Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - drivers 2/0 PDIP 8







SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995



POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

PERIPHERAL DRIVERS FOR

HIGH-VOLTAGE, HIGH-CURRENT DRIVER

APPLICATIONS

• Characterized for Use to 300 mA

• High-Voltage Outputs

• No Output Latch-Up at 30 V (After

Conducting 300 mA)

• Medium-Speed Switching

• Circuit Flexibility for Varied Applications

and Choice of Logic Function

• TTL-Compatible Diode-Clamped Inputs

• Standard Supply Voltages

• Plastic DIP (P) With Copper Lead Frame for

Cooler Operation and Improved Reliability

• Package Options Include Plastic Small

Outline Packages, Ceramic Chip Carriers,

and Standard Plastic and Ceramic 300-mil

DIPs

SUMMARY OF SERIES 55461/75461

DEVICE LOGIC PACKAGES

SN55461 AND FK, JG

SN55462 NAND FK, JG

SN55463 OR FK, JG

SN75461 AND D, P

SN75462 NAND D, P

SN75463 OR D, P

description

These dual peripheral drivers are functionally interchangeable with SN55451B through SN55453B and

SN75451B through SN75453B peripheral drivers, but are designed for use in systems that require higher

breakdown voltages than those devices can provide at the expense of slightly slower switching speeds. Typical

applications include logic buffers, power drivers, relay drivers, lamp drivers, MOS drivers, line drivers, and

memory drivers.

The SN55461/SN75461, SN55462/SN75462, and SN55463/SN75463 are dual peripheral AND, NAND, and

OR drivers respectively (assuming positive logic), with the output of the gates internally connected to the bases

of the npn output transistors.

Series SN55461 drivers are characterized for operation over the full military temperature range of −55°C

to 125°C. Series SN75461 drivers are characterized for operation from 0°C to 70°C.

GND

SN55461, SN55462, SN55463 . . . JG PACKAGE

SN75461, SN75462, SN75463 ...D OR P PACKAGE

(TOP VIEW)

3 2 1 20 19

910111213

SN55461, SN55462, SN55463 . . . FK PACKAGE

(TOP VIEW)

GND

NC − No internal connection

   ! "#$ !  %#&'" ($)

(#"! "  !%$""! %$ *$ $!  $+! !#$!

!(( ,-) (#" %"$!!. ($!  $"$!!'- "'#($

$!.  '' %$$!)

Summary of content (16 pages)

PAGE 1
SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 PERIPHERAL DRIVERS FOR HIGH-VOLTAGE, HIGH-CURRENT DRIVER APPLICATIONS • • • • 1A 1B 1Y GND LOGIC SN55461 AND FK, JG SN55462 NAND FK, JG SN55463 OR FK, JG SN75461 AND D, P SN75462 NAND D, P SN75463 OR D, P 8 2 7 3 6 4 5 VCC 2B 2A 2Y SN55461, SN55462, SN55463 . . .
PAGE 2
SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† SN55’ Supply voltage, VCC (see Note 1) SN75’ UNIT 7 7 V Input voltage, VI 5.5 5.5 V Intermitter voltage (see Note 2) 5.5 5.
PAGE 3
SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 logic symbol† 1A 1B 2A 2B logic diagram (positive logic) 1 & 2 3 6 5 7 1Y 1A 1B 2Y 2A 2B † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for D, JG, and P packages.
PAGE 4
SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 logic symbol† 1A 1B 2A 2B logic diagram (positive logic) 1 & 2 3 6 5 7 1Y 1A 1B 2Y 2A 2B 3 1 2 5 6 4 Y L L H (off state) L H H (off state) H L H (off state) H H L (on state) GND schematic (each driver) FUNCTION TABLE (each driver) B 2Y 7 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
PAGE 5
SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 logic symbol† 1A 1B 2A 2B logic diagram (positive logic) 1 ≥1 2 3 6 5 7 1Y 1A 5 6 2A 4 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for D, JG, and P packages.
PAGE 6
SLRS022A − DECEMBER 1976 − REVISED OCTOBER 1995 PARAMETER MEASUREMENT INFORMATION ≤ 10 ns ≤ 5 ns Input 2.4 V 10 V RL = 50 Ω ’461 ’462 Output Pulse Generator (see Note A) 90% 1.5 V Input ’461 ’463 Circuit Under Test (see Note B) 10% 10% 0V 0.5 µs ≤ 5 ns Input ’462 CL = 15 pF (see Note B) 90% 1.5 V ≤ 10 ns 3V 90% 1.5 V 10% 10% tPHL GND ’463 tPLH 90% SUB 3V 90% 1.5 V 90% 50% 10% Output 0V VOH 50% 10% VOL 0.
PAGE 7
PACKAGE OPTION ADDENDUM www.ti.
PAGE 8
PACKAGE OPTION ADDENDUM www.ti.com 25-Jan-2012 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production.
PAGE 9
PACKAGE MATERIALS INFORMATION www.ti.com 19-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN75462DR Package Package Pins Type Drawing SOIC D 8 SPQ Reel Reel Diameter Width (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) 6.4 5.2 2.1 8.0 W Pin1 (mm) Quadrant 12.
PAGE 10
PACKAGE MATERIALS INFORMATION www.ti.com 19-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN75462DR SOIC D 8 2500 340.5 338.1 20.
PAGE 11
MECHANICAL DATA MCER001A – JANUARY 1995 – REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0°–15° 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters).
PAGE 12
PAGE 13
PAGE 14
PAGE 15
PAGE 16
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.