Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Op-amp, differential amplifier Differential SOIC 8

DGK-8DGN-8 D-8

IN−

IN+

OCM

S+

OUT+

S−

OUT−

APPLICATION CIRCUIT DIAGRAM

f − Frequency − MHz

−80

−92

10 20 40 60

− Third-Order Intermodulation Distortion − dBc

−74

THIRD-ORDER INTERMODULATION

DISTORTION

−62

80 100

−68

−86

−98

IMD

Bits

392 Ω

−

800 Ω

S+

OUT

392 Ω

402 Ω

56.2 Ω

50 Ω

374 Ω

OCM

2.5 V

S−

70 90

= 5 V

= ±5 V

−

OCM

12 Bit/80 MSps

5 V

ref

5 V

0.1 µF 10 µF

392 Ω

10 pF

1 µF

56.2 Ω

ADC

374 Ω

50 Ω

402 Ω

392 Ω

10 pF

24.9 Ω

THS4500

THS4501

www.ti.com

SLOS350F –APRIL 2002–REVISED OCTOBER 2011

WIDEBAND, LOW-DISTORTION, FULLY DIFFERENTIAL AMPLIFIERS

Check for Samples: THS4500, THS4501

FEATURES

APPLICATIONS

• Fully Differential Architecture

• High Linearity Analog-to-Digital Converter

Preamplifier

• Bandwidth: 370 MHz

• Wireless Communication Receiver Chains

• Slew Rate: 2800 V/μs

• Single-Ended to Differential Conversion

• IMD

: –90 dBc at 30 MHz

• Differential Line Driver

• OIP

: 49 dBm at 30 MHz

• Active Filtering of Differential Signals

• Output Common-Mode Control

• Wide Power-Supply Voltage Range: 5 V, ±5 V,

12 V, 15 V

• Input Common-Mode Range Shifted to Include

Negative Power-Supply Rail

• Power-Down Capability (THS4500)

• Evaluation Module Available

DESCRIPTION RELATED DEVICES

DEVICE

(1)

DESCRIPTION

The THS4500 and THS4501 are high-performance

fully differential amplifiers from Texas Instruments.

THS4500/1 370 MHz, 2800 V/μs, V

ICR

Includes V

S–

The THS4500, featuring power-down capability, and

THS4502/3 370 MHz, 2800 V/μs, Centered V

ICR

the THS4501, without power-down capability, set new

THS4120/1 3.3 V, 100 MHz, 43 V/μs, 3.7 nV/√Hz

performance standards for fully differential amplifiers

THS4130/1 ±15 V, 150 MHz, 51 V/μs, 1.3 nV/√Hz

with unsurpassed linearity, supporting 14-bit

THS4140/1 ±15 V, 160 MHz, 450 V/μs, 6.5 nV/√Hz

operation through 40 MHz. Package options include

the SOIC-8 and the MSOP-8 with PowerPAD™ for a

THS4150/1 ±15 V, 150 MHz, 650 V/μs, 7.6 nV/√Hz

smaller footprint, enhanced ac performance, and

improved thermal dissipation capability. (1) Even-numbered devices feature power-down capability.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2PowerPAD is a trademark of Texas Instruments, Incorporated.

3All other trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (48 pages)

PAGE 1
DGN-8 DGK-8 THS4500 THS4501 D-8 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.
PAGE 2
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure.
PAGE 3
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.
PAGE 4
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS: VS = ±5 V RF = RG = 392 Ω, RL = 800 Ω, G = +1, and single-ended input, unless otherwise noted. THS4500 AND THS4501 PARAMETER TEST CONDITIONS TYP +25°C OVER TEMPERATURE +25°C 0°C to +70°C –40°C to +85°C UNITS MIN/ TYP/ MAX AC PERFORMANCE G = +1, PIN = –20 dBm, RF = 392 Ω 370 MHz Typ G = +2, PIN = –30 dBm, RF = 1 kΩ 175 MHz Typ G = +5, PIN = –30 dBm, RF = 2.
PAGE 5
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS: VS = ±5 V (continued) RF = RG = 392 Ω, RL = 800 Ω, G = +1, and single-ended input, unless otherwise noted. THS4500 AND THS4501 PARAMETER TEST CONDITIONS TYP +25°C OVER TEMPERATURE +25°C 0°C to +70°C –40°C to +85°C UNITS MIN/ TYP/ MAX OUTPUT COMMON-MODE VOLTAGE CONTROL Small-signal bandwidth RL = 400 Ω 180 MHz Typ Slew rate 2 VPP Step 92 V/μs Typ 0.
PAGE 6
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS: VS = 5 V RF = RG = 392 Ω, RL = 800 Ω, G = +1, and single-ended input, unless otherwise noted. THS4500 AND THS4501 PARAMETER TEST CONDITIONS TYP +25°C OVER TEMPERATURE +25°C 0°C to +70°C –40°C to +85°C UNITS MIN/T YP/M AX AC PERFORMANCE G = +1, PIN = –20 dBm, RF = 392 Ω 320 MHz Typ G = +2, PIN = –30 dBm, RF = 1 kΩ 160 MHz Typ G = +5, PIN = –30 dBm, RF = 2.
PAGE 7
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS: VS = 5 V (continued) RF = RG = 392 Ω, RL = 800 Ω, G = +1, and single-ended input, unless otherwise noted. THS4500 AND THS4501 PARAMETER TEST CONDITIONS TYP +25°C OVER TEMPERATURE +25°C 0°C to +70°C –40°C to +85°C UNITS MIN/T YP/M AX OUTPUT COMMON-MODE VOLTAGE CONTROL Small-signal bandwidth RL = 400 Ω 180 MHz Typ Slew rate 2 VPP Step 80 V/μs Typ 0.
PAGE 8
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS Table of Graphs (±5 V) FIGURE Small-signal unity-gain frequency response 1 Small-signal frequency response 2 0.
PAGE 9
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com Table of Graphs (5 V) FIGURE Small-signal unity-gain frequency response 51 Small-signal frequency response 52 0.
PAGE 10
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: ±5 V SMALL-SIGNAL FREQUENCY RESPONSE 1 22 0.5 20 0.3 −1 −1.5 −2 Gain = 1 RL = 800 Ω Rf = 392 Ω PIN = −20 dBm VS = ±5 V −2.5 −3 0.2 1 14 Gain = 5, Rf = 2.4 kΩ 12 10 8 4 RL = 800 Ω PIN = −30 dBm 0 VS = ±5 V −2 0.1 1 10 100 1000 100 HARMONIC DISTORTION vs FREQUENCY HARMONIC DISTORTION vs FREQUENCY 1 −30 −40 −50 −60 −70 HD2 −80 10 100 −100 0.
PAGE 11
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: ±5 V (continued) HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING 0 Differential Input to Differential Output Gain = 1 RL = 800 Ω Rf = 499 Ω f= 8 MHz VS = ±5 V −20 −30 −40 −50 −60 −70 HD2 −80 −90 HD3 −30 −40 −50 −60 HD2 −70 −80 HD3 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0.5 1 1.5 2 2.5 3 3.5 4 4.5 2.5 3 3.5 4 4.
PAGE 12
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: ±5 V (continued) HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING 0 Single-Ended Input to Differential Output Gain = 2 RL = 800 Ω Rf = 1 kΩ f= 30 MHz VS = ±5 V −20 −30 −40 −50 HD2 −60 −70 −80 −20 HD3 −30 −40 −50 −60 HD2 −80 HD3 −30 −40 −50 −60 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 −80 0 0.5 1 1.5 2 2.5 3 3.5 4 4.
PAGE 13
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: ±5 V (continued) SMALL-SIGNAL TRANSIENT RESPONSE 1.5 0.3 Gain = 1 RL = 800 Ω Rf = 499 Ω tr/tf = 300 ps VS = ±5 V 0.5 0 −0.5 −1 0 100 200 −0.1 −0.2 300 400 500 1.5 1 1 0.5 0 0 −1 −0.5 −2 −1 −3 −1.5 −4 −2 0 100 200 300 400 −2.5 0 500 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 t − Time − µs t − Time − ns Figure 29. Figure 30.
PAGE 14
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: ±5 V (continued) INPUT BIAS AND OFFSET CURRENT vs CASE TEMPERATURE RL = 800 Ω VS = ±5 V Open-Loop Gain − dB 56 55 54 53 52 51 50 35 0 VS = ±5 V 3.3 I IB − Input Bias Current − µ A 57 IIB− −0.01 −0.02 3.2 IIB+ 3.1 −0.03 3 −0.04 2.9 −0.05 2.8 −0.06 IOS 2.7 −0.07 2.6 −0.08 TA = 85°C 30 Quiescent Current − mA 3.
PAGE 15
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: ±5 V (continued) QUIESCENT CURRENT vs POWER-DOWN VOLTAGE TURN-ON AND TURN-OFF DELAY TIME 30 800 15 10 5 0 0.01 Current 0 0 −1 −2 −3 Quiescent Current − mA Powerdown Voltage Signal − V 20 0.02 −4 −5 −5 0 0.5 1 1.5 2 2.5 3 100.5 101 t − Time − ms Power-Down Voltage − V Figure 46. 102 700 600 500 400 300 Gain = 1 RL = 800 Ω Rf = 392 Ω PIN = −1 dBm VS = ±5 V 200 100 0 0.1 −6 −5 −4.5 −4 −3.
PAGE 16
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: 5 V SMALL-SIGNAL UNITY-GAIN FREQUENCY RESPONSE SMALL-SIGNAL FREQUENCY RESPONSE 1 0.2 22 Gain = 10, Rf = 5.1 kΩ −2 Gain = 1 RL = 800 Ω Rf = 392 Ω PIN = −20 dBm VS = 5 V −3 0.1 1 16 Gain = 5, Rf = 2.4 kΩ 14 12 10 8 Gain = 2, Rf = 1 kΩ 6 4 2 10 100 0 −2 0.1 1000 f − Frequency − MHz RL = 800 Ω PIN = −30 dBm VS = 5 V 1 0 Rf = 392 Ω −0.1 −0.2 −0.3 Gain = 1 RL = 800 Ω PIN = −20 dBm VS = 5 V −0.
PAGE 17
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: 5 V (continued) HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING 0 Differentia Input to Differential Output Gain = 1 RL = 800 Ω Rf = 392 Ω f= 8 MHz VS = 5 V −20 −30 −40 −50 −60 HD3 −70 −80 HD2 −90 −100 0 0.5 1 1.5 2 2.5 −20 −30 −40 HD2 −60 −70 −80 −20 −30 −40 −70 −80 −90 −100 1 1.5 2 2.
PAGE 18
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: 5 V (continued) HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING −40 −50 HD2 −60 HD3 −70 −80 30 40 HD2 50 −20 60 HD3 70 80 −30 −40 −60 −80 −90 −100 100 −100 1 1.5 2 2.5 3 2.5 0 3 400 800 1200 1600 RL − Load Resistance − Ω Figure 70. Figure 71.
PAGE 19
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: 5 V (continued) REJECTION RATIOS vs FREQUENCY VOLTAGE AND CURRENT NOISE vs FREQUENCY 90 60 50 CMMR PSRR− 40 30 20 In 10 0.1 1 10 100 1000 0.
PAGE 20
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: 5 V (continued) 0 150 VS = 5 V VS = 5 V 90 Source 100 Output Drive − mA 80 70 60 50 40 30 50 0 −50 20 −100 10 0 −10 0 1 2 3 4 Sink 5 −20 −30 −40 −50 HD3-SE and Diff −60 −70 −80 −90 HD2-SE 1 1.25 1.5 1.75 2 2.25 2.5 2.75 3 3.25 3.5 Input Common-Mode Range − V Case Temperature − °C VOCM − Output Common-Mode Voltage − V Figure 87. Figure 88. Figure 89.
PAGE 21
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS: 5 V (continued) POWER-DOWN QUIESCENT CURRENT vs SUPPLY VOLTAGE Power-Down Quiescent Current − µ A 1000 900 800 700 600 500 400 300 200 100 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 VS − Supply Voltage − V Figure 96.
PAGE 22
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com APPLICATION INFORMATION FULLY DIFFERENTIAL AMPLIFIERS FULLY DIFFERENTIAL AMPLIFIER TERMINAL FUNCTIONS Differential signaling offers a number of performance advantages in high-speed analog signal processing systems, including immunity to external common-mode noise, suppression of even-order nonlinearities, and increased dynamic range.
PAGE 23
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com RF1 RG1 RS +VS RT VS V OUT) + V OUT– VOCM + - + RG2 RF2 Figure 98. Application Circuit for the THS4500 and THS4501, Featuring Single-Supply Operation With a Ground-Reference Input Signal VS VOCM Where: RG β+ RF ) RG (4) V P + V IN)(1–β) ) V OUT–β NOTE: The equations denote the device inputs as VN and VP, and the circuit inputs as VIN+ and VIN–.
PAGE 24
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com Table 2. Midrail Referenced Gain (V/V) VIN+ (V) VIN– (V) VIN (VPP) VOCM (V) VOD (VPP) VNMIN (V) VNMAX (V) 1 0.5 to 4.5 2.5 4 2.5 4 2 3 2 1.5 to 3.5 2.5 2 2.5 4 2.16 2.83 4 2.0 to 3.0 2.5 1 2.5 4 2.3 2.7 8 2.25 to 2.75 2.5 0.5 2.5 4 2.389 2.61 CHOOSING THE PROPER VALUE FOR THE FEEDBACK AND GAIN RESISTORS The selection of feedback and gain resistors impacts circuit performance in a number of ways.
PAGE 25
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com For more detailed information about balance in fully differential amplifiers, see the application report, Fully Differential Amplifiers (SLOA054), referenced at the end of this data sheet. INTERFACING TO AN ANALOG-TO-DIGITAL CONVERTER The THS4500 family of amplifiers are designed specifically to interface to today's highest-performance ADCs.
PAGE 26
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com CF RS VS RG CG RS RF RF 15 V RT VS 5V RT RG RISO + VOCM 0.1 mF + VOCM + 1 mF THS4503 RL + - 0.1 mF RISO RISO CS VDD THS4500/2 5V 10 mF - RISO IN ADS5410 12-Bit/80 MSPS IN CM RF RG CS VOD = 26 VPP CG 5 V RG 10 mF 0.1 mF 0.1 mF RF Figure 104. Fully Differential Line Driver With High Output Swing CF Figure 102. Using the THS4503 With the ADS5410 CF RS VS RG RF 5V RT 5V 10 mF 0.
PAGE 27
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com detrimental effect on the distortion performance. The preferred method of filtering is to use the feedback network, as the typically smaller capacitances required at these points in the circuit do not load the amplifier nearly as heavily in the passband.
PAGE 28
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com The THS4500 family of fully differential amplifiers contains devices that come with and without the power-down option. Even-numbered devices have power-down capability, which is described in detail here. The power-down pin of the amplifiers defaults to the positive supply voltage in the absence of an applied voltage (that is, an internal pull-up resistor is present), putting the amplifier in the power-on mode of operation.
PAGE 29
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 design decisions. Traditionally, these systems use primarily class-A, single-ended RF amplifiers as gain blocks. These RF amplifiers are typically designed to operate in a 50-Ω environment, just like the rest of the receiver chain. Since intercept points are given in dBm, this implies an associated impedance (50 Ω). However, with a fully differential amplifier, the output does not require termination as an RF amplifier would.
PAGE 30
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 Ni eg NA Rg www.ti.com ef Rf Si Scaling Factors for Individual Noise Sources Asseming No Termination Resistance is Used (that is, RT is Open) en Ni No Rs + Rt So fully-diff amp − ini es NA: Fully Differential Amplifier; termination = 2Rg Noise Source No et eg (ini)2 Rg Rf ef ȡR ) ȧR R Ȣ (iii)2 f s 2 (18) (19) Rg2 (20) ǒ Ǔ Rg Rf 2 Figure 111.
PAGE 31
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com PRINTED CIRCUIT BOARD LAYOUT TECHNIQUES FOR OPTIMAL PERFORMANCE Achieving optimum performance with high frequency amplifier-like devices in the THS4500 family requires careful attention to PCB layout parasitic and external component types. Recommendations that optimize performance include: • Minimize parasitic capacitance to any ac ground for all of the signal I/O pins.
PAGE 32
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com the THS4500 family parts directly onto the board. 0.205 PowerPAD DESIGN CONSIDERATIONS The THS4500 family is available in a thermally-enhanced PowerPAD set of packages. These packages are constructed using a downset leadframe upon which the die is mounted [see Figure 112(a) and Figure 112(b)]. This arrangement results in the lead frame being exposed as a thermal pad on the underside of the package [see Figure 112(c)].
PAGE 33
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com POWER DISSIPATION AND THERMAL CONSIDERATIONS The THS4500 family of devices does not incorporate automatic thermal shutoff protection, so the designer must take care to ensure that the design does not violate the absolute maximum junction temperature of the device. Failure may result if the absolute maximum junction temperature of +150°C is exceeded. For best performance, design for a maximum junction temperature of +125°C.
PAGE 34
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com RF VS RG RS RISO + VS RT - - CL + THS4501 product folder on the Texas Instruments web site, www.ti.com, or through your local Texas Instruments sales representative. A schematic for the evaluation board is shown in Figure 116 with the default component values. Unpopulated footprints are shown to provide insight into design flexibility. RISO -VS C4 Riso = 10 - 25 W RF R0805 VS RG J1 Figure 115.
PAGE 35
THS4500 THS4501 SLOS350F – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ADDITIONAL REFERENCE MATERIAL • • • • • • • PowerPAD Made Easy, application brief, Texas Instruments Literature Number SLMA004. PowerPAD Thermally-Enhanced Package, technical brief, Texas Instruments Literature Number SLMA002. Karki, James. Fully Differential Amplifiers. application report, Texas Instruments Literature Number SLOA054D. Karki, James.
PAGE 36
PACKAGE OPTION ADDENDUM www.ti.
PAGE 37
PACKAGE OPTION ADDENDUM www.ti.
PAGE 38
PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses.
PAGE 39
PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant THS4500CDGNR MSOPPower PAD DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 THS4500IDGNR MSOPPower PAD DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 THS4501IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.
PAGE 40
PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) THS4500CDGNR MSOP-PowerPAD DGN 8 2500 358.0 335.0 35.0 THS4500IDGNR MSOP-PowerPAD DGN 8 2500 358.0 335.0 35.0 THS4501IDR SOIC D 8 2500 367.0 367.0 35.
PAGE 41
PAGE 42
PAGE 43
PAGE 44
PAGE 45
PAGE 46
PAGE 47
PAGE 48
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.