User’s Guide March 2004 Mixed-Signal Products SLOU166A
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
EVM IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use.
EVM WARNINGS AND RESTRICTIONS It is important to operate this EVM within the supply voltage range of 2.5 V to 5.5 V. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power. Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM.
Information About Cautions and Warnings Preface Read This First Information About Cautions and Warnings This book may contain cautions and warnings. This is an example of a caution statement. A caution statement describes a situation that could potentially damage your software or equipment. This is an example of a warning statement. A warning statement describes a situation that could potentially cause harm to you. The information in a caution or a warning is provided for your protection.
FCC Warning FCC Warning This equipment is intended for use in a laboratory test environment only. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference.
Contents Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Feature Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 TPA2010D1 EVM Specifications . . . . . . . . . . . .
Contents vi
Chapter 1 Introduction This chapter provides an overview of the Texas Instruments (TI) TPA2010D1 NanoFree WCSP audio amplifier evaluation module (TPA2010D1YZF EVM). It includes a list of EVM features, a brief illustrated description of the module, and a list of EVM specifications. The is TPA2010D1 EVM is completely Pb-free. The device, all the components, and the printed-circuit board are all Pb-free. In addition, no lead is used in the manufacture or assembly of the module. Topic Page 1.
Feature Highlights 1.1 Feature Highlights The TI TPA2010D1 audio amplifier evaluation module and the TI Plug-N-Play audio amplifier evaluation platform include the following features: - TPA2010D1 Low-Voltage Audio Power Amplifier Evaluation Module J 1.45 mm x 1.45 mm NanoFree WCSP J Fully-differential filter-free Class-D amplifier J Single channel, bridge-tied load (BTL) J 2.5-V to 5.5-V operation J 2.
Description 1.2 Description The TPA2010D1 audio power amplifier evaluation module is a complete, low-power single-channel audio power amplifier. It consists of the TI TPA2010D1 2.5-W low-voltage Class-D audio power amplifier IC in a very small NanoFree WCSP package, along with a small number of other parts mounted on a circuit board that is approximately one and a quarter inches square. Single in-line header pins are mounted to the underside of the module circuit board.
1-4
Chapter 2 Operation Follow the steps in this chapter to prepare the TPA2010D1 audio amplifier EVM for use. Using the TPA2010D1 EVM with the TI Plug-N-Play audio amplifier evaluation platform is a quick and easy way to connect power, signal and control inputs, and signal outputs to the EVM, using standard connectors. However, the audio amplifier evaluation module can be used stand-alone by making connections directly to the module pins, and it can be wired directly into existing circuits or equipment.
Precautions 2.1 Precautions Power Supply Input Polarity and Maximum Voltage Always ensure that the polarity and voltage of the external power connected to VCC power input connector J1, J2, and/or VDD power input connector J6 are correct. Overvoltage or reverse-polarity power applied to these terminals can open onboard soldered-in fuses and cause other damage to the platform, installed evaluation modules, and/or the power source.
Quick Start List for Platform 2.2 Quick Start List for Platform Follow these steps when using the TPA2010D1 EVM with the TI Plug-N-Play audio amplifier evaluation platform (see the platform user’s guide, SLOU011, for additional details). - Platform preparations 1) Ensure that all external power sources are set to OFF and that the platform power switch S1 is set to Off.
Quick Start List for Stand-Alone 2.3 Quick Start List for Stand-Alone Follow these steps to use the TPA2010D1 EVM stand-alone or when connecting it into existing circuits or equipment. Connections to the TPA2010D1 module header pins can be made via individual sockets, wire-wrapping, or soldering to the pins, either on the top or the bottom of the module circuit board. - Power supply 1) Ensure that all external power sources are set to OFF.
References 2.4 References 2.4.1 TPA2010D1 EVM Connected for Stereo BTL Output Figure 2−2. TPA2010D1 EVM Connected for Stereo BTL Output 5 VDC Right Audio Input (Right) 5 VDC External Mute Control Left Audio Input (Left) Note: Due to the very small size of the NanoFree WCSP IC package, the standard part number TPA2010D1 is replaced with the code AKO (Pb-free version).
TPA2010D1 Audio Power Amplifier Evaluation Module Parts List 2.4.2 TPA2010D1 EVM Schematic Diagram Figure 2−3. TPA2010D1 EVM Schematic Diagram VDD 2.5 V to 5.5 V C2 0.22 µF C3 0.22 µF R2 150 kΩ(1) A1 IN+ C1 0.22 µF IN− B1 R1 150 kΩ(1) C1 C2 SHUTDOWN R3 100 kΩ IN+ GND VDD VO− IN− VO+ SHUTDOWN PVDD C4 10 µF A2, A3 GND A3 OUT− C3 OUT+ B2 S1 GND (1) Values shown are for EVM revision A only. For non-rev A EVMs, R1 = R2 = 60.4 kΩ, A = 5 V/V. V 2.4.
TPA2010D1 EVM PCB Layers 2.4.4 TPA2010D1 EVM PCB Layers The following illustrations depict the TPA2010D1 EVM PCB layers and silkscreen. These drawings are not to scale. Gerber plots can be obtained from any TI sales office. Figure 2−4. TPA2010D1 EVM Top Layer Figure 2−5.
2-8
