User’s Guide November 2002 Mixed-Signal Products SLOU113A
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
EVM IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use.
EVM WARNINGS AND RESTRICTIONS It is important to operate this EVM within the supply voltage range of 7 V to 15 V. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power. Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM.
Preface Read This First How to Use This Manual This document contains the following chapters: - Chapter 1—Introduction - Chapter 2—Quick Start - Chapter 3—Reference Information About Cautions and Warnings This book may contain cautions and warnings. This is an example of a caution statement. A caution statement describes a situation that could potentially damage your software or equipment. This is an example of a warning statement.
Related Documentation From Texas Instruments Related Documentation From Texas Instruments J TI Plug-N-Play Audio Amplifier Evaluation Platform (literature number SLOU011) provides detailed information on the evaluation platform and its use with TI audio evaluation modules. J TPA6030A4 3-W Stereo Audio Power Amplifier With Advanced DC Volume Control (literature number SLOS395). This is the data sheet for the TPA6030A4 audio amplifier integrated circuit.
Running Title—Attribute Reference Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Feature Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.
Running Title—Attribute Reference Tables 2–1 2–2 2–3 2–4 2–5 3–1 3–2 viii Typical TI Plug-N-Play Platform Jumper and Switch Settings for the TPA6030A4 . . . . . . Typical TPA6030A4EVM Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Platform Jumper and Switch Settings for the TPA6030A4 . . . . . . . . . . . . . . . . . . . . . . . . . . . Typical TPA6030A4EVM Jumper Settings for BTL Stand-Alone . . . . . . . . . . . . . . . . . . . . .
Chapter 1 Introduction This chapter provides an overview of the Texas Instruments (TI) TPA6030A4 audio amplifier evaluation module (SLOP365). It includes a list of EVM features, a brief illustrated description of the module, and a list of EVM specifications. Topic Page 1.1 Feature Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2 1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature Highlights 1.
Description 1.2 Description The TPA6030A4 stereo 3-W audio power amplifier evaluation module is designed to demonstrate all of the different features and benefits of the TPA6030A4 amplifier. It consists of the TI TPA6030A4 stereo 3-W audio power amplifier IC along with a small number of other parts mounted on a circuit board that measures approximately 2 1/4 inches by 1 1/2 inches (Figure 1–1). Figure 1–1.
Special Notes Regarding the Data Sheet 1.4 Special Notes Regarding the Data Sheet The TPA6036A4EVM may have markings not consistent with the data sheet. Some EVMs have an incorrect supply voltage marked on them. The correct supply range is 7 V to 15 V, not 5 V to 15 V. The EVM and this user’s guide refer to the two input pins as HP and LINE, and refer to the control pin as HP/LINE. The data sheet refers to the two inputs as IN2 and IN1, respectively, and the control pin as IN2/IN1.
Chapter 2 Quick Start The steps in this chapter can be followed to quickly prepare the TPA6030A4 audio amplifier EVM for use. Using the TPA6030A4 with the TI Plug-N-Play audio amplifier evaluation platform is a quick and easy way to connect power, signal and control inputs, and signal outputs to the EVM using standard connectors.
Table 2–1. Typical TI Plug-N-Play Platform Jumper and Switch Settings for the TPA6030A4 EVM JP5 JP6 JP7 JP8 S2 S3 P-N-P Platform OFF Mode X X Note 4 X Notes: 1) X = Don’t care 2) ON = Shunt installed 3) OFF = Open 4) Set S2 to ON when signal conditioning board is installed in U1; set S2 to OFF when no signal conditioning board is installed. Table 2–2.
Precautions 2.1 Precautions Power Supply Input Polarity and Maximum Voltage Always ensure that the polarity and voltage of the external power connected to VCC power input connector J1, J2, and/or VDD power input connector J6 are correct. Overvoltage or reverse-polarity power applied to these terminals can open onboard soldered-in fuses and cause other damage to the platform, installed evaluation modules, and/or the power source.
Quick Start List for Platform 2.2 Quick Start List for Platform Follow these steps when using the TPA6030A4EVM with the TI Plug-N-Play audio amplifier evaluation platform (see the platform user’s guide, SLOU011, for additional details). Numbered callouts for selected steps are shown in Figure 2–1 and Figure 2–2: Note: The TI Plug-N-Play platform sends the input signal to both the HP and LINE inputs automatically, and only to the positive inputs.
Quick Start List for Platform - Evaluation Module Preparations Figure 2–2. Module Preparation 13 12 10 11 10) The SE jumper, J1, is used to select between the two output modes, SE and BTL. To allow the module SE/BTL control input to force the amplifier IC into a BTL output mode, set output mode jumper J1 to OFF. To keep the module amplifier IC in the single-ended output mode regardless of the control input state, set jumper J1 to ON.
Quick Start List for Stand-Alone 2.3 Quick Start List for Stand-Alone Follow these steps to use the TPA6030A4EVM stand-alone or when connecting it to existing circuits or equipment. Connections to the TPA6030A4 module header pins can be made via individual sockets, wire-wrapping, or soldering to the pins, either on the top or the bottom of the module circuit board. Numbered callouts for selected steps are shown in Figure 2–3. Figure 2–3.
Quick Start List for Stand-Alone - Evaluation Module Preparations 6) To force the EVM into a BTL output mode, set jumper J1 to OFF. To force the EVM into a SE output mode, set jumper J1 to ON. 7) To force the EVM into using the LINE inputs, set jumper J2 to OFF. To force the EVM into using HP inputs, set jumper J2 to ON.
Quick Start List for Stand-Alone Figure 2–4. TPA6030A4EVM Connected for Stereo Bridge-Tied Load (BTL) Output Audio Input Right External Shut Down Control (active low) Audio Input Left Power Supply Table 2–4. Typical TPA6030A4EVM Jumper Settings for BTL Stand-Alone Note: EVM J1 J2 J3 TPA6030A4 OFF OFF OFF ON = Shunt installed OFF = Open Figure 2–5.
Chapter 3 Reference This chapter contains reference information pertaining to the layout and schematic of the TPA6030A4EVM. Also included is the volume control table for the TPA6030A4. Topic Page 3.1 TPA6030A4EVM Layout and Schematic . . . . . . . . . . . . . . . . . . . . . . . . . 3–1 3.2 TPA6030A4 Audio Power Amplifier Evaluation Module Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4 3.3 Volume Control . . . . . . . . . . .
TPA6030A4EVM Layout and Schematic 3.1 TPA6030A4EVM Layout and Schematic Figure 3–1. TPA6030A4 EVM Top Layer Figure 3–2.
+ GND SEMAX LOUT+ NC GND LPV CC LIN2+ LOUT– BYPASS LIN2– V CC CLK VREF RIN2+ GND SEDIFF RIN2– LIN1+ VOLUME RIN1+ LIN1– IN2/IN1 SHUTDOWN RIN1– RPVCC ROUT+ ROUT– + TPA6030A4EVM Layout and Schematic Figure 3–3.
TPA6030A4 Audio Power Amplifier Evaluation Module Parts List 3.2 TPA6030A4 Audio Power Amplifier Evaluation Module Parts List Table 3–1. TPA6030A4EVM Parts List Reference Description Size EVM Qty. Manufacturer/ Part Number Distributor’s Number C9, C11, C12, C15 Capacitor, 1 µF, 80%/–20%, nonpolarized, 16 V 0805 4 Panasonic ECJ–2VF1C105Z Digi-Key PCC1849TR-ND C1, C2, C3, C4, C5, C6, C7, C8 Capacitor, 0.
Volume Control 3.3 Volume Control Table 3–2. Volume Control (VCC = 12 V, No Load, SEDIFF = 0 V, SEMAX = 5VREF) Voltage On VOLUME Pin as a Speaker Volume Headphone Volume Percenatge of 5VREF (dB) (dB) 0–10 –80.00 –86.00 10–12.6 –40.00 –46.00 12.6–15.2 –37.47 –43.47 15.2–18 –34.93 –40.93 18–20.6 –32.40 –38.40 20.6–23.4 –29.87 –35.87 23.4–26 –27.33 –33.33 26–28.6 –24.80 –30.80 28.6–31.4 –22.27 –28.27 31.4–34 –19.73 –25.73 34–36.6 –17.20 –23.20 36.6–39.4 –14.67 –20.