Datasheet
TPS57040-Q1
www.ti.com
SLVSAP4C –DECEMBER 2010–REVISED OCTOBER 2012
THERMAL INFORMATION
TPS54040-Q1
THERMAL METRIC
(1)(2)
DGQ DRC UNITS
10 PINS 10 PINS
θ
JA
Junction-to-ambient thermal resistance (standard board) 62.5 56.5
θ
JA
Junction-to-ambient thermal resistance (custom board)
(3)
57 61.5
θ
JCtop
Junction-to-case (top) thermal resistance 83 52.1
θ
JB
Junction-to-board thermal resistance 28 20.6 °C/W
ψ
JT
Junction-to-top characterization parameter 1.7 0.9
ψ
JB
Junction-to-board characterization parameter 20.1 20.8
θ
JCbot
Junction-to-case (bottom) thermal resistance 21 5.2
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
(2) Power rating at a specific ambient temperature T
A
should be determined with a junction temperature of 150°C. This is the point where
distortion starts to substantially increase. See power dissipation estimate in application section of this data sheet for more information.
(3) Test boards conditions:
(a) 3 inches x 3 inches, 2 layers, thickness: 0.062 inch
(b) 2 oz. copper traces located on the top of the PCB
(c) 2 oz. copper ground plane, bottom layer
(d) 6 thermal vias (13mil) located under the device package
ELECTRICAL CHARACTERISTICS
T
J
= –40°C to 150°C, VIN = 3.5 to 42V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY VOLTAGE (VIN PIN)
Operating input voltage 3.5 42 V
Internal undervoltage lockout
No voltage hysteresis, rising and falling 2.5 V
threshold
EN = 0 V, 25°C, 3.5 V ≤ VIN ≤ 60 V 1.5 4
Shutdown supply current
EN = 0 V, 125°C, 3.5 V ≤ VIN ≤ 60 V 1.9 6.5
μA
Operating : nonswitching supply
V
SENSE
= 0.83 V, VIN = 12 V, 25°C 116 136
current
ENABLE AND UVLO (EN PIN)
Enable threshold voltage No voltage hysteresis, rising and falling, 25°C 1.15 1.25 1.36 V
Enable threshold +50 mV –3.8
Input current μA
Enable threshold –50 mV –0.9
Hysteresis current –2.9 μA
VOLTAGE REFERENCE
T
J
= 25°C 0.792 0.8 0.808
Voltage reference V
0.784 0.8 0.816
HIGH-SIDE MOSFET
V
IN
= 3.5 V, BOOT-PH = 3 V 300
On-resistance mΩ
V
IN
= 12 V, BOOT-PH = 6 V 200 410
ERROR AMPLIFIER
Input current 50 nA
Error amplifier transconductance (g
M
) –2 μA < I
COMP
< 2 μA, V
COMP
= 1 V 97 μMhos
–2 μA < I
COMP
< 2 μA, V
COMP
= 1 V,
Error amplifier transconductance (g
M
)
26 μMhos
during slow start
V
SENSE
= 0.4 V
Error amplifier dc gain V
SENSE
= 0.8 V 10,000 V/V
Error amplifier bandwidth 2700 kHz
Error amplifier source/sink V
(COMP)
= 1 V, 100 mV overdrive ±7 μA
COMP to switch current
1.9 A/V
transconductance
Copyright © 2010–2012, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: TPS57040-Q1