Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Audio amplifier 1-channel (mono) or 2-channel (stereo) Class D HSSOP 44

PurePath

Class-G Power Supply

Ref. Design

110 VAC 240 VAC®

25 V–50 V

ANALOG

AUDIO

INPUT

12 V

PurePath

TAS5630

(2.1 Configuration)

♫♪

3 OPA1632´

±15 V

TAS5630

www.ti.com

SLES220B –JUNE 2009–REVISED FEBRUARY 2010

300-W STEREO / 600-W MONO PurePath™ HD ANALOG-INPUT POWER STAGE

Check for Samples: TAS5630

FEATURES

APPLICATIONS

• Mini Combo System

• PurePath™ HD Enabled Integrated Feedback

Provides:

• AV Receivers

• DVD Receivers

– Signal Bandwidth up to 80 kHz for

High-Frequency Content From HD Sources

• Active Speakers

– Ultralow 0.03% THD at 1 W into 4 Ω

DESCRIPTION

– Flat THD at all Frequencies for Natural

Sound

The TAS5630 is a high-performance analog-input

class-D amplifier with integrated closed-loop

– 80-dB PSRR (BTL, No Input Signal)

feedback technology (known as PurePath HD

– >100-dB (A-weighted) SNR

technology) with the ability to drive up to 300 W

(1)

– Click- and Pop-Free Start-Up

stereo into 4-Ω to 8-Ω speakers from a single 50-V

supply.

• Multiple Configurations Possible on the Same

PCB With Stuffing Options:

PurePath HD technology enables traditional

– Mono Parallel Bridge-Tied Load (PBTL) AB-amplifier performance (<0.03% THD) levels while

providing the power efficiency of traditional class-D

– Stereo Bridge-Tied Load (BTL)

amplifiers.

– 2.1 Single-Ended Stereo Pair and

Unlike traditional class-D amplifiers, the distortion

Bridge-Tied Load Subwoofer

curve only increases once the output levels move into

– Quad Single-Ended Outputs

clipping. PurePath HD™

• Total Output Power at 10% THD+N

PurePath HD technology enables lower idle losses,

– 600 W in Mono PBTL Configuration

making the device even more efficient. Coupled with

– 300 W per Channel in Stereo BTL

TI’s class-G power-supply reference design for

Configuration

TAS563x, industry-leading levels of efficiency can be

achieved.

– 145 W per Channel in Quad Single-Ended

Configuration

• High-Efficiency Power Stage (>88%) With

60-mΩ Output MOSFETs

• Two Thermally Enhanced Package Options:

– PHD (64-Pin QFP)

– DKD (44-Pin PSOP3)

• Self-Protection Design (Including

Undervoltage, Overtemperature, Clipping, and

Short-Circuit Protection) With Error Reporting

• EMI Compliant When Used With

Recommended System Design

(1) Achievable output power levels are dependent on the thermal

configuration of the target application. A high-performance

thermal interface material between the exposed package heat

slug and the heat sink should be used to achieve high output

power levels.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2PurePath HD is a trademark of Texas Instruments.

3All other trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (36 pages)

PAGE 1
TAS5630 www.ti.com SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 300-W STEREO / 600-W MONO PurePath™ HD ANALOG-INPUT POWER STAGE Check for Samples: TAS5630 FEATURES APPLICATIONS • • • • • 1 23 • • • • • • PurePath™ HD Enabled Integrated Feedback Provides: – Signal Bandwidth up to 80 kHz for High-Frequency Content From HD Sources – Ultralow 0.
PAGE 2
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
PAGE 3
TAS5630 www.ti.
PAGE 4
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.com ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) VALUE UNIT VDD to AGND –0.3 to 13.2 V GVDD to AGND –0.3 to 13.2 V –0.3 to 69 V PVDD_X to GND_X (2) OUT_X to GND_X (2) –0.3 to 69 V –0.3 to 82.2 V BST_X to GVDD_X (2) –0.3 to 69 V VREG to AGND –0.3 to 4.2 V GND_X to GND –0.3 to 0.3 V GND_X to AGND –0.3 to 0.
PAGE 5
TAS5630 www.ti.com SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 PIN FUNCTIONS PIN Function (1) DESCRIPTION 10 P Analog ground 54 43 P HS bootstrap supply (BST), external 0.033-mF capacitor to OUT_A required. 41 34 P HS bootstrap supply (BST), external 0.033-mF capacitor to OUT_B required. BST_C 40 33 P HS bootstrap supply (BST), external 0.033-mF capacitor to OUT_C required. BST_D 27 24 P HS bootstrap supply (BST), external 0.033-mF capacitor to OUT_D required.
PAGE 6
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.com PIN FUNCTIONS (continued) PIN NAME Function (1) DESCRIPTION PHD NO. DKD NO. 30, 31 25, 26 P Power-supply input for half-bridge D requires close decoupling of 0.01-mF capacitor in parallel with 2.2-mF capacitor to GND_D.
PAGE 7
TAS5630 www.ti.
PAGE 8
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.
PAGE 9
TAS5630 www.ti.com SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 AUDIO CHARACTERISTICS (BTL) PCB and system configuration are in accordance with recommended guidelines. Audio frequency = 1 kHz, PVDD_X = 50 V, GVDD_X = 12 V, RL = 4 Ω, fS = 400 kHz, ROC = 22 kΩ, TC = 75°C; output filter: LDEM = 7 mH, CDEM = 680 nF, MODE = 010, unless otherwise noted.
PAGE 10
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.com AUDIO SPECIFICATION (PBTL) PCB and system configuration are in accordance with recommended guidelines. Audio frequency = 1 kHz, PVDD_X = 50 V, GVDD_X = 12 V, RL = 2 Ω, fS = 400 kHz, ROC = 22 kΩ, TC = 75°C; output filter: LDEM = 7 mH, CDEM = 1.5 mF, MODE = 101-10, unless otherwise noted.
PAGE 11
TAS5630 www.ti.com SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 ELECTRICAL CHARACTERISTICS (continued) PVDD_X = 50 V, GVDD_X = 12 V, VDD = 12 V, TC (Case temperature) = 75°C, fS = 400 kHz, unless otherwise specified. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT I/O PROTECTION Undervoltage protection limit, GVDD_x and VDD Vuvp,G Vuvp,hyst (1) 9.5 V 0.
PAGE 12
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.com TYPICAL CHARACTERISTICS, BTL CONFIGURATION TOTAL HARMONIC+NOISE vs OUTPUT POWER OUTPUT POWER vs SUPPLY VOLTAGE THD+N - Total Harmonic Distortion + Noise - % 10 TC = 75°C 5 PO - Output Power - W 2 1 0.5 0.2 4W 0.1 6W 0.05 0.02 8W 0.01 0.
PAGE 13
TAS5630 www.ti.com SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 TYPICAL CHARACTERISTICS, BTL CONFIGURATION (continued) SYSTEM POWER LOSS vs OUTPUT POWER 80 75 70 OUTPUT POWER vs CASE TEMPERATURE 340 320 300 TC = 25°C THD+N at 10% 65 Power Loss - W PO - Output Power - W 4W 60 55 50 45 40 6W 35 30 25 20 15 10 5 0 8W 0 100 200 300 400 500 2 Channel Output Power - W 600 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 10 4W 6W 8W THD+N at 10% 20 Figure 5.
PAGE 14
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.com TYPICAL CHARACTERISTICS, SE CONFIGURATION TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER OUTPUT POWER vs SUPPLY VOLTAGE 5 TC = 75°C 4W 2 3W PO - Output Power - W THD+N - Total Harmonic Distortion + Noise - % 10 1 2W 0.5 0.2 0.1 0.05 0.02 0.01 0.
PAGE 15
TAS5630 www.ti.com SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 TYPICAL CHARACTERISTICS, PBTL CONFIGURATION TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER OUTPUT POWER vs SUPPLY VOLTAGE 5 650 TC = 75°C 2W TC = 75°C THD+N at 10% 2W 550 3W 2 3W 500 4W 1 0.5 0.2 600 PO - Output Power - W THD+N - Total Harmonic Distortion + Noise - % 10 6W 8W 0.1 0.05 450 4W 400 6W 350 8W 300 250 200 150 0.02 100 0.01 0.
PAGE 16
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.com APPLICATION INFORMATION PCB MATERIAL RECOMMENDATION FR-4 2-oz. (70-mm) glass epoxy material is recommended for use with the TAS5630. The use of this material can provide for higher power output, improved thermal performance, and better EMI margin (due to lower PCB trace inductance). PVDD CAPACITOR RECOMMENDATION The large capacitors used in conjunction with each full bridge are referred to as the PVDD capacitors.
PAGE 17
R_RIGHT_N IN_RIGHT_P IN_LEFT_N IN_LEFT_P /RESET 10uF C16 10uF C14 10uF C12 10uF C10 C17 100pF C15 100pF C13 100pF C11 100pF C18 100pF READY /CLIP GND GND R19 47k GND GND GND GND GND 10k R21 100nF C22 VREG 1nF C21 4.7nF 22.0k C20 R20 330pF GND 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 /OTW1 /SD OSC_IO- OSC_IO+ FREQ_ADJ INPUT_D INPUT_C VREG AGND GND VI_CM INPUT_B INPUT_A C_STARTUP /RESET OC_ADJ GND C30 100nF GND 3.
PAGE 18
READY /CLIP /OTW2 /OTW1 /SD OSC_IO- OSC_IO+ IN_N IN_P /RESET 10uF 10uF 100R 100R 100R GND GND GND 100pF 100pF 100pF GND VREG 47k VREG GND GND GND GND GND 10k 100nF 1nF 4.7nF 22.
PAGE 19
READY /CLIP /OTW2 /OTW1 /SD OSC_IO- OSC_IO+ IN_D IN_C IN_B IN_A /RESET Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): TAS5630 147kW 165kW 187kW 191kW 50V 49V 48V <48V GND GND GND GND R_COMP 100R 100R 100R GND 100pF 100pF 100pF 100pF 100pF PVDD PVDD C A Submit Documentation Feedback 470uF 50V 470uF 50V 470uF 50V 470uF 50V GND GND GND GND GND GND GND R_COMP R_COMP 10k 1% 10k 1% 10k 1% 10k 1% 10k 100nF 1nF 10nF 22.
PAGE 20
READY /CLIP /OTW2 /OTW1 /SD OSC_IO- OSC_IO+ IN_RIGHT IN_LEFT IN_CENTER_N IN_CENTER_P /RESET 10uF 10uF 10uF 10uF 100R 100R 100R 100R 100R GND GND GND GND GND 100pF 100pF 100pF 100pF 100pF 47k VREG GND GND GND GND GND 10k 100nF VREG 1nF 10nF 22.
PAGE 21
Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): TAS5630 READY /OTW 10uF 10uF 10uF 10uF 100R R60 100R R53 100R R54 100R R45 100R R13 C81 100pF C80 100pF C79 100pF C82 100pF GND C78 100pF VREG R44 47k GND GND GND GND GND GND R20 10k C86 100nF GND GND VREG 22 21 20 19 18 17 16 15 14 13 12 11 9 8 7 6 5 4 3 2 1 10 VREG GND 1nF GND C35 100nF C42 C85 4.
PAGE 22
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.com THEORY OF OPERATION POWER SUPPLIES To facilitate system design, the TAS5630 needs only a 12-V supply in addition to the (typical) 50-V power-stage supply. An internal voltage regulator provides suitable voltage levels for the digital and low-voltage analog circuitry. Additionally, all circuitry requiring a floating voltage supply, e.g.
PAGE 23
TAS5630 www.ti.com SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 ERROR REPORTING The SD, OTW, OTW1 and OTW2 pins are active-low, open-drain outputs. Their function is for protection-mode signaling to a PWM controller or other system-control device. Any fault resulting in device shutdown is signaled by the SD pin going low. Likewise, OTW and OTW2 go low when the device junction temperature exceeds 125°C and OTW1 goes low when the junction temperature exceeds 100°C (see the following table).
PAGE 24
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.com filter. The typical duration is <15 ms/mF. While the PPSC detection is in progress, SD is kept low, and the device does not react to changes applied to the RESET pins. If no shorts are present the PPSC detection passes, and SD is released, a device reset does not start a new PPSC detection. PPSC detection is enabled in BTL and PBTL output configurations; the detection is not performed in SE mode.
PAGE 25
TAS5630 www.ti.com SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 OSCILLATOR The oscillator frequency can be trimmed by external control of the FREQ_ADJ pin. To reduce interference problems while using a radio receiver tuned within the AM band, the switching frequency can be changed from nominal to lower values.
PAGE 26
TAS5630 SLES220B – JUNE 2009 – REVISED FEBRUARY 2010 www.ti.com Note B1: It is important to have a direct-low impedance return path for high current back to the power supply. Keep impedance low from top to bottom side of PCB through a lot of ground vias. Note B2: Bootstrap low-impedance X7R ceramic capacitors placed on bottom side provide a short, low-inductance current loop. Note B3: Return currents from bulk capacitors and output filter capacitors Figure 20.
PAGE 27
PACKAGE OPTION ADDENDUM www.ti.
PAGE 28
PACKAGE OPTION ADDENDUM www.ti.
PAGE 29
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) TAS5630DKDR HSSOP DKD 44 500 330.0 24.4 TAS5630PHDR HTQFP PHD 64 1000 330.0 24.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 14.7 16.4 4.0 20.0 24.0 Q1 17.0 17.0 1.5 20.0 24.
PAGE 30
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TAS5630DKDR HSSOP DKD TAS5630PHDR HTQFP PHD 44 500 367.0 367.0 45.0 64 1000 367.0 367.0 45.
PAGE 31
PAGE 32
PAGE 33
PAGE 34
PAGE 35
PAGE 36
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.