Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Op-amp, differential amplifier Differential MSOP 8 PowerPad

IN-

IN+

OCM

S+

OUT+

S-

OUT-

THS4502

THS4503

www.ti.com

SLOS352E –APRIL 2002–REVISED OCTOBER 2011

Wideband, Low-Distortion Fully Differential Amplifiers

Check for Samples: THS4502, THS4503

FEATURES

DESCRIPTION

The THS4502 and THS4503 are high-performance

• Fully Differential Architecture

fully differential amplifiers from Texas Instruments.

• Bandwidth: 370 MHz

The THS4502, featuring power-down capability, and

• Slew Rate: 2800 V/µs

the THS4503, without power-down capability, set new

performance standards for fully differential amplifiers

• IMD

: -95 dBc at 30 MHz

with unsurpassed linearity, supporting 14-bit

• OIP

: 51 dBm at 30 MHz

operation through 40 MHz. Package options include

• Output Common-Mode Control

the 8-pin SOIC and the 8-pin MSOP with

PowerPAD™ for a smaller footprint, enhanced ac

• Wide Power Supply Voltage Range: 5 V, ±5 V,

performance, and improved thermal dissipation

12 V, 15 V

capability.

• Centered Input Common-Mode Range

• Power-Down Capability (THS4502)

• Evaluation Module Available

APPLICATIONS

• High Linearity Analog-to-Digital Converter

Preamplifier

• Wireless Communication Receiver Chains

RELATED DEVICES

• Single-Ended to Differential Conversion

DEVICE

(1)

DESCRIPTION

• Differential Line Driver

THS4500/1 370 MHz, 2800 V/µs, V

ICR

Includes V

S–

• Active Filtering of Differential Signals

THS4502/3 370 MHz, 2800 V/µs, Centered V

ICR

THS4120/1 3.3 V, 100 MHz, 43 V/µs, 3.7 nV√Hz

THS4130/1 ±15 V, 150 MHz, 51 V/µs, 1.3 nV√Hz

THS4140/1 ±15 V, 160 MHz, 450 V/µs, 6.5 nV√Hz

THS4150/1 ±15 V, 150 MHz, 650 V/µs, 7.6 nV√Hz

(1) Even numbered devices feature power-down capability.

WARNING

The THS4502 and THS4503 may have low-level oscillation when the die

temperature (also known as the junction temperature) exceeds +60°C. These

devices are not recommended for new designs where the die temperature is

expected to exceed +60°C. For more information, see Maximum Die Temperature

to Prevent Oscillation section.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2PowerPAD is a trademark of Texas Instruments.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (49 pages)

PAGE 1
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com Wideband, Low-Distortion Fully Differential Amplifiers Check for Samples: THS4502, THS4503 FEATURES DESCRIPTION • • • • • • • The THS4502 and THS4503 are high-performance fully differential amplifiers from Texas Instruments.
PAGE 2
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure.
PAGE 3
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) UNIT Supply voltage, VS 16.
PAGE 4
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS VS = ±5 V Rf = Rg = 499Ω , RL = 800 Ω, G = +1, Single-ended input unless otherwise noted. THS4502 AND THS4503 PARAMETER TEST CONDITIONS OVER TEMPERATURE (1) TYP 25°C 25°C 0°C to 70°C -40°C to 85°C UNITS MIN/ TYP/ MAX AC PERFORMANCE G = +1, PIN = -20 dBm, Rf = 392 Ω 370 MHz Typ G = +2, PIN = -30 dBm, Rf = 1 kΩ 175 MHz Typ G = +5, PIN = -30 dBm, Rf = 1.
PAGE 5
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS VS = ±5 V (continued) Rf = Rg = 499Ω , RL = 800 Ω, G = +1, Single-ended input unless otherwise noted. THS4502 AND THS4503 PARAMETER TEST CONDITIONS OVER TEMPERATURE (1) TYP 25°C 0°C to 70°C 25°C -40°C to 85°C UNITS MIN/ TYP/ MAX OUTPUT COMMON-MODE VOLTAGE CONTROL Small-signal bandwidth RL = 400Ω 180 MHz Typ Slew rate 2 VPP step 87 V/µs Typ 0.98 V/V Min Minimum gain 1 0.98 0.
PAGE 6
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS VS = 5 V (continued) Rf = Rg = 499 Ω, RL = 800 Ω, G = +1, Single-ended input unless otherwise noted. THS4502 AND THS4503 PARAMETER UNITS 8.3 ns Typ f = 8 MHz, -81 dBc Typ f = 30 MHz -60 dBc Typ 25°C Settling time to 0.
PAGE 7
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS VS = 5 V (continued) Rf = Rg = 499 Ω, RL = 800 Ω, G = +1, Single-ended input unless otherwise noted. THS4502 AND THS4503 PARAMETER TEST CONDITIONS OVER TEMPERATURE (1) TYP 25°C 25°C 0°C to 70°C -40°C to 85°C UNITS MIN/T YP/M AX POWER DOWN (THS4502 ONLY) Enable voltage threshold Device enabled ON above 2.1 V 2.1 V Min Disable voltage threshold Device disabled OFF below 0.7 V 0.
PAGE 8
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS Table of Graphs (±5 V) FIGURE Small signal unity gain frequency response 1 Small signal frequency response 2 0.
PAGE 9
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com Table of Graphs (5 V) FIGURE Small signal unity gain frequency response 50 Small signal frequency response 51 0.
PAGE 10
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS (±5 V Graphs) 22 20 18 0 -0.5 -1 -1.5 -2 Gain = 1 RL = 800 Ω Rf = 392 Ω PIN = -20 dBm VS = ±5 V -3 -3.5 1 0.1 16 12 10 8 Gain = 2, Rf = 1 kΩ 6 4 RL = 800 Ω PIN = -30 dBm VS = ±5 V 0 -2 0.1 10 100 0 Gain = 5, Rf = 1.3 kΩ 14 2 -4 0.1 Gain = 10, Rf = 1.3 kΩ 0.1 dB Gain Flatness - dB 1 0.5 -2.5 0.
PAGE 11
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.
PAGE 12
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS (±5 V Graphs) (continued) 0 Differential Input to Differential Output Gain = 2 RL = 800 Ω Rf = 1.3 kΩ f= 8 MHz VS = ±5 V -30 -40 -50 -20 Harmonic Distortion - dBc HD3 -60 HD2 -70 -80 -30 -40 -50 -60 HD2 -70 -80 -90 1 2 3 4 5 6 7 8 9 10 -40 -50 -60 HD2 -70 -80 HD3 -100 0 400 800 1200 0 1600 Figure 19. Figure 20.
PAGE 13
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS (±5 V Graphs) (continued) OVERDRIVE RECOVERY Gain = 1 RL = 800 Ω Rf = 499 Ω tr/tf = 300 ps VS = ±5 V 0.1 0 -0.1 -0.2 -0.3 -0.4 -100 3 2 0.5 0 0 -1 -0.5 -2 -1 -3 -1.5 -4 -2 100 200 300 400 -2.5 0 500 4 2 -1 -4 -2 Figure 30. REJECTION RATIOS vs FREQUENCY REJECTION RATIOS vs CASE TEMPERATURE 100 PSRR+ 80 Hz Hz 50 CMMR PSRR- 40 30 20 10 100 1000 0.
PAGE 14
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS (±5 V Graphs) (continued) 0.14 IIB- 1.75 0.12 1.5 0.11 IIB+ 1.25 0.1 1 0.09 IOS 0.08 0.75 0.5 0.07 0.25 0.06 35 2.5 VS = ±5 V TA = 85°C 30 VOS - Input Offset Voltage - mV I IB - Input Bias Current - µ A 0.13 Quiescent Current - mA VS = ±5 V 2 I OS - Input Offset Current - µ A 2.
PAGE 15
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS (±5 V Graphs) (continued) TURNON AND TURNOFF DELAY TIMES SINGLE-ENDED OUTPUT IMPEDANCE IN POWER DOWN vs FREQUENCY 0.02 0 0 -1 -2 -3 -4 -5 -6 0 0.5 1 1.5 2 2.5 3 100.5 101 t - Time - ms 102 103 1000 900 800 700 600 500 400 Gain = 1 RL = 800 Ω Rf = 392 Ω PIN = -1 dBm VS = ±5 V 300 200 100 0 0.1 1.4 1.2 RL = 800 Ω VS = ±5 V 1 0.8 0.6 0.4 0.
PAGE 16
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS (5 V GRAPHS) SMALL SIGNAL FREQUENCY RESPONSE SMALL SIGNAL UNITY GAIN FREQUENCY RESPONSE 0.1 dB GAIN FLATNESS FREQUENCY RESPONSE 22 Gain = 10, Rf = 1.3 kΩ 20 1 0.2 -1 -2 Gain = 1 RL = 800 Ω Rf = 392 Ω PIN = -20 dBm VS = 5 V 14 12 10 8 6 1 RL = 800 Ω PIN = -30 dBm VS = 5 V 2 0 -2 0.1 -4 0.1 Gain = 2, Rf = 1 kΩ 4 10 100 0 -0.1 Rf = 392 Ω -0.2 -0.
PAGE 17
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS (5 V GRAPHS) (continued) HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING 0 Differential Input to Differential Output Gain = 1 RL = 800 Ω Rf = 499 Ω f= 8 MHz VS = 5 V -30 -40 -50 Harmonic Distortion - dBc -20 0 Differential Input to Differential Output Gain = 1 RL = 800 Ω Rf = 499 Ω f= 30 MHz VS = 5 V -10 HD3 -60 -70 -80 -20 -30 -40 -50 HD3 -60 HD2 -70 -80 HD2 -90 -90 -100 0.5 1 1.5 2 2.5 3 3.
PAGE 18
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS (5 V GRAPHS) (continued) HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING HARMONIC DISTORTION vs LOAD RESISTANCE 0 Differential Input to Differential Output Gain = 2 RL = 800 Ω Rf = 1.3 kΩ f= 8 MHz VS = 5 V -30 -40 -50 Harmonic Distortion - dBc HD3 -60 HD2 -70 -80 -20 -30 -40 -50 HD2 -60 HD3 -70 -80 -20 -30 -40 -50 -80 -90 -90 -100 -100 1 1.5 2 2.5 3 3.5 4 4.5 5 0 400 Figure 68.
PAGE 19
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS (5 V GRAPHS) (continued) OPEN-LOOP GAIN AND PHASE vs FREQUENCY 60 -20 PIN = -30 dBm RL = 800 Ω Rf = 100 kΩ VS = 5 V 50 Open-Loop Gain - dB -10 30 Gain PIN = -20 dBm RL = 800 Ω Rf = 499 Ω VS = 5 V -30 -40 -50 57 55 40 -30 30 -60 Phase 20 -90 10 -120 54 53 52 51 50 49 48 -60 47 0 0.01 -70 1 10 f - Frequency - MHz 100 0.1 1 Case Temperature - °C 0.12 0.11 IIB+ 1.25 0.1 0.09 1 IOS 0.
PAGE 20
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com TYPICAL CHARACTERISTICS (5 V GRAPHS) (continued) OUTPUT OFFSET VOLTAGE vs OUTPUT COMMON-MODE VOLTAGE 3 Gain = 1 RL = 800 Ω Rf = 499 Ω PIN= -20 dBm VS = 5 V 1 800 25 600 0 -1 20 400 200 0 -200 -400 -2 15 10 5 -600 -3 10 100 1000 -800 0 0.5 1 0.03 -1 -2 -3 -4 -5 -6 0 0.5 1 1.5 2 2.5 3 100.5 101 t - Time - ms 102 103 3 3.5 4 4.5 0 5 0 0.25 0.5 0.75 1 1.25 1.5 1.75 2 2.25 2.
PAGE 21
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com APPLICATION INFORMATION MAXIMUM DIE TEMPERATURE TO PREVENT OSCILLATION The THS4502 and THS4503 may have low level oscillation when the die temperature (also called junction temperature) exceeds +60°C and is not recommended for new designs where the die temperature is expected to exceed +60°C. 10V, RL = 800 Ω differential, and the quiescent current = 32mA (the maximum over 0°C to 70°C temperature range).
PAGE 22
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com FULLY DIFFERENTIAL AMPLIFIER TERMINAL FUNCTIONS Fully differential amplifiers are typically packaged in eight-pin packages as shown in the diagram. The device pins include two inputs (VIN+,VIN-), two outputs (VOUT-,VOUT+), two power supplies (VS+, VS-), an output common-mode control pin (VOCM), and an optional power-down pin (PD).
PAGE 23
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com Table 2. Negative-Rail Referenced (continued) V N + V IN–(1–β) ) V OUT)β (3) RG β+ RF ) RG Where: (4) V P + V IN)(1–β) ) V OUT–β (5) VIN+ Vp VOCM VOUT- + - + Rg VIN (VPP) VOCM (V) VOD (VPP) VNMIN (V) VNMAX (V) Gain (V/V) VIN+ (V) VIN(V) VIN (VPP) VOCM (V) VOD (VPP) VNMIN (V) VNMAX (V) 1 0.5 to 4.5 2.5 4 2.5 4 2 3 2 1.5 to 3.5 2.5 2 2.5 4 2.16 2.83 4 2.0 to 3.0 2.5 1 2.5 4 2.3 2.7 8 2.
PAGE 24
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com APPLICATION CIRCUITS USING FULLY DIFFERENTIAL AMPLIFIERS β1 + Fully differential amplifiers provide designers with a great deal of flexibility in a wide variety of applications. This section provides an overview of some common circuit configurations and gives some design guidelines.
PAGE 25
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com • • • • • • common-mode voltage control. Do not terminate the output unless required. Many open-loop, class-A amplifiers require 50-Ω termination for proper operation, but closed-loop fully differential amplifiers drive a specific output voltage regardless of the load impedance present. Terminating the output of a fully differential amplifier with a heavy load adversely effects the amplifier's linearity.
PAGE 26
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 CG RS Rg SETTING THE OUTPUT COMMON-MODE VOLTAGE WITH THE VOCM INPUT Rf 15 V RT VS Riso VOCM www.ti.com + - - RL VDD THS4500/2 0.1 µF + Riso Rf Rg CS CS VOD = 26 VPP CG Fully Differential Line Driver With High Output Swing Figure 99. Filtering With Fully Differential Amplifiers Similar to their single-ended counterparts, fully differential amplifiers have the ability to couple filtering functionality with voltage gain.
PAGE 27
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com specific source of electromagnetic or radio frequency interference is present elsewhere in the system. Information on the ac performance (bandwidth, slew rate) of the VOCM circuitry is included in the specification table and graph section. Since the VOCM pin provides the ability to set an output common-mode voltage, the ability for increased power dissipation exists.
PAGE 28
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 PO www.ti.com PO Power ∆fc = fc - f1 ∆fc = f2 - fc IMD3 = PS - PO PS fc - 3∆f PS f1 fc f2 However, with a fully differential amplifier, the output does not require termination as an RF amplifier would. Because closed-loop amplifiers deliver signals to their outputs regardless of the impedance present, it is important to comprehend this when evaluating the intercept point of a fully differential amplifier.
PAGE 29
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com OIP 3 - Third-Order Output Intercept Point - dBm THIRD-ORDER OUTPUT INTERCEPT POINT vs FREQUENCY Ni eg NA Rg Rf ef 60 Normalized to 200 Ω 55 Si Normalized to 50 Ω 50 en Ni 45 No Rs + 40 Rt 35 OIP3 RL= 800 Ω es 30 20 i ii 15 0 No et Gain = 1 Rf = 392 Ω VS = ± 5 V Tone Spacing = 200 kHz 25 So fully-diff amp - i ni eg 10 20 30 40 50 60 70 80 90 100 Rg Rf ef f - Frequency - MHz Figure 105.
PAGE 30
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com PRINTED-CIRCUIT BOARD LAYOUT TECHNIQUES FOR OPTIMAL PERFORMANCE NA: Fully Differential Amplifier; termination = 2Rg Noise Source Scale Factor ȡR ) ȧR R Ȣ 2 (eni)2 f (ini)2 Rg2 (iii)2 Rg2 g (18) s 2 (19) (20) ǒ Ǔ Rg Rf 2 4kTRf ȣ Rȧ ) Ȥ Rg g 2 (21) 2 ȡ R ȣ ȧR ) R ȧ Ȣ 2Ȥ g 2 4kTRg (22) s g Figure 108. Scaling Factors for Individual Noise Sources Assuming No termination Resistance is Used (e.g.
PAGE 31
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com • • • • effect circuit operation. Keep resistor values as low as possible, consistent with load driving considerations. Connections to other wideband devices on the board may be made with short direct traces or through onboard transmission lines. For short connections, consider the trace and the input to the next device as a lumped capacitive load.
PAGE 32
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com 1. Prepare the PCB with a top side etch pattern as shown in Figure 113. There should be etch for the leads as well as etch for the thermal pad. 2. Place five holes in the area of the thermal pad. These holes should be 13 mils in diameter. Keep them small so that solder wicking through the holes is not a problem during reflow. 3. Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area.
PAGE 33
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com dissipation, but also dynamic power dissipation. Often times, this is difficult to quantify because the signal pattern is inconsistent, but an estimate of the RMS power dissipation can provide visibility into a possible problem. DRIVING CAPACITIVE LOADS High-speed amplifiers are typically not well-suited for driving large capacitive loads.
PAGE 34
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com ADDITIONAL REFERENCE MATERIAL • • • • • • • 34 PowerPAD Made Easy, application brief, Texas Instruments Literature Number SLMA004. PowerPAD Thermally Enhanced Package, technical brief, Texas Instruments Literature Number SLMA002. Karki, James. Fully Differential Amplifiers.application report, Texas Instruments Literature Number SLOA054D. Karki, James.
PAGE 35
THS4502 THS4503 SLOS352E – APRIL 2002 – REVISED OCTOBER 2011 www.ti.com REVISION HISTORY Changes from Revision D (January 2004) to Revision E Page • Added WARNING to DESCRIPTION ................................................................................................................................... 1 • Added Maximum junction temperature to prevent oscillation, TJ and footnote to ABSOLUTE MAXIMUM RATINGS ........ 3 • Deleted power rating and footnote from PACKAGE DISSIPATION RATINGS ......
PAGE 36
PACKAGE OPTION ADDENDUM www.ti.
PAGE 37
PACKAGE OPTION ADDENDUM www.ti.
PAGE 38
PACKAGE OPTION ADDENDUM www.ti.com 31-Oct-2013 ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
PAGE 39
PACKAGE OPTION ADDENDUM www.ti.
PAGE 40
PACKAGE MATERIALS INFORMATION www.ti.com 12-Aug-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant THS4502CDGNR MSOPPower PAD DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 THS4502IDGNR MSOPPower PAD DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 THS4502IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.
PAGE 41
PACKAGE MATERIALS INFORMATION www.ti.com 12-Aug-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) THS4502CDGNR MSOP-PowerPAD DGN 8 2500 358.0 335.0 35.0 THS4502IDGNR MSOP-PowerPAD DGN 8 2500 358.0 335.0 35.0 THS4502IDR SOIC D 8 2500 367.0 367.0 35.0 THS4503CDGNR MSOP-PowerPAD DGN 8 2500 358.0 335.0 35.0 THS4503CDR SOIC D 8 2500 367.0 367.0 35.0 THS4503IDGNR MSOP-PowerPAD DGN 8 2500 358.
PAGE 42
PAGE 43
PAGE 44
PAGE 45
PAGE 46
PAGE 47
PAGE 48
PAGE 49
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.