Universal Serial Bus OHCI Host Controller User's Guide

3.23 HC Port 2 Status and Control Register (HCRHPORTSTATUS2)
Registers www.ti.com
The HC port 2 status and control register (HCRHPORTSTATUS2) reports and controls the state of USB
host port 2. HCRHPORTSTATUS2 is shown in Figure 24 and described in Table 24 .
Figure 24. HC Port 2 Status and Control Register (HCRHPORTSTATUS2)
31 21 20 19 18 17 16
Reserved PRSC OCIC PSSC PESC CSC
R-0 R/W1C-0 R/W-0 R/W1C-0 R/W1C-0 R/W-0
15 10 9 8
Reserved LSDA/CPP PPS/SPP
R-0 R/W-0 R/W-1
7 5 4 3 2 1 0
Reserved PRS/SPR POCI/CSS PSS/SPS PES/SPE CCS/CPE
R-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
LEGEND: R/W = Read/Write; R = Read only; W1C = Write 1 to clear (writing 0 has no effect); - n = value after reset
Table 24. HC Port 2 Status and Control Register (HCRHPORTSTATUS2) Field Descriptions
Bit Field Value Description
31-21 Reserved 0 Reserved
20 PRSC Port 2 reset status change. A write of 1 clears this bit; a write of 0 has no effect.
0 Port 2 port reset status bit has not changed.
1 Port 2 port reset status bit has changed.
19 OCIC 0 Port 2 overcurrent indicator change. Because the device does not provide inputs for signaling
external overcurrent indication to the USB host controller, this bit is always 0. Overcurrent
monitoring, if required, must be handled through some other mechanism. This bit has no
relationship to the OTG controller register bits that relate to VBUS.
18 PSSC Port 2 suspend status changed. A write of 1 clears this bit; a write of 0 has no effect.
0 Port 2 port suspend status has not changed.
1 Port 2 port suspend status has changed. Suspend status is considered to have changed only after
the resume pulse, low-speed EOP, and 3-ms synchronization delays have been completed.
17 PESC Port 2 enable status change. A write of 1 clears this bit; a write of 0 has no effect.
0 Port 2 port enable status has not changed.
1 Port 2 port enable status has changed.
16 CSC Port 2 connect status change. If the DR[2] bit in the HC root hub B register (HCRHDESCRIPTORB)
is set to 1 to indicate a nonremovable USB device on port 2, this bit is set only after a root hub
reset to inform the system that the device is attached. A write of 1 clears this bit; a write of 0 has no
effect.
0 Port 2 current connect status has not changed.
1 Port 2 current connect status has changed due to a connect or disconnect event. If current connect
status is 0 when a set port reset, set port enable, or set port suspend write occurs, then this bit is
set.
15-10 Reserved 0 Reserved
9 LSDA/CPP Port 2 low-speed device attached/clear port power. This bit indicates, when read as 1, that a
low-speed device is attached to port 2. A 0 in this bit indicates a full-speed device. This bit is valid
only when port 2 current connect status is 1. The USB host controller does not control external port
power using OHCI mechanisms, so, if required, USB host port power must be controlled through
other means.
0 A write of 0 to this bit has no effect.
1 The host controller driver can write a 1 to this bit to clear the port 2 port power status.
32 Universal Serial Bus OHCI Host Controller SPRUFM8 – September 2008
Submit Documentation Feedback