Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Op-amp Multi-purpose SOIC 14

     

  µ   

   

SLOS270D − MARCH 2001 − REVISED JANUARY 2005

WWW.TI.COM

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

D Rail-To-Rail Input/Output

D Wide Bandwidth ...3 MHz

D High Slew Rate . . . 2.4 V/µs

D Supply Voltage Range . . . 2.7 V to 16 V

D Supply Current . . . 550 µA/Channel

D Low Power Shutdown Mode

DD(SHDN)

... 25 µA/Channel

D Input Noise Voltage . . . 39 nV/√Hz

D Input Bias Current...1 pA

D Specified Temperature Range

−40°C to 125°C . . . Industrial Grade

D Ultrasmall Packaging

5 or 6 Pin SOT-23 (TLV2370/1)

8 or 10 Pin MSOP (TLV2372/3)

description

The TLV237x single supply operational amplifiers provide rail-to-rail input and output capability. The TLV237x

takes the minimum operating supply voltage down to 2.7 V over the extended industrial temperature range while

adding the rail-to-rail output swing feature. The TLV237x also provides 3-MHz bandwidth from only 550 µA. The

maximum recommended supply voltage is 16 V, which allows the devices to be operated from (±8 V supplies

down to ±1.35 V) a variety of rechargeable cells.

The CMOS inputs enable use in high-impedance sensor interfaces, with the lower voltage operation making

an ideal alternative for the TLC227x in battery-powered applications. The rail-to-rail input stage further

increases its versatility. The TLV237x is the seventh member of a rapidly growing number of RRIO products

available from TI, and it is the first to allow operation up to 16-V rails with good ac performance.

All members are available in PDIP and SOIC with the singles in the small SOT-23 package, duals in the MSOP,

and quads in the TSSOP package.

The 2.7-V operation makes the TLV237x compatible with Li-Ion powered systems and the operating supply

voltage range of many micro-power microcontrollers available today including TI’s MSP430.

SELECTION OF SIGNAL AMPLIFIER PRODUCTS

†

DEVICE

(V)

(µV)

Iq/Ch

(µA)

(pA)

GBW

(MHz)

(V/µs)

SHUTDOWN

RAIL-

TO-

RAIL

SINGLES/DUALS/QUADS

TLV237x 2.7−16 500 550 1 3 2.4 Yes I/O S/D/Q

TLC227x 4−16 300 1100 1 2.2 3.6 — O D/Q

TLV27x 2.7−16 500 550 1 3 2.4 — O S/D/Q

TLC27x 3−16 1100 675 1 1.7 3.6 — — S/D/Q

TLV246x 2.7−6 150 550 1300 6.4 1.6 Yes I/O S/D/Q

TLV247x 2.7−6 250 600 2 2.8 1.5 Yes I/O S/D/Q

TLV244x 2.7−10 300 725 1 1.8 1.4 — O D/Q

†

Typical values measured at 5 V, 25°C

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications o

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

  !"#$%&'(!$" !) *+%%,"( ') $# -+./!*'(!$" 0'(,1

%$0+*() *$"#$%& ($ )-,*!#!*'(!$") -,% (, (,%&) $# ,2') ")(%+&,"()

)('"0'%0 3'%%'"(41 %$0+*(!$" -%$*,))!"5 0$,) "$( ",*,))'%!/4 !"*/+0,

(,)(!"5 $# '// -'%'&,(,%)1

Operational Amplifier

−

Summary of content (42 pages)

PAGE 1
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 D D D D D D D D D D Rail-To-Rail Input/Output Wide Bandwidth . . . 3 MHz High Slew Rate . . . 2.4 V/µs Supply Voltage Range . . . 2.7 V to 16 V Supply Current . . . 550 µA/Channel Low Power Shutdown Mode IDD(SHDN) . . . 25 µA/Channel Input Noise Voltage . . . 39 nV/√Hz Input Bias Current . . .
PAGE 2
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 FAMILY PACKAGE TABLE(1) PACKAGE TYPES NUMBER OF CHANNELS PDIP SOIC SOT-23 TSSOP MSOP TLV2370 1 8 8 6 — — Yes TLV2371 1 8 8 5 — — — TLV2372 2 8 8 — — 8 — TLV2373 2 14 14 — — 10 Yes TLV2374 4 14 14 — 14 — — TLV2375 4 16 16 — 16 — Yes DEVICE SHUTDOWN UNIVERSAL EVM BOARD Refe
PAGE 3
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 TLV237x PACKAGE PINOUTS(1) TLV2370 D OR P PACKAGE (TOP VIEW) TLV2370 DBV PACKAGE (TOP VIEW) OUT 1 6 VDD GND 2 5 SHDN IN+ 3 4 IN − TLV2371 D OR P PACKAGE (TOP VIEW) NC IN − IN + GND 1OUT 1IN − 1IN+ GND NC 1SHDN NC 1 8 2 7 3 6 4 5 NC IN − IN + GND 1 8 2 7 3 6 4 5 TLV2371 DBV PACKAGE (TOP VIEW) SHDN
PAGE 4
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V Differential input voltage, VID . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 electrical characteristics at specified free-air temperature, VDD = 2.7 V, 5 V, and 15 V (unless otherwise noted) dc performance PARAMETER TEST CONDITIONS TA MIN 25°C VIO Input offset voltage αVIO Offset voltage drift VO = VDD/2, VIC = VDD/2, RS = 50 Ω VIC = 0 to VDD−1.
PAGE 6
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 electrical characteristics at specified free-air temperature, VDD = 2.7 V, 5 V, and 15 V (unless otherwise noted) (continued) output characteristics PARAMETER TEST CONDITIONS VIC = VDD/2, IOH = −1 mA TA MIN TYP 25°C 2.55 2.58 VDD = 2.7 V Full range 2.48 25°C 4.9 VDD = 5 V Full range 4.85 25°C 14.
PAGE 7
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 electrical characteristics at specified free-air temperature, VDD = 2.7 V, 5 V, and 15 V (unless otherwise noted) (continued) dynamic performance PARAMETER UGBW TEST CONDITIONS Unity gain bandwidth RL = 2 kΩ, CL = 10 pF TA 2.
PAGE 8
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO CMRR Input offset voltage vs Common-mode input voltage Common-mode rejection ratio vs Frequency 4 Input bias and offset current vs Free-air temperature 5 VOL VOH Low-level output voltage vs Low-level output current 6, 8, 10 High-level output voltage vs High-level o
PAGE 9
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 TYPICAL CHARACTERISTICS INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE 1000 800 600 400 200 0 1000 VDD = 5 V TA = 25 °C 800 600 400 200 0 −200 −200 0.4 0.8 1.2 1.6 2 0 VICR − Common-Mode Input Voltage − V 100 VDD = 5 V, 15 V 80 VDD = 2.
PAGE 10
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 TYPICAL CHARACTERISTICS 12 TA =70°C 10 TA =25°C 8 TA =0°C 6 TA =−40°C 4 2 15 14 VDD = 15 V 12 TA = −40°C V O(PP) − Peak-to-Peak Output Voltage − V VDD = 15 V TA =125°C V OH − High-Level Output Voltage − V VOL − Low-Level Output Voltage − V 15 14 PEAK-TO-PEAK OUTPUT VOLTAGE vs FREQUENCY HIGH-LEVEL OUTPUT VOLTA
PAGE 11
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 TYPICAL CHARACTERISTICS SLEW RATE vs FREE-AIR TEMPERATURE 3.5 3 100 SR− SR+ 1 AV = 1 RL = 10 kΩ CL = 50 pF TA = 25°C 0.5 8.5 10.5 12.5 1.5 VDD = 5 V AV = 1 RL = 10 kΩ CL = 50 pF VI = 3 V 1 0 −40 −25 −10 5 14.
PAGE 12
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 TYPICAL CHARACTERISTICS INVERTING LARGE-SIGNAL RESPONSE VI 3 VDD = 5 V AV = 1 RL = 2 kΩ CL = 10 pF VI = 3 VPP TA = 25°C 2 1 0 3 2 1 0 VO 0 2 4 6 8 10 12 14 12 9 VDD = 15 V AV = −1 RL = 2 kΩ CL = 10 pF VI = 9 Vpp TA = 25°C 6 3 0 0 16 0 2 4 VDD = 5 V AV = −1 RL = 2 kΩ CL = 10 pF VI = 100 mVpp TA = 25°C 16 0.
PAGE 13
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 SHUTDOWN SUPPLY CURRENT/OUTPUT VOLTAGE vs TIME SHUTDOWN SUPPLY CURRENT/OUTPUT VOLTAGE vs TIME 10 6 VDD = 15 V AV = 1 RL = 2 kΩ CL = 10 pF VI = VDD/2 TA = 25° C 8 6 4 SHDN − Shutdown Pulse − V SHDN − Shutdown Pulse − V TYPICAL CHARACTERISTICS SHDN 2 0 5 VDD = 5 V AV = 1 RL = 2 kΩ CL = 10 pF VI = VDD/2 TA = 25° C 4 3 2
PAGE 14
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 APPLICATION INFORMATION rail-to-rail input operation The TLV237x input stage consists of two differential transistor pairs, NMOS and PMOS, that operate together to achieve rail-to-rail input operation. The transition point between these two pairs can be seen in Figure 1, Figure 2, and Figure 3 for a 2.7-V, 5-V, and 15-V supply.
PAGE 15
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 APPLICATION INFORMATION general configurations When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often required. The simplest way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier (see Figure 35).
PAGE 16
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 APPLICATION INFORMATION circuit layout considerations To achieve the levels of high performance of the TLV237x, follow proper printed-circuit board design techniques. A general set of guidelines is given in the following.
PAGE 17
µ SLOS270D − MARCH 2001 − REVISED JANUARY 2005 APPLICATION INFORMATION general power dissipation considerations For a given θJA, the maximum power dissipation is shown in Figure 37 and is calculated by the following formula: P D + Where: ǒ T Ǔ –T MAX A q JA PD = Maximum power dissipation of TLV237x IC (watts) TMAX = Absolute maximum junction temperature (150°C) TA = F
PAGE 18
PACKAGE OPTION ADDENDUM www.ti.
PAGE 19
PACKAGE OPTION ADDENDUM www.ti.
PAGE 20
PACKAGE OPTION ADDENDUM www.ti.
PAGE 21
PACKAGE OPTION ADDENDUM www.ti.
PAGE 22
PACKAGE OPTION ADDENDUM www.ti.com 18-Oct-2013 (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line.
PAGE 23
PACKAGE MATERIALS INFORMATION www.ti.com 19-Nov-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) TLV2370IDBVR SOT-23 DBV 6 3000 180.0 TLV2370IDBVT SOT-23 DBV 6 250 TLV2370IDR SOIC D 8 2500 TLV2371IDBVR SOT-23 DBV 5 TLV2371IDBVT SOT-23 DBV B0 (mm) K0 (mm) P1 (mm) 9.0 3.15 3.2 1.4 4.0 180.0 9.0 3.15 3.2 1.4 330.0 12.4 6.4 5.2 2.1 3000 178.0 9.0 3.23 3.
PAGE 24
PACKAGE MATERIALS INFORMATION www.ti.com 19-Nov-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TLV2370IDBVR SOT-23 DBV 6 3000 182.0 182.0 20.0 TLV2370IDBVT SOT-23 DBV 6 250 182.0 182.0 20.0 TLV2370IDR SOIC D 8 2500 340.5 338.1 20.6 TLV2371IDBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TLV2371IDBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TLV2371IDR SOIC D 8 2500 340.5 338.1 20.
PAGE 25
PAGE 26
PAGE 27
PAGE 28
PAGE 29
PAGE 30
PAGE 31
PAGE 32
PAGE 33
PAGE 34
PAGE 35
PAGE 36
PAGE 37
PAGE 38
PAGE 39
PAGE 40
PAGE 41
PAGE 42
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.