TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 D D D D D D D D D D Very Low Power Consumption Typical Supply Current . . . 200 µA (Per Amplifier) Wide Common-Mode and Differential Voltage Ranges Low Input Bias and Offset Currents Common-Mode Input Voltage Range Includes VCC+ Output Short-Circuit Protection High Input Impedance . . .
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 TL061 . . .
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 symbol (each amplifier) IN+ + OUT – IN– OFFSET N1 OFFSET N2 Offset Null/Compensation TL061 Only schematic (each amplifier) VCC+ IN+ 50 Ω IN– 100 Ω C1 OFFSET N1 OFFSET N2 OUT VCC– TL061 Only C1 = 10 pF on TL061, TL062, and TL064 Component values shown are nominal.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 TL061Y chip information This chip, when properly assembled, has characteristics similar to the TL061. Thermal compression or ultrasonic bonding can be used on the doped-aluminum bonding pads. The chips can be mounted with conductive epoxy or a gold-silicon preform.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 TL062Y chip information This chip, when properly assembled, has characteristics similar to the TL062. Thermal compression or ultrasonic bonding can be used on the doped-aluminum bonding pads. The chips can be mounted with conductive epoxy or a gold-silicon preform.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 TL064Y chip information This chip, when properly assembled, has characteristics similar to the TL064. Thermal compression or ultrasonic bonding can be used on the doped-aluminum bonding pads. The chips can be mounted with conductive epoxy or a gold-silicon preform.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† TL06_C TL06_AC TL06_BC TL06_I TL06_M UNIT Supply voltage, VCC+ (see Note 1) 18 18 18 V Supply voltage, VCC– (see Note 1) –18 –18 –18 V Differential input voltage, VID (see Note 2) ±30 ±30 ±30 V V Input voltage, VI (s
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 electrical characteristics, VCC± = ±15 V (unless otherwise noted) PARAMETER TL061C TL062C TL064C TEST CONDITIONS† MIN TA = 25°C TA = Full range TYP MAX 3 15 VIO Input offset voltage VO = 0,, RS = 50 Ω αVIO Temperature coefficient of input offset voltage VO = 0,, RS = 50 Ω,, TA = Full range IIO Input offset curren
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 electrical characteristics, VCC± = ±15 V (unless otherwise noted) PARAMETER TL061BC TL062BC TL064BC TEST CONDITIONS† MIN TA = 25°C TA = Full range TYP MAX 2 3 VIO Input offset voltage VO = 0,, RS = 50 Ω αVIO Temperature coefficient of input offset voltage VO = 0, RS = 50 Ω, TA = Full range IIO Input offset curren
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 electrical characteristics, VCC± = ±15 V (unless otherwise noted) TL061M TL062M TEST CONDITIONS† PARAMETER MIN TA = 25°C TA = –55°C to 125°C VIO Input offset voltage VO = 0,, RS = 50 Ω αVIO Temperature coefficient of input offset voltage VO = 0, RS = 50 Ω, TA = –55°C to 125°C IIO Input offset current VO = 0 IIB V
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 electrical characteristics, VCC± = ±15 V, TA = 25°C (unless otherwise noted) TL061Y TL062Y TL064Y TEST CONDITIONS† PARAMETER MIN VIO αVIO Input offset voltage Temperature coefficient of input offset voltage VO = 0, VO = 0, IIO IIB Input offset current Input bias current‡ VO = 0 VO = 0 UNIT TYP MAX RS = 50 Ω 3 15
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 PARAMETER MEASUREMENT INFORMATION 10 kΩ – VI 1 kΩ – OUT + VI OUT RL = 2 kΩ + CL = 100 pF RL Figure 1. Unity-Gain Amplifier Figure 2. Gain-of-10 Inverting Amplifier – IN – TL061 OUT + IN + N2 N1 100 kΩ 1.5 kΩ VCC– Figure 3.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 TYPICAL CHARACTERISTICS Table of Graphs FIGURE Maximum peak output voltage vs Supply voltage 4 Maximum peak output voltage vs Free-air temperature 5 Maximum peak output voltage vs Load resistance 6 Maximum peak output voltage vs Frequency 7 Differential voltage amplification vs Free-air temperature 8 Large-signal dif
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 TYPICAL CHARACTERISTICS† MAXIMUM PEAK OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE MAXIMUM PEAK OUTPUT VOLTAGE vs SUPPLY VOLTAGE ±15 VOM VOM – Maximum Peak Output Voltage – V VOM – Maximum Peak Output Voltage – V VOM ±15 RL = 10 kΩ TA = 25°C See Figure 2 ±12.5 ±10 ±7.5 ÁÁ ÁÁ ±5 ±12.5 ±10 ±7.5 ÁÁ ÁÁ ±2.5 ±2.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 TYPICAL CHARACTERISTICS† AVD – Differential Voltage Amplification – V/mV DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE 10 VCC± = ±15 V RL = 10 kΩ 7 4 2 1 –75 –50 –25 0 25 50 75 TA – Free-Air Temperature – °C 100 125 Figure 8 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY VC
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 TYPICAL CHARACTERISTICS† SUPPLY CURRENT vs SUPPLY VOLTAGE SUPPLY CURRENT vs FREE-AIR TEMPERATURE ÁÁ ÁÁ ÁÁ 250 TA = 25°C No Signal No Load 200 I CC ICC ± – Supply Current – µA I CC ICC ± – Supply Current – µA 250 150 100 50 200 150 ÁÁ ÁÁ ÎÎÎÎÎ ÁÁ ÎÎÎÎÎ ÎÎÎÎÎ 100 50 0 0 2 4 6 8 10 12 14 16 0 –75 VCC± = ±
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 TYPICAL CHARACTERISTICS 1.03 1.3 1.2 Unity-Gain Bandwidth (left scale) 1.02 Phase Shift (right scale) 1.01 1.1 Slew Rate (left scale) 1 1 0.99 0.9 0.8 0.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 TYPICAL CHARACTERISTICS EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY OUTPUT VOLTAGE vs ELAPSED TIME Vn V n – Equivalent Input Noise Voltage – nV/ Hz 24 VO – Output Voltage – mV ÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁ 100 28 Overshoot 20 90% 16 12 8 4 10% VCC± = ±15 V RL = 10 kΩ TA = 25°C 0 tr –4 0 0.2 0.4 0.6 0.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 APPLICATION INFORMATION Table of Application Diagrams PART NUMBER FIGURE Instrumentation amplifier TL064 19 0.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 APPLICATION INFORMATION VCC+ – 1 MΩ TL064 VCC+ Output A + – 1 µF TL064 + TL064 Output B + 100 kΩ VCC+ VCC+ – 100 kΩ 100 µF VCC+ – Input 100 kΩ TL064 Output C + Figure 22. Audio-Distribution Amplifier 15 V 10 kΩ 10 kΩ 10 kΩ + TIL601 100 pF TL061 – 10 kΩ 10 kΩ 5 kΩ 10 kΩ –15 V Figure 23.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 APPLICATION INFORMATION VCC+ 0.1 µF 10 kΩ 10 kΩ 1 MΩ – Output TL061 50 Ω + N2 10 kΩ 0.1 µF N1 250 kΩ Figure 24. AC Amplifier 10 kΩ 0.1 µF 100 kΩ 0.06 µF 0.06 µF + TL061 – 1.2 MΩ 47 kΩ 1 kΩ 1 µF 10 kΩ 0.002 µF 100 kΩ 50 kΩ 2.7 kΩ 270 Ω 100 kΩ 0.003 µF 0.001 µF 10 kΩ 100 kΩ + 50 kΩ 20 µF 0.
TL061, TL061A, TL061B, TL061Y, TL062, TL062A TL062B, TL062Y, TL064, TL064A, TL064B, TL064Y LOW-POWER JFET-INPUT OPERATIONAL AMPLIFIERS SLOS078F – NOVEMBER 1978 – REVISED JANUARY 1999 APPLICATION INFORMATION IC PREAMPLIFIER RESPONSE CHARACTERISTICS 25 ÁÁÁÁ ÁÁÁÁ ÁÁÁÁ Max Bass 20 VCC± = ±15 V TA = 25°C 15 Voltage Amplification – dB Max Treble 10 5 0 –5 –10 ÁÁÁÁ ÁÁÁÁ –15 –20 –25 20 40 ÁÁÁ ÁÁÁ Min Treble Min Bass 100 200 400 1k 2k 4k 10 k 20 k f – Frequency – Hz 220 kΩ 0.00375 µF 0.
IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete.
