Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - drivers 2/0 PDIP 14

  

  

SLLS106G − DECEMBER 1975 − REVISED NOVEMBER 2004

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

D Improved Stability Over Supply Voltage and

Temperature Ranges

D Constant-Current Outputs

D High Speed

D Standard Supply Voltages

D High Output Impedance

D High Common-Mode Output Voltage Range

. . . −3 V to 10 V

D TTL-Input Compatibility

D Inhibitor Available for Driver Selection

D Glitch Free During Power Up/Power Down

D SN75112 and External Circuit Meets or

Exceeds the Requirements of CCITT

Recommendation V.35

description/ordering information

The SN55110A, SN75110A, and SN75112 dual

line drivers have improved output current

regulation with supply-voltage and temperature

variations. In addition, the higher current of the

SN75112 (27 mA) allows data to be transmitted

over longer lines. These drivers offer optimum

performance when used with the SN55107A,

SN75107A, and SN75108A line receivers.

ORDERING INFORMATION

PACKAGE

†

ORDERABLE

PART NUMBER

TOP-SIDE

MARKING

PDIP (N)

Tube of 25

SN75110AN SN75110AN

PDIP (N) Tube of 25

SN75112N SN75112N

Tube of 50 SN75110AD

SN75110A

0°C to 70°C

SOIC (D)

Reel of 2500 SN75110ADR

SN75110A

0 C to 70 C

SOIC (D)

Tube of 50 SN75112D

SN75112

Reel of 2500 SN75112DR

SN75112

SOP (NS) Reel of 2000 SN75110ANSR SN75110A

CDIP (J)

Tube of 25

SN55110AJ SN55110AJ

−55°C to 125°C

CDIP (J) Tube of 25

SNJ55110AJ SNJ55110AJ

−55

C to 125

CFP (W) Tube of 150 SNJ55110AW SNJ55110AW

LCCC (FK) Tube of 55 SNJ55110AFK SNJ55110AFK

†

Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines

are available at www.ti.com/sc/package.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

    !   "#$ %!&

%   "! "! '! !  !( !

%% )*& % "!+ %!  !!$* $%!

!+  $$ "!!&

GND

CC+

CC−

SN55110A ...J OR W PACKAGE

SN75110A . . . D, N, OR NS PACKAGE

SN75112 ...D OR N PACKAGE

(TOP VIEW)

3212019

910111213

CC−

SN55110A . . . FK PACKAGE

(TOP VIEW)

GND

CC+

NC − No internal connection

 "% "$  ,-.-/0/ $$ "!! ! !!%

$! '!)! !%&  $$ '! "% "%

"!+ %!  !!$* $%! !+  $$ "!!&

Summary of content (22 pages)

PAGE 1
SLLS106G − DECEMBER 1975 − REVISED NOVEMBER 2004 D Improved Stability Over Supply Voltage and D D D D Temperature Ranges Constant-Current Outputs High Speed Standard Supply Voltages High Output Impedance High Common-Mode Output Voltage Range . . . −3 V to 10 V TTL-Input Compatibility Inhibitor Available for Driver Selection Glitch Free During Power Up/Power Down SN75112 and External Circuit Meets or Exceeds the Requirements of CCITT Recommendation V.
PAGE 2
SLLS106G − DECEMBER 1975 − REVISED NOVEMBER 2004 description/ordering information (continued) These drivers feature independent channels with common voltage supply and ground terminals. The significant difference between the three drivers is in the output-current specification. The driver circuits feature a constant output current that is switched to either of two output terminals by the appropriate logic levels at the input terminals.
PAGE 3
SLLS106G − DECEMBER 1975 − REVISED NOVEMBER 2004 schematic (each driver) VCC+ 14 + C D 2.2 kΩ NOM 3, 4 10 To Other Driver − − + 2.2 kΩ NOM 8, 13 9, 12 A B GND Y Z 1, 5 2, 6 7 − Common to Both Drivers + VCC− 11 − + . . . VCC+ Bus − . . . VCC− Bus − To Other Driver Pin numbers shown are for the D, J, N, NS, and W packages.
PAGE 4
SLLS106G − DECEMBER 1975 − REVISED NOVEMBER 2004 absolute maximum ratings over operating free-air temperature (unless otherwise noted)† Supply voltage: VCC+ (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V VCC− (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −7 V Input voltage, VI . . . . . . . . . . .
PAGE 5
SLLS106G − DECEMBER 1975 − REVISED NOVEMBER 2004 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) SN55110A SN75110A TEST CONDITIONS† PARAMETER MIN VIK Input clamp voltage IO(on) On-state output current VCC± = MIN, VCC± = MAX, SN75112 TYP‡ MAX −0.9 12 IL = −12 mA VO = 10 V MAX −1.5 −0.9 −1.
PAGE 6
SLLS106G − DECEMBER 1975 − REVISED NOVEMBER 2004 PARAMETER MEASUREMENT INFORMATION VCC+ Input A or B VCC− 50 Ω 890 Ω 890 Ω Output Y RL = 50 Ω CL = 40 pF (see Note A) RL = 50 Ω CL = 40 pF (see Note A) Pulse Generator (See Note B) Output Z Pulse Generator (See Note B) To Other Driver Input C or D See Note C 50 Ω TEST CIRCUIT 3V 50% Input A or B 50% 0V tw1 tw2 3V 50% Enable C or D 50% 0V tPLH tPHL tPLH tPHL Off Output Y 50% 50% 50% 50% On t
PAGE 7
SLLS106G − DECEMBER 1975 − REVISED NOVEMBER 2004 TYPICAL CHARACTERISTICS SN75112 ON-STATE OUTPUT CURRENT vs NEGATIVE SUPPLY VOLTAGE SN55110A, SN75110A ON-STATE OUTPUT CURRENT vs NEGATIVE SUPPLY VOLTAGE 35 VCC+ = 4.5 V VO = −3 V TA = 25°C 12 I O(on) − On-State Output Current − mA I O(on) − On-State Output Current − mA 14 10 8 6 4 2 0 −3 −4 −5 −6 −7 30 VCC+ = 4.
PAGE 8
SLLS106G − DECEMBER 1975 − REVISED NOVEMBER 2004 APPLICATION INFORMATION special pulse-control circuit Figure 4 shows a circuit that can be used as a pulse-generator output or in many other testing applications. INPUT A High Low OUTPUTS Z Y Off On On Off 5V 2 3 3 4 VCC+ Y A Input 1 5 2 5 1 6 4 6 B 2.
PAGE 9
SLLS106G − DECEMBER 1975 − REVISED NOVEMBER 2004 APPLICATION INFORMATION using the SN75112 as a CCITT-recommended V.35 line driver The SN75112 dual line driver, the SN75107A dual line receiver, and some external resistors can be used to implement the data-interchange circuit of CCITT recommendation V.35 (1976) modem specification. The circuit of one channel is shown in Figure 5 and meets the requirement of the interface as specified by Appendix 11 of CCITT V.
PAGE 10
PACKAGE OPTION ADDENDUM www.ti.
PAGE 11
PACKAGE OPTION ADDENDUM www.ti.
PAGE 12
PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device.
PAGE 13
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SN75110ADR SOIC SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) D 14 2500 330.0 16.4 6.5 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 9.0 2.1 8.0 16.0 Q1 SN75110ADR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN75110ANSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.
PAGE 14
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN75110ADR SOIC D 14 2500 333.2 345.9 28.6 SN75110ADR SOIC D 14 2500 367.0 367.0 38.0 SN75110ANSR SO NS 14 2000 367.0 367.0 38.0 SN75112DR SOIC D 14 2500 367.0 367.0 38.
PAGE 15
PAGE 16
PAGE 17
PAGE 18
PAGE 19
PAGE 20
PAGE 21
PAGE 22
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.