PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) SNJ54S15J OBSOLETE CDIP J 14 TBD Call TI Call TI -55 to 125 SNJ54S15W OBSOLETE CFP W 14 TBD Call TI Call TI -55 to 125 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs.
PACKAGE OPTION ADDENDUM www.ti.
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN74LS151DR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 SN74LS151NSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74LS151DR SN74LS151NSR SOIC D 16 2500 333.2 345.9 28.6 SO NS 16 2000 367.0 367.0 38.
MECHANICAL DATA MCDI004A – JANUARY 1995 – REVISED NOVEMBER 1997 J (R-GDIP-T**) CERAMIC DUAL-IN-LINE PACKAGE 24 PINS SHOWN B 13 24 C 1 12 0.065 (1,65) 0.045 (1,14) Lens Protrusion (Lens Optional) 0.010 (0.25) MAX 0.175 (4,45) 0.140 (3,56) 0.090 (2,29) 0.060 (1,53) A Seating Plane 0.018 (0,46) MIN 24 PINS ** DIM ”A” ”B” ”C” NARR 0.125 (3,18) MIN 0.022 (0,56) 0.014 (0,36) 0.100 (2,54) 0.012 (0,30) 0.008 (0,20) 28 WIDE NARR 40 32 WIDE NARR WIDE NARR WIDE MAX 0.624(15,85) 0.
MECHANICAL DATA MCFP007 – OCTOBER 1994 W (R-GDFP-F24) CERAMIC DUAL FLATPACK 0.375 (9,53) 0.340 (8,64) Base and Seating Plane 0.006 (0,15) 0.004 (0,10) 0.090 (2,29) 0.045 (1,14) 0.045 (1,14) 0.026 (0,66) 0.395 (10,03) 0.360 (9,14) 0.360 (9,14) 0.240 (6,10) 1 0.360 (9,14) 0.240 (6,10) 24 0.019 (0,48) 0.015 (0,38) 0.050 (1,27) 0.640 (16,26) 0.490 (12,45) 0.030 (0,76) 0.015 (0,38) 12 13 30° TYP 1.115 (28,32) 0.840 (21,34) 4040180-5 / B 03/95 NOTES: A. B. C. D. E.
MECHANICAL DATA MPDI006B – SEPTEMBER 2001 – REVISED APRIL 2002 N (R–PDIP–T24) PLASTIC DUAL–IN–LINE 1.222 (31,04) MAX 24 13 0.360 (9,14) MAX 1 12 0.070 (1,78) MAX 0.200 (5,08) MAX 0.425 (10,80) MAX 0.020 (0,51) MIN Seating Plane 0.125 (3,18) MIN 0.100 (2,54) 0’–15’ 0.021 (0,53) 0.015 (0,38) 0.010 (0,25) 0.010 (0,25) NOM 4040051–3/D 09/01 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.