164, SN74HC164 www.ti.
PAGE 14
SN54HC164, SN74HC164 SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 www.ti.com 9 Detailed Description 9.1 Overview The SN74HC164 is an 8-bit shift register with 2 serial inputs (A and B) connected through an AND gate, as well as an asynchronous clear (CLR). The device requires a high signal on both A and B in order to set the input data line high; a low signal on either input will set the input data line low.
PAGE 15
SN54HC164, SN74HC164 www.ti.com SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 10 Application and Implementation 10.1 Application Information The SNx4HC164 is an 8-bit shift register that can be used as a deserializer in order to reduce the number of GPIO's needed when driving multiple LED's. In order to correctly display the proper output in the LED's a sink MOSFET was added to prevent the LED's from lighting up until the correct data or the proper clock signal has been achieved. 10.
PAGE 16
SN54HC164, SN74HC164 SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 www.ti.com Typical Application (continued) 10.2.3 Application Curve 120 110 100 90 tpd (ns) 80 70 60 50 40 30 20 10 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VCC (V) 6.5 C001 Figure 5.
PAGE 17
SN54HC164, SN74HC164 www.ti.com SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 11 Power Supply Recommendations The power supply can be any voltage between the minimum and maximum supply voltage rating located in the Recommended Operating Conditions table. Each VCC pin must have a good bypass capacitor in order to prevent power disturbance. For devices with a single supply, a 0.1-μF capacitor is recommended and if there are multiple VCC pins then a 0.01-μF or 0.
PAGE 18
SN54HC164, SN74HC164 SCLS115G – DECEMBER 1982 – REVISED SEPTEMBER 2015 www.ti.com 13 Device and Documentation Support 13.1 Documentation Support 13.1.1 Related Documentation For related docunmentation, see the following: Implications of Slow or Floating CMOS Inputs, SCBA004 13.2 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 2.
PAGE 19
PACKAGE OPTION ADDENDUM www.ti.
PAGE 20
PACKAGE OPTION ADDENDUM www.ti.
PAGE 21
PACKAGE OPTION ADDENDUM www.ti.com 31-Jan-2016 (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device.
PAGE 22
PACKAGE MATERIALS INFORMATION www.ti.com 10-Mar-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN74HC164DR SOIC D 14 2500 330.0 16.8 6.5 9.5 2.3 8.0 16.0 Q1 SN74HC164DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN74HC164DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.
PAGE 23
PACKAGE MATERIALS INFORMATION www.ti.com 10-Mar-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74HC164DR SOIC D 14 2500 364.0 364.0 27.0 SN74HC164DR SOIC D 14 2500 333.2 345.9 28.6 SN74HC164DR SOIC D 14 2500 367.0 367.0 38.0 SN74HC164DRG3 SOIC D 14 2500 364.0 364.0 27.0 SN74HC164DRG4 SOIC D 14 2500 333.2 345.9 28.6 SN74HC164DRG4 SOIC D 14 2500 367.0 367.0 38.
PAGE 24
PAGE 25
PAGE 26
PAGE 27
PAGE 28
PAGE 29
PAGE 30
PAGE 31
PAGE 32
PAGE 33
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.