Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Op-amp Variable gain HTSSOP 14

Table Of Contents

0.1 Fm

33pF

0.1 Fm

0.1 Fm0.1 Fm 6.8 Fm

0.1 Fm

33pF

1kW 1kW

24.9 W

24.9 W24.9 W

24.9 W

THS7530

AGCDetect

REF

OUT+

IN-

OUT-

IN+

S-

G-

CL-

CL+

OCM

G+

S+

=5V

THS7530

www.ti.com

SLOS405C –DECEMBER 2002–REVISED FEBRUARY 2010

HIGH-SPEED, FULLY DIFFERENTIAL, CONTINUOUSLY

VARIABLE GAIN AMPLIFIER

Check for Samples: THS7530

FEATURES

DESCRIPTION

• Low Noise: V

= 1.1 nV/√Hz,

Noise Figure = 9 dB

The THS7530 is fabricated using Texas Instruments'

state-of-the-art BiCom III SiGe complementary bipolar

• Low Distortion:

process. The THS7530 is a dc-coupled, wide

– - HD

= -65 dBc, HD

= -61 dBc at 32 MHz

bandwidth amplifier with voltage-controlled gain. The

– - IMD

= -62 dBc, OIP

= 21 dBm at 70 MHz

amplifier has high-impedance differential inputs and

• 300 MHz Bandwidth low-impedance differential outputs with high

bandwidth gain control, output common-mode control,

• Continuously Variable Gain Range: 11.6 dB

and output voltage clamping.

to 46.5 dB

Signal channel performance is exceptional with

• Gain Slope: 38.8 dB/V

300-MHz bandwidth, and third harmonic distortion of

• Fully Differential Input and Output

–61 dBc at 32 MHz with 1-V

output into 400 Ω.

• Output Common-Mode Voltage Control

Gain control is linear in dB with 0 V to 0.9 V varying

• Output Voltage Limiting

the gain from 11.6 dB to 46.5 dB with 38.8-dB/V gain

slope.

APPLICATIONS

Output voltage limiting is provided to limit the output

• Time Gain Amplifiers in Ultra Sound, Sonar,

voltage swing, and prevent saturating following

and Radar

stages.

• Automatic Gain Control in Communication

The device is characterized for operation over the

and Video

industrial temperature range, –40°C to +85°C.

• System Gain Calibration in Communications

• Variable Gain in Instrumentation

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2PowerPAD is a trademark of Texas Instruments.

3All other trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (24 pages)

PAGE 1
THS7530 www.ti.com SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 HIGH-SPEED, FULLY DIFFERENTIAL, CONTINUOUSLY VARIABLE GAIN AMPLIFIER Check for Samples: THS7530 FEATURES 1 • 23 • • • • • • • DESCRIPTION Low Noise: Vn = 1.1 nV/√Hz, Noise Figure = 9 dB Low Distortion: – - HD2 = -65 dBc, HD3 = -61 dBc at 32 MHz – - IMD3 = -62 dBc, OIP3 = 21 dBm at 70 MHz 300 MHz Bandwidth Continuously Variable Gain Range: 11.6 dB to 46.5 dB Gain Slope: 38.
PAGE 2
THS7530 SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure.
PAGE 3
THS7530 www.ti.com SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 SPECIFICATIONS: MAIN AMPLIFIER VS+ = 5 V, VS- = 0 V, VOCM = 2.5 V, VICM = 2.5 V, VG- = 0 V, VG+ = 1 V (maximum gain), TA = 25°C, ac performance measured using the ac test circuit shown in Figure 1 (unless otherwise noted).
PAGE 4
THS7530 SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 www.ti.com SPECIFICATIONS: MAIN AMPLIFIER (continued) VS+ = 5 V, VS- = 0 V, VOCM = 2.5 V, VICM = 2.5 V, VG- = 0 V, VG+ = 1 V (maximum gain), TA = 25°C, ac performance measured using the ac test circuit shown in Figure 1 (unless otherwise noted).
PAGE 5
THS7530 www.ti.com SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 VS+ = 5 V 1 kW 1 kW 0.1 mF 0.1 mF VCL+ 50-W Source Coax VIN VCL- 50 W 1:1 6.8 mF 33 pF 24.9 W 1:1 VOUT Coax 50-W Load THS7530 VOCM PD 24.9 W VG- 0.1 mF VS- VG+ 33 pF Figure 1. AC Test Circuit VS+ = 5 V VCL+ VCL- 0.1 mF 6.8 mF VOUT- VIN+ VOCM VIN- THS7530 800 W VOUT+ PD VG- 0.1 mF VSVG+ Figure 2.
PAGE 6
THS7530 SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 www.ti.com PIN ASSIGNMENTS TSSOP PACKAGE PWP-14 (TOP VIEW) VCL+ NC 1 14 NC 2 13 VCL- VIN+ 3 12 VIN- 4 11 VOUT- VG+ 5 10 VOUT+ VG- 6 9 VS+ PD 7 8 VS- VOCM Table 1. Terminal Functions TERMINAL 6 DESCRIPTION NO.
PAGE 7
THS7530 www.ti.com SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 TYPICAL CHARACTERISTICS Table of Graphs Measured using the ac test circuit shown in Figure 1 (unless otherwise noted).
PAGE 8
THS7530 SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 www.ti.com TYPICAL CHARACTERISTICS VOLTAGE GAIN TO LOAD vs FREQUENCY (PIN = –45 dBm) GAIN AND GAIN ERROR vs VG+ 50 0.4 45 40 Maximum Gain 0.2 40 0 30 30 Gain - dB Gain 20 25 -0.2 20 -0.4 15 10 Gain Error Minimum Gain 10 Gain is taken at load. Add 6 dB to refer to amplifier output. 5 -0.6 0 1 10 100 0 1000 200 400 Figure 3.
PAGE 9
THS7530 www.ti.
PAGE 10
THS7530 SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) VG+ INPUT IMPEDANCE vs FREQUENCY VOCM INPUT IMPEDANCE vs FREQUENCY COMMON-MODE REJECTION RATIO vs FREQUENCY 25 100 -10 20 VOCM - Input Impedance - kW VG+ - Input Impedance - kW 80 CMRR - Common-Mode Rejection Ratio - dB 90 70 60 50 40 30 20 15 10 5 -20 -30 -40 -50 10 0 -60 0 0.1 1 10 0.1 1 f - Frequency - MHz 10 0.1 100 Figure 14.
PAGE 11
THS7530 www.ti.com SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 APPLICATION INFORMATION The THS7530 is designed for nominal 5-V power supply from VS+ to VS–. Figure 20 through Figure 24 show some basic circuit configurations. The amplifier has fully differential inputs, VIN+ and VIN–, and fully differential outputs, VOUT+ and VOUT– The inputs are high impedance and outputs are low impedance. External resistors are recommended for impedance matching and termination purposes.
PAGE 12
THS7530 SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 www.ti.com VS+ = 5 V 1 kW TSSOP 14-Pin PWP Package 2´3 1 kW 0.1 mF 0.1 mF 49.9 W 6.8 mF 3.4 33 pF 49.9 W VCL+ VCL- 0.1 mF 24.9 W VIN VOUTVOCM THS7530 PD 5 VOUT+ 24.9 W VG- 0.1 mF 33 pF VS- VG+ Figure 23. DC-Coupled Single-Ended Input with DC-Coupled Differential Output VS+ = 5 V 1 kW 1 kW 0.1 mF 0.1 mF 24.9 W 6.8 mF 33 pF 24.9 W 24.9 W VOUTVOCM PD THS7530 VOUT+ VIN24.9 W VG- 0.1 mF 33 pF VS- VG+ Figure 24.
PAGE 13
THS7530 www.ti.com SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 SPICE MODEL * [Disclaimer] (C) Copyright Texas Instruments Incorporated 1999-2002 All rights reserved * Texas Instruments Incorporated hereby grants the user of this SPICE Macro-model a * non-exclusive, nontransferable license to use this SPICE Macro-model under the following * terms. Before using this SPICE Macro-model, the user should read this license.
PAGE 14
THS7530 SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 www.ti.com *FREQUENCY SHAPING* E3 131 0 329 0 1 R5 131 140 30 L3 140 133 7.5n C6 133 0 24p E4 130 0 328 0 1 R9 130 141 30 L4 141 125 10n C7 125 0 27p *OUTPUT BUFFER* Q9 4 133 117 PNP 5.12 Q10 3 133 127 NPN 5.12 Q11 3 117 134 NPN 81.92 Q12 4 127 135 PNP 81.92 Q13 4 125 116 PNP 5.12 Q14 3 125 126 NPN 5.12 Q15 3 116 136 NPN 81.92 Q16 4 126 137 PNP 81.92 R6 138 134 5 R7 135 138 5 R10 139 136 5 R11 137 139 5 I5 3 117 DC 0.4e-3 I6 127 4 DC 0.
PAGE 15
THS7530 www.ti.com SLOS405C – DECEMBER 2002 – REVISED FEBRUARY 2010 REVISION HISTORY Changes from Revision B (February, 2006) to Revision C Page • Corrected polarity indication on input and output in front-page figure .................................................................................. 1 • Deleted lead temperature specification from Absolute Maximum Ratings table .................................................................. 2 • Corrected Figure 2 .................................
PAGE 16
PACKAGE OPTION ADDENDUM www.ti.
PAGE 17
PACKAGE OPTION ADDENDUM www.ti.
PAGE 18
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device THS7530PWPR Package Package Pins Type Drawing SPQ HTSSOP 2000 PWP 14 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 330.0 12.4 Pack Materials-Page 1 6.9 B0 (mm) K0 (mm) P1 (mm) 5.6 1.6 8.0 W Pin1 (mm) Quadrant 12.
PAGE 19
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) THS7530PWPR HTSSOP PWP 14 2000 367.0 367.0 35.
PAGE 20
PAGE 21
PAGE 22
PAGE 23
PAGE 24
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.