Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - receivers RS422 0/4 SOIC 16 N

SN75ALS199

QUADRUPLE DIFFERENTIAL LINE RECEIVER

SLLS046C – JANUARY 1989 – REVISED MAY 1995

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Meets or Exceeds the Requirements of ITU

Recommendations V.10, V.11, X.26, and

X.27

Designed to Operate Up To 20 Mbaud

–7 V to 7 V Common-Mode Input Voltage

Range With 300-mV Sensitivity

3-State TTL-Compatible Outputs

High Input Impedance...12 kΩ Min

Input Hysteresis...120 mV Typ

Single 5-V Supply Operation

Low Supply Current Requirement

35 mA Max

Improved Speed and Power Consumption

Compared to MC3486

description

The SN75ALS199 is a monolithic, quadruple line receiver with 3-state outputs designed using advanced,

low-power, Schottky technology. This technology provides combined improvements in bar design, tooling

production, and wafer fabrication, providing significantly less power consumption and permitting much higher

data throughput than other designs. The device meets the specification of ITU Recommendations V.10, V.11,

X.26, and X.27.

The SN75ALS199 features 3-state outputs that permit direct connection to a bus-organized system with a

fail-safe design that ensures the ouptuts will always be high if the inputs are open. The device is optimized for

balanced multipoint bus transmission at rates up to 20 megabits per second. The input features high-input

impedance, input hysteresis for increased noise immunity, and an input sensitivity of ±300 mV over a

common-mode input voltage range of ±7 V. It also features an active-high enable function for each of two

receiver pairs. The SN75ALS199 is designed for optimum performance when used with the SN75ALS194

quadruple, differential line driver.

The SN75ALS199 is characterized for operation from 0°C to 70°C.

FUNCTION TABLE

(each receiver)

DIFFERENTIAL INPUTS

OUTPUT

A–B

≥ 0.3 V H H

–0.3 V < V

< 0.3 V H ?

≤ –0.3 V H L

X L Z

Open H H

H = high level, L = low level, X = irrelevant,

? = indeterminate, Z = high impedance (off)

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of Texas Instruments

standard warranty. Production processing does not necessarily include

testing of all parameters.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

1, 2EN

GND

3, 4EN

D OR N PACKAGE

(TOP VIEW)

Summary of content (18 pages)

PAGE 1
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 D D D D D D D D D Meets or Exceeds the Requirements of ITU Recommendations V.10, V.11, X.26, and X.27 Designed to Operate Up To 20 Mbaud –7 V to 7 V Common-Mode Input Voltage Range With 300-mV Sensitivity 3-State TTL-Compatible Outputs High Input Impedance . . . 12 kΩ Min Input Hysteresis . . .
PAGE 2
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 logic symbol† 1, 2EN 1A 1B 2A 2B 3, 4EN 3A 3B 4A 4B logic diagram 4 1, 2EN EN 2 3 1 6 5 7 12 1A 1Y 1B 2Y 2A 2B 4 2 3 1 1Y 6 5 7 2Y EN 10 11 9 14 13 15 3Y 3, 4EN 4Y 3A 3B † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
PAGE 3
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI (A or B inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 electrical characteristics over recommended ranges of common-mode input voltage, supply voltage, and operating free-air temperature (unless otherwise noted) PARAMETER VIT + VIT – Positive-going input threshold voltage Vhys VIK Hysteresis voltage (VIT+ – VIT–) VOH High-level output voltage TEST CONDITIONS II = – 18 mA VID = 300 mV, Low level output voltage Low-level VID = – 300 mV IOZ High impedance state o
PAGE 5
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 PARAMETER MEASUREMENT INFORMATION VID VOH VOL IOH (–) IOL (+) 2V Figure 1. VOH and VOL Test Circuit Generator (see Note A) Output 50 Ω CL = 15 pF (see Note B) 3V Input 1.5 V 1.5 V 0V tPLH tPHL VOH 1.5 V Output 1.3 V 1.3 V VOL 2V TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A.
PAGE 6
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 PARAMETER MEASUREMENT INFORMATION SW1 2.5 V Output – 2.5 V SW2 2 kΩ 5V CL = 15 pF (see Note B) Generator (see Note A) 5kΩ See Note C SW3 51 Ω TEST CIRCUIT 3V 3V SW1 to 2.5 V 1.5 V SW2 Open SW3 Closed 0V Input Input 1.5 V 0V tPZH tPZL VOH Output 4.5 V 1.5 V Output 1.5 V 0V tPZH tPZL SW1 to 2.5 V SW2 Closed SW3 Closed 1.5 V Input 1.5 V 0V tPHZ Output VOL 3V SW1 to – 2.
PAGE 7
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs ENABLE VOLTAGE OUTPUT VOLTAGE vs ENABLE VOLTAGE 4 VID = 300 mV VIC = 0 RL = 8 kΩ to GND TA = 25°C 4.5 VO – Output Voltage – V 4 TA = 70°C TA = 25°C TA = 0°C 3.5 VCC = 5.5 V 3 VCC = 5 V VO – Output Voltage – V 5 3.5 VCC = 4.5 V 3 2.5 2 1.5 2.5 2 1.5 1 VCC = 5 V VID = 300 mV VIC = 0 RL = 8 kΩ to GND 1 0.5 0.5 0 0 0 0.5 1 1.5 2 2.5 0 3 0.5 1 2 2.
PAGE 8
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 TYPICAL CHARACTERISTICS HIGH-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE 4 5 VOH – High-Level Output Voltage – V 4 VO – Output Voltage – V IOH = 0 VCC = 5 V VIC = – 12 V to 12 V IO = 0 TA = 25°C 3 2 VIT – VIT + 1 0 – 200 – 150 – 100 – 50 IOH = – 400 µA 3 2 1 VCC = 5 V VID = 300 mV VIC = 0 0 0 50 100 150 200 0 10 20 Figure 8 60 70 80 HIGH-LEVEL O
PAGE 9
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 TYPICAL CHARACTERISTICS LOW-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 0.4 VCC = 5 V VID = – 300 mV VIC = 0 VOL – Low-Level Output Voltage – V 0.35 0.3 0.25 IO = 8 mA 0.2 0.15 IO = 0 0.1 0.05 0 0 10 20 30 40 50 60 70 80 TA – Free-Air Temperature – °C Figure 12 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 0.8 0.8 VCC = 4.5 V VCC = 5 V 0.
PAGE 10
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs SUPPLY VOLTAGE SUPPLY CURRENT vs FREE-AIR TEMPERATURE 50 40 VCC = 5.5 V 25 I CC – Supply Current – mA 45 I CC – Supply Current – mA 30 VID = – 300 mV VIC = 0 IO = 0 TA = 25°C 35 30 Disabled 25 Enabled 20 15 10 VCC = 5 V 20 VCC = 4.
PAGE 11
SN75ALS199 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS046C – JANUARY 1989 – REVISED MAY 1995 TYPICAL CHARACTERISTICS INPUT CURRENT vs INPUT VOLTAGE TO GND INPUT RESISTANCE vs FREE-AIR TEMPERATURE 3 30 TA = 25°C 2 I I – Input Current – mA ri – Input Resistance – k Ω 25 20 15 10 0 –1 –2 5 0 1 0 10 20 30 40 50 60 70 –3 – 20 80 – 15 – 10 0 5 10 15 20 VI – Input Voltage to GND – V TA – Free-Air Temperature – °C Figure 19 Figure 20 SWITCHING TIME vs FREE-AIR TEMPERATURE PROPAG
PAGE 12
PACKAGE OPTION ADDENDUM www.ti.
PAGE 13
PACKAGE MATERIALS INFORMATION www.ti.com 19-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN75ALS199DR Package Package Pins Type Drawing SOIC D 16 SPQ Reel Reel Diameter Width (mm) W1 (mm) 2500 330.0 16.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) 6.5 10.3 2.1 8.0 W Pin1 (mm) Quadrant 16.
PAGE 14
PACKAGE MATERIALS INFORMATION www.ti.com 19-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN75ALS199DR SOIC D 16 2500 333.2 345.9 28.
PAGE 15
PAGE 16
PAGE 17
PAGE 18
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.