Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Op-amp Multi-purpose PDIP 14

 

  

 



SLOS190G − FEBRUARY 1997 − REVISED MAY 2004

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

D Output Swing Includes Both Supply Rails

D Low Noise ...9 nV/√Hz Typ at f = 1 kHz

D Low Input Bias Current ...1 pA Typ

D Fully Specified for Both Single-Supply and

Split-Supply Operation

D Common-Mode Input Voltage Range

Includes Negative Rail

D High-Gain Bandwidth . . . 2.2 MHz Typ

D High Slew Rate . . . 3.6 V/µs Typ

D Low Input Offset Voltage

950 µV Max at T

= 25°C

D Macromodel Included

D Performance Upgrades for the TS272,

TS274, TLC272, and TLC274

D Available in Q-Temp Automotive

HighRel Automotive Applications

Configuration Control / Print Support

Qualification to Automotive Standards

description

The TLC2272 and TLC2274 are dual and

quadruple operational amplifiers from Texas

Instruments. Both devices exhibit rail-to-rail

output performance for increased dynamic range

in single- or split-supply applications. The

TLC227x family offers 2 MHz of bandwidth and

3 V/µs of slew rate for higher speed applications.

These devices offer comparable ac performance

while having better noise, input offset voltage, and

power dissipation than existing CMOS

operational amplifiers. The TLC227x has a noise

voltage of 9 nV/√Hz

, two times lower than

competitive solutions.

The TLC227x, exhibiting high input impedance

and low noise, is excellent for small-signal

conditioning for high-impedance sources, such as

piezoelectric transducers. Because of the micro-

power dissipation levels, these devices work well

in hand-held monitoring and remote-sensing

applications. In addition, the rail-to-rail output

feature, with single- or split-supplies, makes this

family a great choice when interfacing with analog-to-digital converters (ADCs). For precision applications, the

TLC227xA family is available with a maximum input offset voltage of 950 µV. This family is fully characterized

at 5 V and ±5 V.

The TLC2272/4 also makes great upgrades to the TLC272/4 or TS272/4 in standard designs. They offer

increased output dynamic range, lower noise voltage, and lower input offset voltage. This enhanced feature set

allows them to be used in a wider range of applications. For applications that require higher output drive and

wider input voltage range, see the TLV2432 and TLV2442 devices.

If the design requires single amplifiers, see the TLV2211/21/31 family. These devices are single rail-to-rail

operational amplifiers in the SOT-23 package. Their small size and low power consumption, make them ideal

for high density, battery-powered equipment.

  !" # $" #  %$&'" "(

$"# ! " #%"# % ") "!#  # #"$!"#

#" *"+( $" %##, # " ##'+ '$

"#",  '' %!"#(



Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

Advanced LinCMOS is a trademark of Texas Instruments.

DD±

| − Supply Voltage − V

46 8

10 12 14

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE

SUPPLY VOLTAGE

= 25°C

= ±50 µA

= ±500 µA

V(OPP) − Maximum Peak-to-Peak Output Voltage − VV

O(PP)

 %$"# !%'" " -./-/ '' %!"#  "#"

$'## ")*# "(  '' ") %$"# %$"

%##, # " ##'+ '$ "#",  '' %!"#(

Summary of content (77 pages)

PAGE 1
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 D D D D D D D Output Swing Includes Both Supply Rails Low Noise . . . 9 nV/√Hz Typ at f = 1 kHz Low Input Bias Current . . . 1 pA Typ Fully Specified for Both Single-Supply and Split-Supply Operation Common-Mode Input Voltage Range Includes Negative Rail High-Gain Bandwidth . . . 2.2 MHz Typ High Slew Rate . . . 3.
PAGE 2
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272 AVAILABLE OPTIONS PACKAGED DEVICES TA VIOmax At 25°C SMALL OUTLINE† (D) CERAMIC LCC (FK) CERAMIC DIP (JG) PLASTIC DIP (P) TSSOP‡ (PW) CERAMIC FLAT PACK (U) 950 µV 2.5 mV TLC2272ACD TLC2272CD — — — — TLC2272ACP TLC2272CP TLC2272ACPW 0°C to 70°C — — 950 µV 2.5 mV TLC2272AID TLC2272ID — — — — TLC2272AIP TLC2272IP 950 µV 2.
PAGE 3
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 1 8 2 7 3 6 4 5 VDD + 2OUT 2IN − 2IN + NC 1OUT NC VDD+ NC TLC2272 FK PACKAGE (TOP VIEW) 1OUT 1IN − 1IN + VDD + 2IN + 2IN − 2OUT 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC VDD−/GND NC 2 IN+ NC NC 1 IN− NC 1 IN+ NC NC 2 OUT NC 2 IN− NC 1 14 2 13 3 12 4 11 5 10 6 9 7 8 4OUT 4IN − 4IN + VDD − 3IN + 3IN − 3OUT TLC2272 U PACKAGE (TOP VIEW) NC 1 OU
PAGE 4
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 equivalent schematic (each amplifier) VDD + Q3 Q6 Q9 Q12 Q14 Q16 IN + OUT C1 IN − R5 Q1 Q4 Q13 Q15 Q17 D1 Q2 Q5 R3 R4 Q7 Q8 Q10 Q11 R1 VDD− ACTUAL DEVICE COMPONENT COUNT† TLC2272 TLC2274 Transistors COMPONENT 38 76 Resistors 26 52 9 18 Diodes Capacitors 3 6 † Includes both amplifiers and all ESD, bias, and trim circuitry 4 POST OFFICE BOX 655303 • DALLAS, TE
PAGE 5
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V Supply voltage, VDD − (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 6
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272C electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage TEST CONDITIONS High-level output voltage 25°C VIC = 0 V, VD
PAGE 7
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272C operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER SR Slew rate at unity gain TEST CONDITIONS VO = 0.5 V to 2.5 V, RL = 10 kkΩ‡, CL = 100 pF‡ 2.3 3.6 Full range 1.7 MIN TYP 2.3 3.6 25°C 9 9 f = 0.1 Hz to 1 Hz 25°C 1 1 f = 0.1 Hz to 10 Hz 25°C 1.4 1.4 25°C 0.6 0.
PAGE 8
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272C electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise specified) PARAMETER VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current TA† TEST CONDITIONS 25°C Common-mode input voltage VO = 0 V, VIC = 0 V, VIC = 0 V, VI
PAGE 9
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272C operating characteristics at specified free-air temperature, VDD ± = ±5 V PARAMETER TEST CONDITIONS TLC2272C TA† MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2272AC MAX MIN TYP 2.3 3.6 Slew rate at unity gain VO = ± 2.3 V, CL = 100 pF Equivalent input noise voltage f = 10 Hz 25°C 50 50 Vn f = 1 kHz 25°C 9 9 Peak-to-peak equivalent input noise voltage f = 0.
PAGE 10
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274C electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage TEST CONDITIONS High-level output voltage 25°C VDD ± = ± 2.
PAGE 11
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274C operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS TA† TLC2274C MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2274AC MAX MIN TYP 2.3 3.6 Slew rate at unity gain VO = 0.5 V to 2.5 V, RL = 10 kΩ‡, Equivalent input noise voltage f = 10 Hz 25°C 50 50 Vn f = 1 kHz 25°C 9 9 Peak-to-peak equivalent input noise voltage f = 0.
PAGE 12
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274C electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise noted) PARAMETER VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage TEST CONDITIONS 2500 VO = 0 V, VO = ± 4 V RL = 1 MΩ µV
PAGE 13
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274C operating characteristics at specified free-air temperature, VDD ± = ±5 V PARAMETER TEST CONDITIONS TLC2274C TA† MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2274AC MAX MIN TYP 2.3 3.6 Slew rate at unity gain VO = ± 2.3 V, CL = 100 pF Equivalent input noise voltage f = 10 Hz 25°C 50 50 Vn f = 1 Hz 25°C 9 9 Peak-to-peak equivalent input noise voltage f = 0.
PAGE 14
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO TLC2272I TEST CONDITIONS TA† MIN 25°C 25°C 25 C to 85°C VDD ± = ± 2.
PAGE 15
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272I operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS TLC2272I TA† MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2272AI MAX MIN TYP 2.3 3.6 MAX UNIT Slew rate at unity gain VO = 0.5 V to 2.
PAGE 16
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272I electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO TLC2272I TEST CONDITIONS TA† MIN 25°C VICR VO = 0 V, Input bias current RS = 50 Ω Ω, Maximum positive peak output voltage VIC = 0
PAGE 17
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272I operating characteristics at specified free-air temperature, VDD ± = ±5 V PARAMETER TEST CONDITIONS TLC2272I TA† MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2272AI MAX MIN TYP 2.3 3.6 Slew rate at unity gain VO = ± 2.3 V, CL = 100 pF Equivalent input noise voltage f = 10 Hz 25°C 50 50 Vn f = 1 kHz 25°C 9 9 Peak-to-peak equivalent input noise voltage f = 0.
PAGE 18
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO TEST CONDITIONS TA† TLC2274I MIN 25°C VICR VIC = 0 V, RS = 50 Ω Input bias current RS = 50 Ω Ω, High-level output voltage IOH = − 1 m
PAGE 19
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274I operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS TLC2274I TA† MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2274AI MAX MIN TYP 2.3 3.6 Slew rate at unity gain VO = 0.5 V to 2.
PAGE 20
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274I electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO TA† TEST CONDITIONS TLC2274I MIN 25°C VICR VO = 0 V, Input bias current RS = 50 Ω Ω, Maximum positive peak output voltage VOM − M
PAGE 21
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274I operating characteristics at specified free-air temperature, VDD ± = ±5 V PARAMETER TEST CONDITIONS TLC2274I TA† MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2274AI MAX MIN TYP 2.3 3.6 Slew rate at unity gain VO = ± 2.3 V, CL = 100 pF Equivalent input noise voltage f = 10 Hz 25°C 50 50 Vn f = 1 kHz 25°C 9 9 Peak-to-peak equivalent input noise voltage f = 0.
PAGE 22
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272Q and TLC2272M electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TLC2272Q, TLC2272M TA† TEST CONDITIONS MIN VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage longterm drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage 25°C
PAGE 23
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272Q and TLC2272M operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS TLC2272Q, TLC2272M TA† MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2272AQ, TLC2272AM MAX MIN TYP 2.3 3.6 Slew rate at unity gain VO = 1.25 V to 2.
PAGE 24
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272Q and TLC2272M electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLC2272Q, TLC2272M MIN VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage
PAGE 25
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2272Q and TLC2272M operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER TEST CONDITIONS TLC2272Q, TLC2272M TA† MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2272AQ, TLC2272AM MAX MIN TYP 2.3 3.
PAGE 26
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274Q and TLC2274M electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLC2274Q, TLC2274M MIN VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage 25°
PAGE 27
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274Q and TLC2274M operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS CL = 100 pF‡ TLC2274Q, TLC2274M TA† MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2274AQ, TLC2274AM MAX MIN TYP 2.3 3.6 Slew rate at unity gain VO = 0.5 V to 2.
PAGE 28
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274Q and TLC2274M electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER TA† TEST CONDITIONS TLC2274Q, TLC2274M MIN 25°C VIO Input offset voltage αVIO Temperature coefficient of input offset voltage Input offset voltage longterm drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input volta
PAGE 29
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TLC2274Q and TLC2274M operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER TEST CONDITIONS TLC2274Q, TLC2274M TA† MIN TYP 25°C 2.3 3.6 Full range 1.7 TLC2274AQ, TLC2274AM MAX MIN TYP 2.3 3.6 Slew rate at unity gain VO = ± 2.
PAGE 30
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO Input offset voltage Distribution vs Common-mode voltage αVIO IIB /IIO Input offset voltage temperature coefficient Distribution Input bias and input offset current vs Free-air temperature 11 VI Input voltage vs Supply voltage vs Free-air temperature 12 13 VOH VOL High-level output voltage vs High-level output current 14 Low-l
PAGE 31
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLC2272 INPUT OFFSET VOLTAGE DISTRIBUTION OF TLC2272 INPUT OFFSET VOLTAGE 15 20 891 Amplifiers From 2 Wafer Lots VDD = ± 2.5 V TA = 25°C Percentage of Amplifiers − % Percentage of Amplifiers − % 20 10 5 0 −1.6 −1.2 −0.8 −0.4 0 0.4 0.8 1.2 15 891 Amplifiers From 2 Wafer Lots VDD = ± 5 V TA = 25°C 10 5 0 −1.6 −1.2 −0.8 −0.4 1.6 0.4 0.
PAGE 32
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS INPUT OFFSET VOLTAGE vs COMMON-MODE VOLTAGE INPUT OFFSET VOLTAGE vs COMMON-MODE VOLTAGE 1 VDD = 5 V TA = 25°C RS = 50 Ω VIO − Input Offset Voltage − mV VIO VIO VIO − Input Offset Voltage − mV 1 0.5 0 −0.5 −1 −1 0 2 1 3 0.5 0 −0.
PAGE 33
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS 25 25 128 Amplifiers From 2 Wafer Lots VDD = ± 2.5 V N Package TA = 25°C to 125°C 20 Percentage of Amplifiers − % Percentage of Amplifiers − % DISTRIBUTION OF TLC2274 vs INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT† DISTRIBUTION OF TLC2274 vs INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT† 15 10 5 0 −5 128 Amplifiers From 2 Wafer Lots VDD = ± 2.
PAGE 34
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS INPUT VOLTAGE† vs FREE-AIR TEMPERATURE HIGH-LEVEL OUTPUT VOLTAGE† vs HIGH-LEVEL OUTPUT CURRENT 5 6 VDD = 5 V V0H V OH − High-Level Output Voltage − V VDD = 5 V V I − Input Voltage − V 4 3 |VIO| ≤ 5 mV 2 1 0 −1 −75 − 50 5 4 TA = 125°C 3 TA = 25°C 2 TA = − 55°C 1 0 − 25 0 25 50 75 100 125 0 TA − Free-Air Temperature − °C 1 Figure 13 1.
PAGE 35
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS 5 VDD ± = ± 5 V 4 TA = − 55°C TA = 25°C 3 TA = 125°C 2 1 0 1 2 3 4 5 MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE† vs OUTPUT CURRENT V OM − − Maximum Negative Peak Output Voltage − V V OM + − Maximum Positive Peak Output Voltage − V MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE† vs OUTPUT CURRENT −3.8 VDD = ± 5 V VIC = 0 V −4 TA = 125°C −4.2 TA = 25°C −4.
PAGE 36
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS SHORT-CIRCUIT OUTPUT CURRENT† vs FREE-AIR TEMPERATURE IIOS OS − Short-Circuit Output Current − mA 15 OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE 5 VO = 0 V VDD = ± 5 V VID = − 100 mV 11 VO − Output Voltage − V 4 7 −3 VDD = 5 V TA = 25°C RL = 10 kΩ VIC = 2.
PAGE 37
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE MARGIN vs FREQUENCY 80 135° 40 90° 20 45° 0 0° −20 φom m − Phase Margin AVD AVD− Large-Signal Differential Voltage Amplification − dB 60 ÁÁ ÁÁ ÁÁ 180° VDD = 5 V RL = 10 kΩ CL = 100 pF TA = 25°C −45° −40 1k 10 k 100 k 1M −90° 10 M f − Frequency − Hz Figure 25 LARGE-SIGNAL DIFFERENTIAL VOLTAG
PAGE 38
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION† vs FREE-AIR TEMPERATURE LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION† vs FREE-AIR TEMPERATURE 1k VDD = ± 5 V VIC = 0 V VO = ± 4 V VDD = 5 V VIC = 2.
PAGE 39
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS COMMON-MODE REJECTION RATIO vs FREQUENCY 90 TA = 25°C CMRR − Common-Mode Rejection Ratio − dB CMRR − Common-Mode Rejection Ratio − dB 100 COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE VDD = ± 5 V 80 VDD = 5 V 60 40 20 86 82 VIC = − 5 V to 2.7 V 78 VDD = 5 V 74 0 10 100 1k 10 k 100 k 1M VDD = ± 5 V 70 −75 10 M VIC = 0 V to 2.
PAGE 40
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS TLC2272 SUPPLY CURRENT† vs SUPPLY VOLTAGE SUPPLY VOLTAGE REJECTION RATIO† vs FREE-AIR TEMPERATURE 3 VDD ± = ± 2.2 V to ± 8 V VO = 0 V VO = 0 V No Load 2.4 105 IIDD DD − Supply Current − mA kSVR k SVR − Supply Voltage Rejection Ratio − dB 110 100 95 TA = 25°C TA = − 55°C 1.2 TA = 125°C 0.6 90 85 −75 1.
PAGE 41
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS TLC2274 SUPPLY CURRENT† vs FREE-AIR TEMPERATURE SLEW RATE vs LOAD CAPACITANCE 5 6 VDD = ± 5 V VO = 0 V 4 SR − Slew Rate − V/ µ s IIDD DD − Supply Current − mA 4.8 VDD = 5 V VO = 2.5 V 3.6 2.4 SR − 3 2 SR + 1 1.
PAGE 42
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE INVERTING LARGE-SIGNAL PULSE RESPONSE 5 3 2 4 VO − Output Voltage − V VO 4 V VO O − Output Voltage − V 5 VDD = ± 5 V RL = 10 kΩ CL = 100 pF TA = 25°C AV = − 1 1 0 −1 −2 VDD = 5 V RL = 10 kΩ CL = 100 pF AV = 1 TA = 25°C 3 2 −3 1 −4 −5 0 1 2 3 4 5 6 7 8 0 9 0 1 2 3 t − Time − µs Figure 43 5 6 7
PAGE 43
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE INVERTING SMALL-SIGNAL PULSE RESPONSE 2.65 VDD = ± 5 V RL = 10 kΩ CL = 100 pF TA = 25°C AV = 1 50 VDD = 5 V RL = 10 kΩ CL = 100 pF TA = 25°C AV = 1 2.6 VO − Output Voltage − V VO VO − Output Voltage − mV VO 100 0 −50 2.55 2.5 2.45 −100 2.4 0 0.5 1 1.5 2 2.5 3 3.
PAGE 44
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS NOISE VOLTAGE OVER A 10 SECOND PERIOD 60 1000 VDD = ± 5 V TA = 25°C RS = 20 Ω 50 VDD = 5 V f = 0.
PAGE 45
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 TYPICAL CHARACTERISTICS GAIN-BANDWIDTH PRODUCT† vs FREE-AIR TEMPERATURE GAIN-BANDWIDTH PRODUCT vs SUPPLY VOLTAGE 3 f = 10 kHz RL = 10 kΩ CL = 100 pF TA = 25°C 2.4 VDD = 5 V f = 10 kHz RL = 10 kΩ CL = 100 pF 2.8 Gain-Bandwidth Product − MHz Gain-Bandwidth Product − MHz 2.5 2.3 2.2 2.1 2.6 2.4 2.2 2 1.8 1.6 1.
PAGE 46
 SLOS190G − FEBRUARY 1997 − REVISED MAY 2004 APPLICATION INFORMATION macromodel information Macromodel information provided was derived using Microsim Parts, the model generation software used with Microsim PSpice. The Boyle macromodel (see Note 5) and subcircuit in Figure 59 were generated using the TLC227x typical electrical and operating characteristics at TA = 25°C.
PAGE 47
PACKAGE OPTION ADDENDUM www.ti.
PAGE 48
PACKAGE OPTION ADDENDUM www.ti.
PAGE 49
PACKAGE OPTION ADDENDUM www.ti.
PAGE 50
PACKAGE OPTION ADDENDUM www.ti.
PAGE 51
PACKAGE OPTION ADDENDUM www.ti.
PAGE 52
PACKAGE OPTION ADDENDUM www.ti.
PAGE 53
PACKAGE OPTION ADDENDUM www.ti.
PAGE 54
PACKAGE OPTION ADDENDUM www.ti.
PAGE 55
PACKAGE OPTION ADDENDUM www.ti.
PAGE 56
PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
PAGE 57
PACKAGE OPTION ADDENDUM www.ti.
PAGE 58
PACKAGE MATERIALS INFORMATION www.ti.com 8-Jul-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device 5962-9555201NXDR Package Package Pins Type Drawing SOIC SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLC2272ACDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLC2272ACPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.
PAGE 59
PACKAGE MATERIALS INFORMATION www.ti.com 8-Jul-2013 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TLC2274CPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TLC2274IDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 TLC2274IPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TLC2274MDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.
PAGE 60
PACKAGE MATERIALS INFORMATION www.ti.com 8-Jul-2013 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TLC2274ACDR SOIC D 14 2500 333.2 345.9 28.6 TLC2274ACPWR TSSOP PW 14 2000 367.0 367.0 35.0 TLC2274AIDR SOIC D 14 2500 333.2 345.9 28.6 TLC2274AIPWR TSSOP PW 14 2000 367.0 367.0 35.0 TLC2274AQDR SOIC D 14 2500 367.0 367.0 38.0 TLC2274CDR SOIC D 14 2500 333.2 345.9 28.6 TLC2274CNSR SO NS 14 2000 367.0 367.0 38.
PAGE 61
MECHANICAL DATA MCER001A – JANUARY 1995 – REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0°–15° 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters).
PAGE 62
PAGE 63
PAGE 64
PAGE 65
PAGE 66
PAGE 67
PAGE 68
PAGE 69
PAGE 70
PAGE 71
PAGE 72
PAGE 73
PAGE 74
PAGE 75
PAGE 76
PAGE 77
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.