Serial RapidIO (SRIO) User's Guide

www.ti.com
4.3.3 LSU Interrupt Condition Status and Clear Registers
Interrupt Conditions
For transmission, the clearing of any ICSR bit is dependent on the CPU writing to the CP register for the
queue (QUEUE n_TXDMA_CP). The CPU acknowledges the interrupt after reclaiming all available buffer
descriptors by writing the CP value. This value is compared against the port written value in the CP
register. If the values are equal, the interrupt is deasserted.
Figure 50. RX CPPI Interrupt Condition Status and Clear Registers
RX CPPI Interrupt Condition Status Register (RX_CPPI_ICSR) (Address Offset 0240h)
31 16
Reserved
R-0
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ICS15 ICS14 ICS13 ICS12 ICS11 ICS10 ICS9 ICS8 ICS7 ICS6 ICS5 ICS4 ICS3 ICS2 ICS1 ICS0
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
RX CPPI Interrupt Condition Clear Register (RX_CPPI_ICCR) (Address Offset 0248h)
31 16
Reserved
R-0
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ICC15 ICC14 ICC13 ICC12 ICC11 ICC10 ICC9 ICC8 ICC7 ICC6 ICC5 ICC4 ICC3 ICC2 ICC1 ICC0
W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0
LEGEND: R = Read only; W = Write only; - n = Value after reset
Figure 51. TX CPPI Interrupt Condition Status and Clear Registers
TX CPPI Interrupt Condition Status Register (TX_CPPI_ICSR) (Address Offset 0250h)
31 16
Reserved
R-0
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ICS15 ICS14 ICS13 ICS12 ICS11 ICS10 ICS9 ICS8 ICS7 ICS6 ICS5 ICS4 ICS3 ICS2 ICS1 ICS0
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
TX CPPI Interrupt Condition Clear Register (TX_CPPI_ICCR) (Address Offset 0258h)
31 16
Reserved
R-0
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ICC15 ICC14 ICC13 ICC12 ICC11 ICC10 ICC9 ICC8 ICC7 ICC6 ICC5 ICC4 ICC3 ICC2 ICC1 ICC0
W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0
LEGEND: R = Read only; W = Write only; - n = Value after reset
The ICSR and the ICCR for the LSUs are shown in Figure 52 . These interrupt condition registers are used
when the SRIO peripheral transmits direct I/O packets. As described in Table 36 , each of the status and
clear bits corresponds to a particular type of transaction interrupt condition for a particular LSU. The ICS
bits of LSU_ICSR indicate the occurrence of the conditions. The ICC bits of LSU_ICCR are used to clear
the corresponding ICS bits.
SPRUE13A – September 2006 Serial RapidIO (SRIO) 89
Submit Documentation Feedback