Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsDev KitsPCB design board

User's Guide

SLVU268C–December 2008–Revised July 2010

TPS60150EVM-359, TPS60151EVM-359

This user's guide describes the characteristics, operation, and use of the TPS60150EVM-359 and

TPS60151EVM-359 evaluation modules (EVM). These EVMs have either the TPS60150 or TPS60151 ICs

and supporting components configured as a charge pump that provides a 5-V output. This document

includes EVM specifications, recommended test setup, test results, bill of materials (BOM), and a

schematic diagram.

Contents

1 Introduction .................................................................................................................. 2

2 Input/Output Connector Descriptions ..................................................................................... 2

3 Board Layout ................................................................................................................ 5

4 Bill of Materials and Schematic ........................................................................................... 8

List of Figures

1 TPS60150 Efficiency with V

= 3.3 V .................................................................................... 3

2 TPS60150 Startup with V

= 3.3 V and I

OUT

= 75 mA.................................................................. 3

3 TPS60150 Operation with V

= 3.3 V and I

OUT

= 150 mA ............................................................. 4

4 TPS60150 Load Transient with V

= 3.3 V and I

OUT

= 15 mA to 150 mA ........................................... 4

5 Top Assembly Layer........................................................................................................ 5

6 Top Layer .................................................................................................................... 6

7 Bottom Layer ................................................................................................................ 7

8 Schematic.................................................................................................................... 9

List of Tables

1 Typical Performance Specification Summary ........................................................................... 2

2 HPA359B Bill of Materials ................................................................................................. 8

SLVU268C–December 2008–Revised July 2010 TPS60150EVM-359, TPS60151EVM-359

Summary of content (11 pages)

PAGE 1
User's Guide SLVU268C – December 2008 – Revised July 2010 TPS60150EVM-359, TPS60151EVM-359 This user's guide describes the characteristics, operation, and use of the TPS60150EVM-359 and TPS60151EVM-359 evaluation modules (EVM). These EVMs have either the TPS60150 or TPS60151 ICs and supporting components configured as a charge pump that provides a 5-V output. This document includes EVM specifications, recommended test setup, test results, bill of materials (BOM), and a schematic diagram.
PAGE 2
Introduction 1 www.ti.com Introduction The Texas Instruments TPS6015XEVM-359 evaluation module uses either the TPS60150 or TPS60151 IC and supporting components configured as a charge pump that provides a 5-V output. The goal of the EVM is to facilitate evaluation of the TPS60150 or TPS60151 IC. 1.1 Performance Specification Summary Table 1 provides a summary of the TPS6015XEVM-359 performance specifications. All specifications are given for an ambient temperature of 25°C. Table 1.
PAGE 3
Input/Output Connector Descriptions www.ti.com 100 90 Efficiency - % 80 70 60 50 40 1 21 41 61 81 101 121 IOUT - Output Current - mA 141 Figure 1. TPS60150 Efficiency with VIN = 3.3 V Vin Vout enable Figure 2. TPS60150 Startup with VIN = 3.
PAGE 4
Input/Output Connector Descriptions www.ti.com Vin Vout Iout Figure 3. TPS60150 Operation with VIN = 3.3 V and IOUT = 150 mA Vout Iout Figure 4. TPS60150 Load Transient with VIN = 3.
PAGE 5
Board Layout www.ti.com 3 Board Layout Figure 5, Figure 6, and Figure 7 show the board layout for the HPA359 PWB. See the data sheet (SLVS888) for more specific layout guidelines. Figure 5.
PAGE 6
Board Layout www.ti.com Figure 6.
PAGE 7
Board Layout www.ti.com Figure 7.
PAGE 8
Bill of Materials and Schematic www.ti.com 4 Bill of Materials and Schematic 4.1 Bill of Materials Table 2. HPA359B Bill of Materials Count 8 -001 -002 RefDes Value Description Size Part Number MFR 2 2 C1, C3 2.2µF Capacitor, Ceramic, 10V, X5R, 10% 0603 STD STD 1 1 C2 1µF Capacitor, Ceramic, 10V, X5R, 10% 0603 STD STD 0 0 D1–D5 LW E67C Diode, LED, White, 30-mA, Common Anode P-LCC-4 LW E67C Osram 4 4 J1–J4 PTC02SAAN Header, 2-pin, 100mil spacing, (36-pin strip) 0.
PAGE 9
Bill of Materials and Schematic www.ti.com 4.2 Schematic Drawing 1 Figure 8 is the schematic for the TPS60150EVM-359. Figure 8.
PAGE 10
Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards.
PAGE 11
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.