Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - drivers 2/0 PDIP 14

DS8830, SN55183, SN75183

DUAL DIFFERENTIAL LINE DRIVERS

SLLS093D – OCTOBER 1972 – REVISED APRIL 1998

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Single 5-V Supply

Differential Line Operation

Dual Channels

TTL Compatibility

Short-Circuit Protection of Outputs

Output Clamp Diodes to Terminate Line

Transients

High-Current Outputs

Quad Inputs

Single-Ended or Differential AND/NAND

Outputs

Designed for Use With Dual Differential

Drivers SN55182 and SN75182

Designed to Be Interchangeable With

National Semiconductor DS7830 and

DS8830

description

The DS8830, SN55183, and SN75183 dual

differential line drivers are designed to provide

differential output signals with high current

capability for driving balanced lines, such as

twisted pair, at normal line impedances without

high power dissipation. These devices can be

used as TTL expander/phase splitters, because

the output stages are similar to TTL totem-pole

outputs.

The driver is of monolithic single-chip construction, and both halves of the dual circuits use common power

supply and ground terminals.

The SN55183 is characterized for operation over the full military temperature range of –55°C to 125°C. The

DS8830 and SN75183 are characterized for operation from 0°C to 70°C.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of Texas Instruments

standard warranty. Production processing does not necessarily include

testing of all parameters.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

GND

SN55183 ...J OR W PACKAGE

SN75183 ...D OR N PACKAGE

DS8830 ... N PACKAGE

(TOP VIEW)

3 2 1 20 19

910111213

SN55183 . . . FK PACKAGE

(TOP VIEW)

GND

THE DS8830 AND SN55183 ARE

NOT RECOMMENDED FOR NEW DESIGNS

NC – No internal connection

Summary of content (22 pages)

PAGE 1
DS8830, SN55183, SN75183 DUAL DIFFERENTIAL LINE DRIVERS SLLS093D – OCTOBER 1972 – REVISED APRIL 1998 D D description The DS8830, SN55183, and SN75183 dual differential line drivers are designed to provide differential output signals with high current capability for driving balanced lines, such as twisted pair, at normal line impedances without high power dissipation. These devices can be used as TTL expander/phase splitters, because the output stages are similar to TTL totem-pole outputs. SN55183 . . .
PAGE 2
DS8830, SN55183, SN75183 DUAL DIFFERENTIAL LINE DRIVERS SLLS093D – OCTOBER 1972 – REVISED APRIL 1998 logic symbol† 1A 1B 1C 1D 2A 2B 2C 2D 1 & 5 2 3 6 4 1Z 10 9 11 12 8 13 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the D, J, N, and W packages.
PAGE 3
DS8830, SN55183, SN75183 DUAL DIFFERENTIAL LINE DRIVERS SLLS093D – OCTOBER 1972 – REVISED APRIL 1998 schematic (each driver) 14 VCC 545 Ω V 2 kΩ 3 kΩ 9Ω 6, 8 Z 1, 10 A 300 Ω 2, 11 B 545 Ω V 3, 12 C 4 kΩ D 3.2 kΩ 3 kΩ 9Ω 4, 13 5, 9 Y 2 kΩ 300 Ω 7 GND Resistor values shown are nominal. Pin numbers shown are for the D, J, N, and W packages.
PAGE 4
DS8830, SN55183, SN75183 DUAL DIFFERENTIAL LINE DRIVERS SLLS093D – OCTOBER 1972 – REVISED APRIL 1998 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
DS8830, SN55183, SN75183 DUAL DIFFERENTIAL LINE DRIVERS SLLS093D – OCTOBER 1972 – REVISED APRIL 1998 electrical characteristics over recommended ranges of VCC and operating free-air temperature (unless otherwise noted) PARAMETER TEST CONDITIONS VOH High level output voltage High-level Y (AND) outputs VIH = 2 V IOH = –0.8 mA IOH = –40 mA VOL Low level output voltage Low-level Y (AND) outputs 8V VIL = 0 0.
PAGE 6
DS8830, SN55183, SN75183 DUAL DIFFERENTIAL LINE DRIVERS SLLS093D – OCTOBER 1972 – REVISED APRIL 1998 PARAMETER MEASUREMENT INFORMATION 2.5 V Input VCC = ±5 V Input 1.5 V 1.5 V 0V tPLH Pulse Generator (see Note A) CL = 15 pF (see Note B) CL = 15 pF (see Note B) Y Output tPHL VOH Y Output 1.5 V 1.5 V VOL tPLH tPHL Z Output VOH Z Output 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS TEST CIRCUIT (a) OUTPUTS Y AND Z Input VCC = 5 V Pulse Generator (see Note A) 100 W 3V Y Output Input 1.5 V 1.
PAGE 7
DS8830, SN55183, SN75183 DUAL DIFFERENTIAL LINE DRIVERS SLLS093D – OCTOBER 1972 – REVISED APRIL 1998 TYPICAL CHARACTERISTICS† INPUT THRESHOLD VOLTAGE vs FREE-AIR TEMPERATURE V T – Input Threshold Voltage – V 2.2 2 1.8 1.6 1.4 1.2 1 0.8 ÏÏÏÏÏÏÏÏ ÏÏÏÏÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏÏ ÏÏÏÏ VCC = 5 V VO = 1.5 V VIH min NAND Gate AND Gate VIL max 0.6 0.4 –75 –25 0 25 50 75 100 50-Ω Load 3 2.5 TA = 25°C 2 TA = – 55°C 1.5 1 TA = 125°C 0.
PAGE 8
DS8830, SN55183, SN75183 DUAL DIFFERENTIAL LINE DRIVERS SLLS093D – OCTOBER 1972 – REVISED APRIL 1998 TYPICAL CHARACTERISTICS† TOTAL POWER DISSIPATION (BOTH DRIVERS) vs FREQUENCY PROPAGATION DELAY TIME (DIFFERENTIAL OUTPUT) vs FREE-AIR TEMPERATURE ÏÏÏÏÏÏ ÏÏÏÏÏÏ 240 20 220 PD – Total Power Dissipation – mW t pd – Propagation Delay Time – ns VCC = 5 V See Figure 1(b) 15 ÏÏÏ ÏÏÏ ÏÏÏ ÏÏÏ 10 tPLH tPHL 5 200 180 ÏÏÏÏÏÏÏ ÁÁ ÏÏÏÏÏÏÏ ÁÁ ÏÏÏÏÏÏÏ ÁÁ VCC = 5 V No Load Input: 3-V Square Wave TA = 25°C 16
PAGE 9
DS8830, SN55183, SN75183 DUAL DIFFERENTIAL LINE DRIVERS SLLS093D – OCTOBER 1972 – REVISED APRIL 1998 APPLICATION INFORMATION VCC = 5 V VCC = 5 V 1/2 ’183 Inputs A B C D Inverting Input Z 1/2 ’182 0.002 µF (see Note A) Output RT Resp Time Cont Y Twisted Pair 100 pF (see Note B) Noninverting Input Strobe GND GND NOTES: A. When the inputs are open circuited, the output is high. A capacitor may be used for dc isolation of the line-terminating resistor.
PAGE 10
PACKAGE OPTION ADDENDUM www.ti.
PAGE 11
PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
PAGE 12
PACKAGE OPTION ADDENDUM www.ti.
PAGE 13
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN75183NSR Package Package Pins Type Drawing SO NS 14 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 16.4 Pack Materials-Page 1 8.2 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 10.5 2.5 12.0 16.
PAGE 14
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN75183NSR SO NS 14 2000 367.0 367.0 38.
PAGE 15
PAGE 16
PAGE 17
PAGE 18
PAGE 19
PAGE 20
PAGE 21
PAGE 22
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.