Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Comparator Differential CMOS, MOS, Open drain, TTL TSSOP 14

1OUT

2OUT

2IN–

2IN+

1IN–

1IN+

3OUT

4OUT

GND

4IN+

4IN–

3IN+

3IN–

D, J, N, OR PW PACKAGE

(TOP VIEW)

3 2 1 20 19

910111213

GND

4IN+

4IN–

2IN–

2IN+

FK PACKAGE

(TOP VIEW)

2OUT

1OUT

3IN+

4OUT

1IN–

1IN+

NC – No internal connection

3IN–

3OUT

symbol (each comparator)

IN+

IN–

OUT

TLC374, TLC374Q, TLC374Y

LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS

SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Single- or Dual-Supply Operation

Wide Range of Supply Voltages

2 V to 18 V

Very Low Supply Current Drain 0.3 mA Typ

at 5 V

Fast Response Time . . . 200 ns Typ for

TTL-Level Input Step

Built-In ESD Protection

High Input Impedance . . . 10

Ω Typ

Extremely Low Input Bias Current 5 pA Typ

Ultrastable Low Input Offset Voltage

Input Offset Voltage Change at Worst-Case

Input Conditions Typically 0.23 µV/Month,

Including the First 30 Days

Common-Mode Input Voltage Range

Includes Ground

Outputs Compatible With TTL, MOS, and

CMOS

Pin-Compatible With LM339

description

These quadruple differential comparators are

fabricated using LinCMOS technology and

consist of four independent voltage comparators

designed to operate from a single power supply.

Operation from dual supplies is also possible if the

difference between the two supplies is 2 V to 18 V.

Each device features extremely high input

impedance (typically greater than 10

Ω),

allowing direct interfacing with high-impedance

sources. The outputs are n-channel open-drain

configurations and can be connected to achieve

positive-logic wired-AND relationships.

The TLC374 has internal electrostatic discharge (ESD) protection circuits and has been classified with a 1000-V

ESD rating using human body model testing. However, care should be exercised in handling this device as

exposure to ESD may result in degradation of the device parametric performance.

The TLC374C is characterized for operation from 0°C to 70°C. The TLC374I is characterized for operation from

–40° to 85°C. The TLC374M is characterized for operation over full military temperature range of

–55°C to 125°C. The TLC374Q is characterized for operation from –40°C to 125°C.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of Texas Instruments

standard warranty. Production processing does not necessarily include

testing of all parameters.

LinCMOS is a trademark of Texas Instruments Incorporated.

Summary of content (26 pages)

PAGE 1
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 D D D D D D D D D D Single- or Dual-Supply Operation Wide Range of Supply Voltages 2 V to 18 V Very Low Supply Current Drain 0.3 mA Typ at 5 V Fast Response Time . . . 200 ns Typ for TTL-Level Input Step Built-In ESD Protection High Input Impedance . . .
PAGE 2
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 AVAILABLE OPTIONS PACKAGED DEVICES SMALL OUTLINE (D) CHIP CARRIER (FK) CERAMIC DIP (J) PLASTIC DIP (N) TSSOP (PW) CHIP FORM (Y) 5 mV TLC374CD — — TLC374CN TLC374CPW TLC374Y TA VIO max AT 25°C 0°C to 70°C – 40°C to 85°C 5 mV TLC374ID — — TLC374IN — — – 55°C to 125°C 5 mV TLC374MD TLC374MFK TLC374MJ TLC374MN — — – 40°C to 125°C 5 mV TLC374QD — — TLC374QN — —
PAGE 3
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 TLC374Y chip information This chip, when properly assembled, displays characteristics similar to the TLC374C. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.
PAGE 4
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
electrical characteristics at specified free-air temperature, VDD = 5 V PARAMETER VIO Input offset voltage IIO Input offset current IIB VICR TEST CONDITIONS VIC = VICRmin min, See Note 4 TA† TLC374C MIN 25°C TYP 1 Full range VOH = 5 V VOH = 15 V VOL Low level output voltage Low-level VID = – 1 V V, IOL = 4 mA IOL Low-level output current VID = –1 V, VOL = 1.5 V IDD Supply y current (four comparators) VID = 1 V V, No load 5 1 7 1 5 5 2 25°C Full range 0 to VDD – 1.
PAGE 6
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 electrical characteristics at specified free-air temperature, VDD = 5 V, TA = 25°C (unless otherwise noted) PARAMETER TLC374Y TEST CONDITIONS VIC = VICRmin, MIN See Note 4 TYP MAX 1 5 UNIT VIO IIO Input offset voltage Input offset current 1 pA IIB VICR Input bias current 5 pA IOH VOL High-level output current 0.
PAGE 7
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 PARAMETER MEASUREMENT INFORMATION The digital output stage of the TLC374 can be damaged if it is held in the linear region of the transfer curve. Conventional operational amplifier/comparator testing incorporates the use of a servo loop that is designed to force the device output to a level within this linear region.
PAGE 8
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 PARAMETER MEASUREMENT INFORMATION Figure 2 illustrates a practical circuit for direct dc measurement of input offset voltage that does not bias the comparator into the linear region. The circuit consists of a switching-mode servo loop in which U1a generates a triangular waveform of approximately 20-mV amplitude. U1b acts as a buffer with C2 and R4 removing any residual dc offset.
PAGE 9
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 PARAMETER MEASUREMENT INFORMATION Response time is defined as the interval between the application of an input step function and the instant when the output reaches 50% of its maximum value. Response time, low-to-high-level output, is measured from the trailing edge of the input pulse. Response-time measurement at low input signal levels can be greatly affected by the input offset voltage.
PAGE 10
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 PRINCIPLES OF OPERATION LinCMOS process LinCMOS process is a linear polysilicon-gate complimentary-MOS process. Primarily designed for singlesupply applications, LinCMOS products facilitate the design of a wide range of high-performance analog functions from operational amplifiers to complex mixed-mode converters.
PAGE 11
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 PRINCIPLES OF OPERATION Input protection circuit operation Texas Instruments patented protection circuitry allows for both positive- and negative-going ESD transients. These transients are characterized by extremely fast rise times and usually low energies, and can occur both when the device has all pins open and when it is installed in a circuit.
PAGE 12
TLC374, TLC374Q, TLC374Y LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS SLCS118C – NOVEMBER 1983 – REVISED MARCH 1999 PRINCIPLES OF OPERATION INPUT CURRENT vs INPUT VOLTAGE† INPUT CURRENT vs INPUT VOLTAGE† 8 10 TA = 25°C 9 7 TA = 25°C IIII – Input Current – mA IIII – Input Current – mA 8 6 5 4 3 7 6 5 4 3 2 2 1 1 0 VDD VDD + 4 VDD + 8 VI – Input Voltage – V 0 VDD– 0.
PAGE 13
PACKAGE OPTION ADDENDUM www.ti.
PAGE 14
PACKAGE OPTION ADDENDUM www.ti.
PAGE 15
PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
PAGE 16
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TLC374CDR Package Package Pins Type Drawing SOIC SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 TLC374CNSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 TLC374CPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TLC374IDR SOIC D 14 2500 330.
PAGE 17
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TLC374CDR SOIC D 14 2500 333.2 345.9 28.6 TLC374CNSR SO NS 14 2000 367.0 367.0 38.0 TLC374CPWR TSSOP PW 14 2000 367.0 367.0 35.0 TLC374IDR SOIC D 14 2500 367.0 367.0 38.
PAGE 18
PAGE 19
PAGE 20
PAGE 21
PAGE 22
PAGE 23
PAGE 24
PAGE 25
PAGE 26
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.