Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsPMICsPMIC - LDO voltage regulator Positive, fixed SOIC 8

  

  



SLVS017R − SEPTEMBER 1987 − REVISED AUGUST 2003

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

D Very Low Dropout Voltage, Less Than 0.6 V

at 150 mA

D Very Low Quiescent Current

D TTL- and CMOS-Compatible Enable on

TL751L Series

D 60-V Load-Dump Protection

D Reverse Transient Protection Down To

−50 V

D Internal Thermal-Overload Protection

D Overvoltage Protection

D Internal Overcurrent-Limiting Circuitry

D Less Than 500-µA Disable (TL751L Series)

description/ordering information

The TL750L and TL751L series of fixed-output voltage regulators offer 5-V, 8-V, 10-V, and 12-V options. The

TL751L series also has an enable (ENABLE

) input. When ENABLE is high, the regulator output is placed in the

high-impedance state. This gives the designer complete control over power up, power down, or emergency

shutdown.

The TL750L and TL751L series are low-dropout positive-voltage regulators specifically designed for

battery-powered systems. These devices incorporate overvoltage and current-limiting protection circuitry,

along with internal reverse-battery protection circuitry to protect the devices and the regulated system. The

series is fully protected against 60-V load-dump and reverse-battery conditions. Extremely low quiescent

current during full-load conditions makes these devices ideal for standby power systems.

   ! "#$ !  %#&'" ($)

(#"! "  !%$""! %$ *$ $!  $+! !#$!

!(( ,-) (#" %"$!!. ($!  $"$!!'- "'#($

$!.  '' %$$!)



Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

OUTPUT

INPUT

COMMON

OUTPUT

COMMON

INPUT

COMMON

TL750L ...D PACKAGE

(TOP VIEW)

TL750L . . . KC PACKAGE

(TOP VIEW)

TL750L . . . LP PACKAGE

(TO-92, TO-226AA)

(TOP VIEW)

OUTPUT

COMMON

INPUT

COMMON

ENABLE

OUTPUT

INPUT

COMMON

ENABLE

TL750L ...P PACKAGE

(TOP VIEW)

TL751L ...D PACKAGE

(TOP VIEW)

TL751L ...P PACKAGE

(TOP VIEW)

INPUT

COMMON

OUTPUT

NC − No internal connection

TL750L . . . KTE PACKAGE

(TOP VIEW)

OUTPUT

COMMON

INPUT

COMMON

OUTPUT

INPUT

COMMON

NC − No internal connection

Summary of content (16 pages)

PAGE 1
SLVS017R − SEPTEMBER 1987 − REVISED AUGUST 2003 D Very Low Dropout Voltage, Less Than 0.6 V D OUTPUT COMMON COMMON NC 1 8 2 7 3 6 4 5 TL750L . . . KC PACKAGE (TOP VIEW) COMMON TL750L . . . D PACKAGE (TOP VIEW) D D D D −50 V Internal Thermal-Overload Protection Overvoltage Protection Internal Overcurrent-Limiting Circuitry Less Than 500-µA Disable (TL751L Series) INPUT COMMON COMMON NC OUTPUT COMMON INPUT TL750L . . .
PAGE 2
SLVS017R − SEPTEMBER 1987 − REVISED AUGUST 2003 description/ordering information (continued) ORDERING INFORMATION TJ VO TYP AT 25°C POWER-FLEX (KTE) TL750L05CKTER Tube of 75 TL750L05CD Reel of 2500 TL750L05CDR Tube of 75 TL751L05CD Reel of 2500 TL751L05CDR Bulk of 1000 TL750L05CLP Reel of 2000 TL750L05CLPR Tube of 50 TL750L05CKC Tube of 75 TL750L08CD Reel of 2500 TL750L08CDR TO-226 / TO-92 (LP) Bulk of 1000 TL750L08CLP 750L08C PDIP
PAGE 3
SLVS017R − SEPTEMBER 1987 − REVISED AUGUST 2003 absolute maximum ratings over operating junction temperature range (unless otherwise noted)† Continuous input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 V Transient input voltage, TA = 25°C (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
SLVS017R − SEPTEMBER 1987 − REVISED AUGUST 2003 electrical characteristics, VI = 14 V, IO = 10 mA, TJ = 25°C (unless otherwise noted) Output voltage VI = 6 V to 26 V, Input regulation voltage VI = 9 V to 16 V VI = 6 V to 26 V Ripple rejection Output regulation voltage TL750L05 TL751L05 TEST CONDITIONS† PARAMETER VI = 8 V to 18 V, IO = 5 mA to 150 mA Dropout voltage IO = 10 mA IO = 150 mA Output noise voltage f = 10 Hz to 100 kHz Input bias cur
PAGE 5
SLVS017R − SEPTEMBER 1987 − REVISED AUGUST 2003 electrical characteristics, VI = 14 V, IO = 10 mA, TJ = 25°C (unless otherwise noted) Output voltage VI = 11 V to 26 V, Input regulation voltage VI = 12 V to 19 V VI = 11 V to 26 V Ripple rejection Output regulation voltage TL750L10 TL751L10 TEST CONDITIONS† PARAMETER VI = 12 V to 22 V, IO = 5 mA to 150 mA Dropout voltage IO = 10 mA IO = 150 mA Output noise voltage f = 10 Hz to 100 kHz Input bia
PAGE 6
SLVS017R − SEPTEMBER 1987 − REVISED AUGUST 2003 TYPICAL CHARACTERISTICS TL750L05 INPUT CURRENT vs INPUT VOLTAGE TRANSIENT INPUT VOLTAGE vs TIME 40 TA = 25°C VI = 14 V + 46e(−t/0.
PAGE 7
SLVS017R − SEPTEMBER 1987 − REVISED AUGUST 2003 TYPICAL CHARACTERISTICS TL750L05 EQUIVALENT SERIES RESISTANCE vs LOAD CURRENT ESR − Equivalent Series Resistance − Ω 1.0 CL = 10-µF Tantalum Capacitor TA = − 40°C to 125°C 0.9 0.8 Potential Instability Region 0.7 0.6 0.5 0.4 0.3 Region of Best Stability 0.2 0.1 0.
PAGE 8
MECHANICAL DATA MCER001A – JANUARY 1995 – REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0°–15° 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters).
PAGE 9
MECHANICAL DATA MLCC006B – OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.
PAGE 10
MECHANICAL DATA MPDI001A – JANUARY 1995 – REVISED JUNE 1999 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE 0.400 (10,60) 0.355 (9,02) 8 5 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.020 (0,51) MIN 0.015 (0,38) Gage Plane 0.200 (5,08) MAX Seating Plane 0.010 (0,25) NOM 0.125 (3,18) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.430 (10,92) MAX 0.010 (0,25) M 4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B.
PAGE 11
MECHANICAL DATA MPFM001E – OCTOBER 1994 – REVISED JANUARY 2001 KTE (R-PSFM-G3) PowerFLEX PLASTIC FLANGE-MOUNT 0.375 (9,52) 0.080 (2,03) 0.070 (1,78) 0.365 (9,27) 0.360 (9,14) 0.050 (1,27) 0.040 (1,02) 0.350 (8,89) 0.220 (5,59) NOM 0.010 (0,25) NOM Thermal Tab (See Note C) 0.360 (9,14) 0.350 (8,89) 0.295 (7,49) NOM 0.320 (8,13) 0.310 (7,87) 0.420 (10,67) 0.410 (10,41) 1 3 0.025 (0,63) 0.031 (0,79) 0.100 (2,54) Seating Plane 0.004 (0,10) 0.010 (0,25) M 0.005 (0,13) 0.001 (0,03) 0.
PAGE 12
PAGE 13
MECHANICAL DATA MSOT002A – OCTOBER 1994 – REVISED NOVEMBER 2001 LP (O-PBCY-W3) PLASTIC CYLINDRICAL PACKAGE 0.205 (5,21) 0.175 (4,44) 0.165 (4,19) 0.125 (3,17) DIA 0.210 (5,34) 0.170 (4,32) Seating Plane 0.157 (4,00) MAX 0.050 (1,27) C 0.500 (12,70) MIN 0.104 (2,65) FORMED LEAD OPTION 0.022 (0,56) 0.016 (0,41) 0.016 (0,41) 0.014 (0,35) STRAIGHT LEAD OPTION D 0.135 (3,43) MIN 0.105 (2,67) 0.095 (2,41) 0.055 (1,40) 0.045 (1,14) 1 2 3 0.105 (2,67) 0.080 (2,03) 0.105 (2,67) 0.
PAGE 14
MECHANICAL DATA MSOT002A – OCTOBER 1994 – REVISED NOVEMBER 2001 LP (O-PBCY-W3) PLASTIC CYLINDRICAL PACKAGE 0.539 (13,70) 0.460 (11,70) 1.260 (32,00) 0.905 (23,00) 0.650 (16,50) 0.610 (15,50) 0.020 (0,50) MIN 0.098 (2,50) 0.384 (9,75) 0.335 (8,50) 0.748 (19,00) 0.217 (5,50) 0.433 (11,00) 0.335 (8,50) 0.748 (19,00) 0.689 (17,50) 0.114 (2,90) 0.094 (2,40) 0.114 (2,90) 0.094 (2,40) 0.169 (4,30) 0.146 (3,70) DIA 0.266 (6,75) 0.234 (5,95) 0.512 (13,00) 0.
PAGE 15
PAGE 16
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.