Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Audio amplifier 1-channel (mono) or 2-channel (stereo) Class D HTQFP 64 (14x1

0,1

tal Harmonic Distortion - %

4Ohm (6kHz)

4Ohm(1kHz)

TOTAL HARMONIC DISTORTION+NOISE

OUTPUT POWER

0,001

0,01

0,1

0,01 1 100

THD+N - Total Harmonic Distortion - %

- Output Power - W

4Ohm (6kHz)

4Ohm(1kHz)

TOTAL HARMONIC DISTORTION+NOISE

OUTPUT POWER

TC = 75 C

CONFIG = BTL

TAS5611

www.ti.com

SLAS681A –DECEMBER 2009–REVISED APRIL 2010

125W STEREO / 250W MONO PurePath™ HD ANALOG-INPUT POWER STAGE

Check for Samples: TAS5611

FEATURES

APPLICATIONS

• Home Theater Systems

• PurePath™ HD Enabled Integrated Feedback

Provides:

• AV Receivers

• DVD/Blu-ray Receivers

– Signal Bandwidth up to 80kHz for High

Frequency Content From HD Sources

• Mini Combo System

• Active Speakers and Subwoofers

– Ultralow 0.03% THD at 1W into 4Ω

– Flat THD at all Frequencies for Natural

DESCRIPTION

Sound

– 80dB PSRR (BTL, No Input Signal) The TAS5611 is a high performance analog input

Class D amplifier with integrated closed loop

– >100dB (A weighted) SNR

feedback technology (known as PurePath™ HD) with

– Click and Pop Free Startup

the ability to drive up to 125W

(1)

Stereo into 4 to 8 Ω

• Pin compatible with TAS5630, TAS5615 and

Speakers from a single 32.5V supply.

TAS5613

PurePath™ HD technology enables traditional

• Multiple Configurations Possible on the Same

AB-Amplifier performance (<0.03% THD) levels while

PCB With Stuffing Options:

providing the power efficiency of traditional class D

amplifiers.

– Mono Parallel Bridge Tied Load (PBTL)

– Stereo Bridge Tied Load (BTL)

Unlike traditional Class D amplifiers, the distortion

curve only increases once the output levels move into

– 2.1 Single Ended Stereo Pair and Bridge

clipping. PurePath™ HD Power PAD™

Tied Load Subwoofer

PurePath™ HD technology enables lower idle losses

• Total Output Power at 10%THD+N

making the device even more efficient.

– 250W in Mono PBTL Configuration into 2Ω

– 125W per Channel in Stereo BTL

Configuration into 4Ω

• Total Output Power in BTL configuration at

1%THD+N

– 130W Stereo into 3Ω

– 105W Stereo into 4Ω

– 70W Stereo into 6Ω

– 55W Stereo into 8Ω

• >90% Efficient Power Stage With 60-mΩ

Output MOSFETs

• Self-Protection Design (Including

Undervoltage, Overtemperature, Clipping, and

Short-Circuit Protection) With Error Reporting

• EMI Compliant When Used With

Recommended System Design

• Two Thermally Enhanced Package Options:

(1) Achievable output power levels are dependent on the thermal

– PHD (64-Pin QFP)

configuration of the target application. A high performance

– DKD (44-Pin PSOP3)

thermal interface material between the package exposed

heatslug and the heat sink should be used to achieve high

output power levels.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2PurePath, Power PAD are trademarks of Texas Instruments.

3All other trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (29 pages)

PAGE 1
TAS5611 www.ti.com SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 125W STEREO / 250W MONO PurePath™ HD ANALOG-INPUT POWER STAGE Check for Samples: TAS5611 FEATURES APPLICATIONS • • • • • • 23 • • • • • • • • PurePath™ HD Enabled Integrated Feedback Provides: – Signal Bandwidth up to 80kHz for High Frequency Content From HD Sources – Ultralow 0.
PAGE 2
TAS5611 SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
PAGE 3
TAS5611 www.ti.
PAGE 4
TAS5611 SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 www.ti.com ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) VALUE UNIT VDD to GND –0.3 to 13.2 V GVDD to GND –0.3 to 13.2 V –0.3 to 53 V PVDD_X to GND_X (2) OUT_X to GND_X (2) –0.3 to 53 V –0.3 to 66.2 V BST_X to GVDD_X (2) –0.3 to 53 V VREG to GND –0.3 to 4.2 V GND_X to GND –0.3 to 0.3 V GND to AGND –0.3 to 0.
PAGE 5
TAS5611 www.ti.com SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 RECOMMENDED OPERATING CONDITIONS (continued) over operating free-air temperature range (unless otherwise noted) MIN VFREQ_ADJ Voltage on FREQ_ADJ pin for slave mode operation TJ Junction temperature Slave mode TYP MAX UNIT 3.3 0 V 150 °C PIN FUNCTIONS PIN NAME FUNCTION (1) DESCRIPTION PHD NO. DKD NO. AGND 8 10 P Analog ground BST_A 54 43 P HS bootstrap supply (BST), external 0.033 mF capacitor to OUT_A required.
PAGE 6
TAS5611 SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 www.ti.
PAGE 7
TAS5611 www.ti.
PAGE 8
TAS5611 SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 www.ti.
PAGE 9
TAS5611 www.ti.com SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 AUDIO CHARACTERISTICS (BTL) PCB and system configuration are in accordance with recommended guidelines. Audio frequency = 1kHz, PVDD_X = 32.5V, GVDD_X = 12 V, RL = 4Ω, fS = 400kHz, ROC = 30kΩ, TC = 75°C, Output Filter: LDEM = 7mH, CDEM = 680nF, MODE = 010, unless otherwise noted.
PAGE 10
TAS5611 SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 www.ti.com ELECTRICAL CHARACTERISTICS PVDD_X = 32.5V, GVDD_X = 12 V, VDD = 12 V, TC (Case temperature) = 75°C, fS = 400 kHz, unless otherwise specified.
PAGE 11
TAS5611 www.ti.com SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 ELECTRICAL CHARACTERISTICS (continued) PVDD_X = 32.5V, GVDD_X = 12 V, VDD = 12 V, TC (Case temperature) = 75°C, fS = 400 kHz, unless otherwise specified. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT I/O PROTECTION Undervoltage protection limit, GVDD_x and VDD Vuvp,G Vuvp,hyst (1) 9.5 V 0.
PAGE 12
TAS5611 SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 www.ti.com TYPICAL CHARACTERISTICS, BTL CONFIGURATION TOTAL HARMONIC+NOISE vs OUTPUT POWER OUTPUT POWER vs SUPPLY VOLTAGE 200 TC = 75°C TC = 75°C THD+N = 10% 3W 4W 1 8W 0.1 4W 6W 8W 100 50 0.01 0.001 0.01 150 0.1 1 100 10 PO - Output Power - W 0 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PVDD - Supply Voltage - V 1000 Figure 1. Figure 2.
PAGE 13
TAS5611 www.ti.com SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 TYPICAL CHARACTERISTICS, BTL CONFIGURATION (continued) SYSTEM POWER LOSS vs OUTPUT POWER OUTPUT POWER vs CASE TEMPERATURE 40 200 3W TC = 25°C THD+N = 10% 4W 150 PO - Output Power - W Power Loss - W 30 4W 6W 20 8W 6W 100 8W 50 10 THD+N = 10% 0 0 50 100 150 200 250 2 Channel Output Power - W 0 20 300 40 50 60 70 80 TC - Case Temperature - °C 90 Figure 5. Figure 6.
PAGE 14
TAS5611 SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 www.ti.com TYPICAL CHARACTERISTICS, PBTL CONFIGURATION TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER OUTPUT POWER vs SUPPLY VOLTAGE 300 TC = 75°C 2W TC = 75°C THD+N = 10% 3W 2W 250 3W 4W 1 PO - Output Power - W THD+N - Total Harmonic Distortion + Noise - % 10 6W 8W 0.1 200 4W 6W 150 8W 100 0.01 50 0.001 0.01 0.
PAGE 15
TAS5611 www.ti.com SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 APPLICATION INFORMATION PCB MATERIAL RECOMMENDATION FR-4 Glass Epoxy material with 2 oz. (70mm) is recommended for use with the TAS5611. The use of this material can provide for higher power output, improved thermal performance, and better EMI margin (due to lower PCB trace inductance). PVDD CAPACITOR RECOMMENDATION The large capacitors used in conjunction with each full-bridge, are referred to as the PVDD Capacitors.
PAGE 16
R_RIGHT_N IN_RIGHT_P IN_LEFT_N IN_LEFT_P /RESET C10 10uF C16 10uF C14 10uF C12 10uF C17 100pF C15 100pF C13 100pF C11 100pF C18 100pF READY /CLIP /OTW2 /OTW1 /SD OSC_IO- OSC_IO+ 100R R13 100R R12 100R R11 100R R10 100R R18 GND VREG GND R19 47k GND GND GND GND GND 10k R21 100nF C22 VREG 1nF C21 4.
PAGE 17
READY /CLIP /OTW2 /OTW1 /SD 10uF 10uF 100R 100R 100R GND GND GND 100pF 100pF 100pF GND VREG 47k GND GND GND GND GND 10k 100nF 1nF 4.7nF 30k VREG GND GND 1 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 /OTW1 /SD OSC_IO- OSC_IO+ FREQ_ADJ INPUT_D INPUT_C VREG AGND GND VI_CM INPUT_B INPUT_A C_STARTUP /RESET OC_ADJ 330pF GND GND 100nF 100nF GND GND GND GND 100nF 100nF VREG GND GND 100nF TAS5611PHD GND 33nF 3.3R 3.3R 3.
PAGE 18
TAS5611 2 mF 2 mF 30 kW 2 mF www.ti.com 2 mF SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 Figure 14.
PAGE 19
TAS5611 www.ti.com SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 THEORY OF OPERATION POWER SUPPLIES To facilitate system design, the TAS5611 needs only a 12V supply in addition to the (typical) 32.5V power-stage supply. An internal voltage regulator provides suitable voltage levels for the digital and low-voltage analog circuitry. Additionally, all circuitry requiring a floating voltage supply, e.g.
PAGE 20
TAS5611 SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 www.ti.com ERROR REPORTING The SD, OTW, OTW1 and OTW2 pins are active low, open-drain outputs. Their function is for protection-mode signaling to a PWM controller or other system-control device. Any fault resulting in device shutdown is signaled by the SD pin going low. Likewise, OTW and OTW2 goes low when the device junction temperature exceeds 125°C and OTW1 goes low when the junction temperature exceeds 100°C (see the following table).
PAGE 21
TAS5611 www.ti.com SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 <15ms/mF. While the PPSC detection is in progress, SD is kept low, and the device will not react to changes applied to the RESET pins. If no shorts are present the PPSC detection passes, and SD is released. A device reset will not start a new PPSC detection. PPSC detection is enabled in BTL and PBTL output configurations, the detection is not performed in SE mode.
PAGE 22
TAS5611 SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 www.ti.com OSCILLATOR The oscillator frequency can be trimmed by external control of the FREQ_ADJ pin. To reduce interference problems while using radio receiver tuned within the AM band, the switching frequency can be changed from nominal to lower values.
PAGE 23
TAS5611 www.ti.com SLAS681A – DECEMBER 2009 – REVISED APRIL 2010 Note B1: It is important to have a direct low impedance return path for high current back to the power supply. Keep impedance low from top to bottom side of PCB through a lot of ground vias. Note B2: Bootstrap low impedance X7R ceramic capacitors placed on bottom side providing a short low inductance current loop. Note B3: Return currents from bulk capacitors and output filter capacitors. Figure 16.
PAGE 24
PACKAGE OPTION ADDENDUM www.ti.
PAGE 25
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TAS5611PHDR Package Package Pins Type Drawing HTQFP PHD 64 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 1000 330.0 24.4 Pack Materials-Page 1 17.0 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 17.0 1.5 20.0 24.
PAGE 26
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TAS5611PHDR HTQFP PHD 64 1000 367.0 367.0 45.
PAGE 27
PAGE 28
PAGE 29
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.