Datasheet
TL071, TL071A, TL071B
TL072, TL072A, TL072B, TL074, TL074A, TL074B
www.ti.com
SLOS080L –SEPTEMBER 1978–REVISED FEBRUARY 2014
6.4 Electrical Characteristics
V
CC±
= ±15 V (unless otherwise noted)
TL071M
TL074M
TL072M
PARAMETER TEST CONDITIONS
(1)
T
A
(2)
UNIT
MIN TYP MAX MIN TYP MAX
25°C 3 6 3 9
V
IO
Input offset voltage V
O
= 0, R
S
= 50 Ω mV
Full range 9 15
Temperature coefficient
α
VIO
V
O
= 0, R
S
= 50 Ω Full range 18 18 μV/°C
of input offset voltage
25°C 5 100 5 100 pA
I
IO
Input offset current V
O
= 0
Full range 20 20 nA
25°C 65 200 65 200 pA
I
IB
Input bias current V
O
= 0
50 20 nA
Common-mode input
V
ICR
25°C ±11 –12 to 15 ±11 –12 to 15 V
voltage range
R
L
= 10 kΩ 25°C ±12 ±13.5 ±12 ±13.5
Maximum peak output
V
OM
R
L
≥ 10 kΩ ±12 ±12 V
voltage swing
Full range
R
L
≥ 2 kΩ ±10 ±10
25°C 35 200 35 200
Large-signal differential
A
VD
V
O
= ±10 V, R
L
≥ 2 kΩ V/mV
voltage amplification
15 15
B
1
Unity-gain bandwidth 3 3 MHz
r
i
Input resistance Ω
10
12
10
12
Common-mode V
IC
= V
ICR
min,
CMRR 25°C 80 86 80 86 dB
rejection ratio V
O
= 0, R
S
= 50 Ω
Supply-voltage rejection V
CC
= ±9 V to ±15 V,
k
SVR
25°C 80 86 80 86 dB
ratio (ΔV
CC±
/ΔV
IO
) V
O
= 0, R
S
= 50 Ω
Supply current
I
CC
V
O
= 0, No load 25°C 1.4 2.5 1.4 2.5 mA
(each amplifier)
V
O1
/V
O2
Crosstalk attenuation A
VD
= 100 25°C 120 120 dB
(1) Input bias currents of an FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive, as
shown in Figure 4. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as
possible.
(2) All characteristics are measured under open-loop conditions with zero common-mode voltage, unless otherwise specified. Full range is
T
A
= –55°C to 125°C.
6.5 Operating Characteristics
V
CC±
= ±15 V, T
A
= 25°C
TL07xM ALL OTHERS
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
Slew rate at unity V
I
= 10 V, R
L
= 2 kΩ,
SR 5 13 8 13 V/μs
gain C
L
= 100 pF, See Figure 1
0.1 0.1 μs
Rise-time overshoot V
I
= 20 V, R
L
= 2 kΩ,
t
r
factor C
L
= 100 pF, See Figure 1
20 20 %
f = 1 kHz 18 18 nV/√Hz
Equivalent input noise
V
n
R
S
= 20 Ω
voltage
f = 10 Hz to 10 kHz 4 4 μV
Equivalent input noise
I
n
R
S
= 20 Ω, f = 1 kHz 0.01 0.01 pA/√Hz
current
V
I
rms = 6 V,
Total harmonic A
VD
= 1,
THD R
L
≥ 2 kΩ, 0.003 0.003 %
distortion RS ≤ 1 kΩ,
f = 1 kHz,
Copyright © 1978–2014, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: TL071 TL071A TL071B TL072 TL072A TL072B TL074 TL074A TL074B