Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Op-amp Multi-purpose SOIC 8

TLC272, TLC272A, TLC272B, TLC272Y, TLC277

LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS

SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

D Trimmed Offset Voltage:

TLC277 . . . 500 µV Max at 25°C,

= 5 V

D Input Offset Voltage Drift ...Typically

0.1 µV/Month, Including the First 30 Days

D Wide Range of Supply Voltages Over

Specified Temperature Range:

0°C to 70°C...3 V to 16 V

–40°C to 85°C...4 V to 16 V

–55°C to 125°C...4 V to 16 V

D Single-Supply Operation

D Common-Mode Input Voltage Range

Extends Below the Negative Rail (C-Suffix,

I-Suffix types)

D Low Noise ...Typically 25 nV/√Hz at

f = 1 kHz

D Output Voltage Range Includes Negative

Rail

D High Input impedance ...10

Ω Typ

D ESD-Protection Circuitry

D Small-Outline Package Option Also

Available in Tape and Reel

D Designed-In Latch-Up Immunity

description

The TLC272 and TLC277 precision dual

operational amplifiers combine a wide range of

input offset voltage grades with low offset voltage

drift, high input impedance, low noise, and speeds

approaching those of general-purpose BiFET

devices.

These devices use Texas Instruments silicon-

gate LinCMOS technology, which provides

offset voltage stability far exceeding the stability

available with conventional metal-gate pro-

cesses.

The extremely high input impedance, low bias

currents, and high slew rates make these cost-

effective devices ideal for applications previously

reserved for BiFET and NFET products. Four

offset voltage grades are available (C-suffix and

I-suffix types), ranging from the low-cost TLC272

(10 mV) to the high-precision TLC277 (500 µV).

These advantages, in combination with good

common-mode rejection and supply voltage

rejection, make these devices a good choice for

new state-of-the-art designs as well as for

upgrading existing designs.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of Texas Instruments

standard warranty. Production processing does not necessarily include

testing of all parameters.

1OUT

1IN–

1IN+

GND

2OUT

2IN–

2IN+

D, JG, P, OR PW PACKAGE

3 2 1 20 19

910111213

2OUT

2IN–

1IN–

1IN+

FK PACKAGE

(TOP VIEW)

1OUT

2IN +

GND

NC – No internal connection

P Package

= 25°C

4000–400

800

– Input Offset Voltage – µV

Percentage of Units – %

–800

DISTRIBUTION OF TLC277

INPUT OFFSET VOLTAGE

473 Units Tested From 2 Wafer Lots

= 5 V

(TOP VIEW)

LinCMOS is a trademark of Texas Instruments.

Summary of content (51 pages)

PAGE 1
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 D Trimmed Offset Voltage: D D D D D D D D 1OUT 1IN – 1IN + GND 1 8 2 7 3 6 4 5 VDD 2OUT 2IN – 2IN + FK PACKAGE (TOP VIEW) NC 1OUT NC VDD NC D TLC277 . . . 500 µV Max at 25°C, VDD = 5 V Input Offset Voltage Drift . . . Typically 0.1 µV/Month, Including the First 30 Days Wide Range of Supply Voltages Over Specified Temperature Range: 0°C to 70°C . . .
PAGE 2
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 description (continued) AVAILABLE OPTIONS PACKAGED DEVICES TA VIOmax AT 25°C SMALL OUTLINE (D) CHIP CARRIER (FK) CERAMIC DIP (JG) PLASTIC DIP (P) TSSOP (PW) CHIP FORM (Y) 0°C to 70°c 500 µV 2 mV 5 mV 10mV TLC277CD TLC272BCD TLC272ACD TLC272CD — — — — — — — — TLC277CP TLC272BCP TLC272ACP TLC272CP — — — TLC272CPW — — — TLC272Y – 40°C to 85°C 500 µV 2 mV 5 m
PAGE 3
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 equivalent schematic (each amplifier) VDD P3 P4 R6 R1 N5 R2 IN – P5 P1 P6 P2 IN + R5 C1 OUT N3 N1 R3 N2 D1 N4 R4 D2 N6 N7 R7 GND TLC272Y chip information This chip, when properly assembled, displays characteristics similar to the TLC272C. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads.
PAGE 4
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLC272C, TLC272AC, TLC272BC, TLC277C MIN VIO TLC272C VO = 1.4 V, RS = 50 Ω, VIC = 0, RL = 10 kΩ TLC272AC VO = 1.
PAGE 6
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 electrical characteristics at specified free-air temperature, VDD = 10 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLC272C, TLC272AC, TLC272BC, TLC277C MIN VIO TLC272C VO = 1.4 V, RS = 50 Ω, VIC = 0, RL = 10 kΩ TLC272AC VO = 1.
PAGE 7
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLC272I, TLC272AI, TLC272BI, TLC277I MIN VIO TLC272I VO = 1.4 V, RS = 50 Ω, VIC = 0, RL = 10 kΩ TLC272AI VO = 1.
PAGE 8
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 electrical characteristics at specified free-air temperature, VDD = 10 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† TLC272I, TLC272AI, TLC272BI, TLC277I MIN VIO TLC272I VO = 1.4 V, RS = 50 Ω, VIC = 0, RL = 10 kΩ TLC272AI VO = 1.
PAGE 9
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO TEST CONDITIONS VO = 1.4 V, RS = 50 Ω, VIC = 0, RL = 10 kΩ Full range TLC277M VO = 1.4 V, RS = 50 Ω, VIC = 0, RL = 10 kΩ Full range Input offset voltage Temperature coefficient of input offset voltage IIO Input offset current (see Note 4) VO = 2.
PAGE 10
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 electrical characteristics at specified free-air temperature, VDD = 10 V (unless otherwise noted) PARAMETER VIO TEST CONDITIONS TLC272M VO = 1.4 V, RS = 50 Ω, VIC = 0, RL = 10 kΩ Full range TLC277M VO = 1.
PAGE 11
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 electrical characteristics, VDD = 5 V, TA = 25°C (unless otherwise noted) PARAMETER VIO Input offset voltage αVIO TEST CONDITIONS VO = 1.4 V, RS = 50 Ω, TLC272Y MIN VIC = 0, RL = 10 kΩ TYP MAX 11 1.1 10 UNIT mV Temperature coefficient of input offset voltage 1.8 µV/°C IIO IIB Input offset current (see Note 4) 0.1 pA 0.
PAGE 12
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS TA TLC272C, TLC272AC, TLC272BC, TLC277C MIN VIPP = 1 V SR Slew rate at unity gain RL = 10 kΩ, pF, CL = 20 pF See Figure 1 VIPP = 2.
PAGE 13
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS TA TLC272I, TLC272AI, TLC272BI, TLC277I MIN VIPP = 1 V SR Slew rate at unity gain RL = 10 kΩ, pF, CL = 20 pF See Figure 1 VIPP = 2.
PAGE 14
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS VIPP = 1 V SR Slew rate at unity gain RL = 10 kΩ, pF, CL = 20 pF See Figure 1 VIPP = 2.
PAGE 15
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 operating characteristics, VDD = 5 V, TA = 25°C PARAMETER TEST CONDITIONS MAX UNIT 3.6 RS = 20 Ω, See Figure 2 25 nV/√Hz VO = VOH, See Figure 1 CL = 20 pF, RL = 10 kΩ, 320 kHz VI = 10 mV, VI = 10 mV, See Figure 3 CL = 20 pF, See Figure 3 1.
PAGE 16
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 PARAMETER MEASUREMENT INFORMATION single-supply versus split-supply test circuits Because the TLC272 and TLC277 are optimized for single-supply operation, circuit configurations used for the various tests often present some inconvenience since the input signal, in many cases, must be offset from ground.
PAGE 17
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 PARAMETER MEASUREMENT INFORMATION input bias current Because of the high input impedance of the TLC272 and TLC277 operational amplifiers, attempts to measure the input bias current can result in erroneous readings. The bias current at normal room ambient temperature is typically less than 1 pA, a value that is easily exceeded by leakages on the test socket.
PAGE 18
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 PARAMETER MEASUREMENT INFORMATION full-power response Full-power response, the frequency above which the operational amplifier slew rate limits the output voltage swing, is often specified two ways: full-linear response and full-peak response.
PAGE 19
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO αVIO Input offset voltage Distribution 6, 7 Temperature coefficient of input offset voltage Distribution 8, 9 VOH High-level High level out output ut voltage vs High-level out output ut current vs Su Supply ly voltage vs Free-air temperature 10, 11 12 13 VOL Low level output voltage Low-level input vs Common-
PAGE 20
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLC272 INPUT OFFSET VOLTAGE DISTRIBUTION OF TLC272 INPUT OFFSET VOLTAGE Percentage of Units – % 50 40 ÌÌÌÌ ÌÌÌÌÌÌÌÌÌÌÌÌ ÌÌÌÌÌÌÌÌÌÌÌÌ ÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ 60 753 Amplifiers Tested From 6 Wafer Lots VDD = 5 V TA = 25°C P Package 50 Percentage of Units – % 60 30 20 40 ÌÌÌÌÌÌÌÌÌÌÌ ÌÌÌÌÌÌÌÌÌÌÌ ÌÌÌÌ ÌÌÌÌ ÌÌÌÌ 753 Amplifiers
PAGE 21
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS† HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 16 VID = 100 mV TA = 25°C See Note A 4 VOH VOH – High-Level Output Voltage – V VOH VOH – High-Level Output Voltage – V 5 VDD = 5 V 3 VDD = 4 V VDD = 3 V 2 ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ 1 0 –2 –4 –6 –8 IOH – High-Level Output Current – mA
PAGE 22
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS† LOW-LEVEL OUTPUT VOLTAGE vs COMMON-MODE INPUT VOLTAGE LOW-LEVEL OUTPUT VOLTAGE vs COMMON-MODE INPUT VOLTAGE 500 VDD = 5 V IOL = 5 mA 650 TA = 25°C 600 550 VID = – 100 mV 500 450 ÁÁ ÁÁ ÁÁ VID = – 1 V 350 300 0.5 1 1.5 2 2.5 3 3.5 VIC – Common-Mode Input Voltage – V TA = 25°C 450 400 VID = – 100 mV VID = – 1 V 350 VID = – 2.
PAGE 23
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS† LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT VOL VOL – Low-Level Output Voltage – V 0.9 0.8 0.7 ÌÌÌÌ ÌÌÌÌ ÌÌÌÌ 3.0 VID = – 1 V VIC = 0.5 V TA = 25°C See Note A VOL – Low-Level Output Voltage – V VOL 1.0 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT VDD = 5 V VDD = 4 V 0.6 VDD = 3 V 0.5 0.4 ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ 0.3 0.2 0.
PAGE 24
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS† COMMON-MODE INPUT VOLTAGE POSITIVE LIMIT vs SUPPLY VOLTAGE 10000 16 VDD = 10 V VIC = 5 V See Note A ÌÌ 1000 VIC – Common-Mode Input Voltage – V I IB and I IO – Input Bias and Offset Currents – pA INPUT BIAS CURRENT AND INPUT OFFSET CURRENT vs FREE-AIR TEMPERATURE IIB 100 ÌÌ ÌÌ IIO 10 1 0.
PAGE 25
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS† SLEW RATE vs FREE-AIR TEMPERATURE SLEW RATE vs SUPPLY VOLTAGE 8 8 AV = 1 VIPP = 1 V RL = 10 kΩ CL = 20 pF TA = 25°C See Figure 1 6 7 5 4 3 3 1 1 0 4 6 8 10 12 VDD – Supply Voltage – V 14 VDD = 10 V VIPP = 1 V 4 2 2 VDD = 10 V VIPP = 5.5 V 5 2 0 VDD = 5 V VIPP = 1 V VDD = 5 V VIPP = 2.
PAGE 26
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS† UNITY-GAIN BANDWIDTH vs SUPPLY VOLTAGE UNITY-GAIN BANDWIDTH vs FREE-AIR TEMPERATURE 2.5 VDD = 5 V VI = 10 mV CL = 20 pF See Figure 3 2.5 B1 – Unity-Gain Bandwidth – MHz B1 – Unity-Gain Bandwidth – MHz 3.0 2.0 1.5 1.0 – 75 VI = 10 mV CL = 20 pF TA = 25°C See Figure 3 2.0 1.5 1.
PAGE 27
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS† LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY 10 7 VDD = 10 V RL = 10 kΩ TA = 25°C ÁÁ ÁÁ 10 5 0° 10 4 30° Phase Shift AVD AVD – Large-Signal Differential Voltage Amplification 10 6 AVD 10 3 60° 10 2 90° Phase Shift 101 120° 1 150° 0.
PAGE 28
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS PHASE MARGIN vs CAPACITIVE LOAD 50° VDD = 5 V VI = 10 mV TA = 25°C See Figure 3 φm m – Phase Margin 45° 40° 35° 30° 25° VN V n – Equivalent Input Noise Voltage – nV/ Hz EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY 400 VDD = 5 V RS = 20 Ω TA = 25°C See Figure 2 300 200 100 0 0 10 20 30 40 50 60 70 80 90 100 1 CL – Capacitive Lo
PAGE 29
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 APPLICATION INFORMATION single-supply operation While the TLC272 and TLC277 perform well using dual power supplies (also called balanced or split supplies), the design is optimized for single-supply operation. This design includes an input common-mode voltage range that encompasses ground as well as an output voltage range that pulls down to ground.
PAGE 30
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 APPLICATION INFORMATION input characteristics The TLC272 and TLC277 are specified with a minimum and a maximum input voltage that, if exceeded at either input, could cause the device to malfunction. Exceeding this specified range is a common problem, especially in single-supply operation.
PAGE 31
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 APPLICATION INFORMATION output characteristics (continued) (b) CL = 130 pF, RL = NO LOAD (a) CL = 20 pF, RL = NO LOAD 2.5 V – VO + VI TA = 25°C f = 1 kHz VIPP = 1 V CL – 2.5 V (d) TEST CIRCUIT (c) CL = 150 pF, RL = NO LOAD Figure 41.
PAGE 32
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 APPLICATION INFORMATION output characteristics (continued) VDD VI + IP RP VO – C IF R2 R1 IL RL – VO VDD – VO IF + IL + IP ÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ + Rp = Ip = Pullup current required by the operational amplifier (typically 500 µA) Figure 42. Resistive Pullup to Increase VOH Figure 43.
PAGE 33
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 APPLICATION INFORMATION 10 kΩ 10 kΩ 0.016 µF 0.016 µF 10 kΩ – 10 kΩ 5V 10 kΩ 1/2 TLC272 – 1/2 TLC272 – VI 1/2 TLC272 Low Pass + + + High Pass 5 kΩ Band Pass R = 5 kΩ(3/d-1) (see Note A) NOTE A: d = damping factor, 1/Q Figure 44. State-Variable Filter 12 V VI + 1/2 TLC272 H.P. 5082-2835 + 1/2 TLC272 – 0.5 µF Mylar N.O. Reset VO – 100 kΩ Figure 45.
PAGE 34
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 APPLICATION INFORMATION VI (see Note A) 100 kΩ 1.2 kΩ 0.47 µF 4.7 kΩ – TL431 20 kΩ 1/2 TLC272 0.1 µF 1 kΩ TIP31 15 Ω + TIS193 250 µF, 25 V + – VO (see Note B) 10 kΩ 47 kΩ 0.01 µF 110 Ω 22 kΩ NOTES: A. VI = 3.5 to 15 V B. VO = 2 V, 0 to 1 A Figure 46. Logic-Array Power Supply VO (see Note A) 9V 10 kΩ 0.
PAGE 35
TLC272, TLC272A, TLC272B, TLC272Y, TLC277 LinCMOS PRECISION DUAL OPERATIONAL AMPLIFIERS SLOS091E – OCTOBER 1987 – REVISED FEBRUARY 2002 APPLICATION INFORMATION 5V VI – + 10 kΩ 1/2 TLC277 100 kΩ – – 1/2 TLC277 VO + 10 kΩ – 10 kΩ 1/2 TLC277 95 kΩ R1,10 kΩ (see Note A) + VI + –5 V NOTE B: CMRR adjustment must be noninductive. Figure 48. Low-Power Instrumentation Amplifier 5V – R 10 MΩ R 10 MΩ 1/2 TLC272 VO + VI 2C 540 pF f NOTCH + R/2 5 MΩ C 270 pF 1 2pRC C 270 pF Figure 49.
PAGE 36
PACKAGE OPTION ADDENDUM www.ti.
PAGE 37
PACKAGE OPTION ADDENDUM www.ti.
PAGE 38
PACKAGE OPTION ADDENDUM www.ti.
PAGE 39
PACKAGE OPTION ADDENDUM www.ti.
PAGE 40
PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided.
PAGE 41
PACKAGE MATERIALS INFORMATION www.ti.com 8-Jul-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TLC272ACDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLC272AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLC272BCDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLC272BIDR SOIC D 8 2500 330.
PAGE 42
PACKAGE MATERIALS INFORMATION www.ti.com 8-Jul-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TLC272ACDR SOIC D 8 2500 340.5 338.1 20.6 TLC272AIDR SOIC D 8 2500 340.5 338.1 20.6 TLC272BCDR SOIC D 8 2500 340.5 338.1 20.6 TLC272BIDR SOIC D 8 2500 340.5 338.1 20.6 TLC272CDR SOIC D 8 2500 340.5 338.1 20.6 TLC272CPWR TSSOP PW 8 2000 367.0 367.0 35.0 TLC272IDR SOIC D 8 2500 340.5 338.
PAGE 43
MECHANICAL DATA MCER001A – JANUARY 1995 – REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0°–15° 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters).
PAGE 44
PAGE 45
PAGE 46
PAGE 47
PAGE 48
PAGE 49
PAGE 50
PAGE 51
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.