Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsPMICsPMIC - power management - special purpose WQFN 16 (3x3)

VLDO1

TPS65000/1

VINDCDC

VINLDO2

EN_LDO2

VDCDC

10mF

2.2 Hm

10 Fm

470kW

EN_DCDC

EN_LDO1

VINLDO1

PGND

FB_DCDC

MODE

470kW

180kW

FB_LDO1

AGND

10 Fm

VLDO2

820kW

180kW

FB_LDO2 10 Fm

680W

150kW

3.3V

VLDO1

1.8V

VLDO2

2.8V

475kW

100nF

22pF

RSTSNS

100kW

RST

TRST

232kW

470kW

0.1mF

Supply

Voltage

Supervisor

Oscillator

SSCG

BandgapReference

TPS65000/01 JointFunction/Pin

TPS65001OnlyFunction/Pin

LDO1

300mA

LDO2

300mA

Step-Down

600mA

VDCDC

RST

TPS65000, TPS65001, TPS650001

TPS650003, TPS650006, TPS650061

www.ti.com

SLVS810B –JUNE 2009–REVISED AUGUST 2010

2.25 MHz Step Down Converter with Dual LDOs and SVS

Check for Samples: TPS65000, TPS65001, TPS650001, TPS650003, TPS650006, TPS650061

FEATURES

DESCRIPTION

• Step-Down Converters:

– V

Range From 2.3V to 6V

The TPS65000 and TPS65001 are single chip Power

Management ICs for portable applications. Both

– Spread Spectrum Clock (SSC) Generation

devices combine a single step-down converter with

for Reduced EMI

two low dropout regulators. The step-down converter

– 2.25MHz Fixed Frequency Operation

enters a low power mode at light load for maximum

– 600mA or 1A (TPS650061) Output Current efficiency across the widest possible range of load

currents. For low noise applications, the devices can

• LDOs:

be forced into fixed frequency PWM via a pin. The

– V

Range From 1.6V to 6V

step-down converter allows the use of a small

– Adjustable Output Voltage

inductor and capacitors to achieve a small solution

size. The step-down converter has Power Good

– Up to 300mA Output Current

status output that can be used for sequencing. The

– Separate Power Inputs and Enables

LDOs are capable of supplying 300mA, and can

• Supply Voltage Supervisor (TPS65001)

operate with an input voltage range between 1.6V

and 6V, allowing them to be supplied from the

– Manual Reset Input for Push Button

step-down converter or directly from the main battery.

– Adjustable Reset Time

The step-down converter and the LDOs have

– Adjustable Reset Voltage

separate voltage inputs and enables, allowing for

design and sequencing flexibility.

• 3mm × 3mm 16-Pin QFN (TPS65000)

• 3mm × 3mm 20-Pin QFN (TPS65001)

The TPS65000 is available in a 16-pin leadless

package (3mm × 3mm QFN).

APPLICATIONS

The TPS65001 extends functionality by adding a

• Point of Load

Supply Voltage Supervisor (SVS). The SVS allows

• Embedded Processor Power

maximum flexibility by having the reset voltage set

with two external resistors, and the reset time set by

• Cell Phones, Smart-Phones

a small external capacitor. In addition, an active low

• PDAs, Pocket PCs

Manual Reset input allows the SVS to be connected

• Portable Media Players

to a push button for external control.

The TPS65001 is available in a 20-pin leadless

package (3mm × 3mm QFN).

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2PowerPAD is a trademark of Texas Instruments.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (34 pages)

PAGE 1
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 2.25 MHz Step Down Converter with Dual LDOs and SVS Check for Samples: TPS65000, TPS65001, TPS650001, TPS650003, TPS650006, TPS650061 FEATURES 1 • 2 • • • • DESCRIPTION Step-Down Converters: – VIN Range From 2.3V to 6V – Spread Spectrum Clock (SSC) Generation for Reduced EMI – 2.25MHz Fixed Frequency Operation – 600mA or 1A (TPS650061) Output Current LDOs: – VIN Range From 1.
PAGE 2
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure.
PAGE 3
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 DISSIPATION RATINGS DEVICE PACKAGE TPS65000/01 (1) RTE / RUK TPS65000/01 (2) (1) (2) TA ≤ 25°C TA = 70°C TA = 85°C POWER RATING POWER RATING POWER RATING RqJA RqJB 270°C/W 14°C/W 370 mW 204 mW 148 mW 48.7°C/W 14°C/W 2.05 W 1.13 W 821 mW The JEDEC low-K (1s) board used to derive this data was a 3in × 3in, two-layer board with 2-ounce copper traces on top of the board.
PAGE 4
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com ELECTRICAL CHARACTERISTICS (continued) Over full operating ambient temperature range, typical values are at TA = 25° C. Unless otherwise noted, specifications apply for condition VIN = EN_LDOx = EN_DCDC = 3.6 V. External components L = 2.2 mH, COUT = 10 mF, CIN = 4.7 mF, (see the parameter measurement information).
PAGE 5
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 ELECTRICAL CHARACTERISTICS (continued) Over full operating ambient temperature range, typical values are at TA = 25° C. Unless otherwise noted, specifications apply for condition VIN = EN_LDOx = EN_DCDC = 3.6 V. External components L = 2.2 mH, COUT = 10 mF, CIN = 4.7 mF, (see the parameter measurement information).
PAGE 6
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com PIN ASSIGNMENTS TPS65000 RTE PACKAGE (TOP VIEW) 16 15 14 TPS65001 RUK PACKAGE (TOP VIEW) 13 20 1 12 2 11 10 4 9 5 6 7 18 17 16 1 15 2 14 Exposed Thermal Pad 3 Exposed Thermal Pad 3 19 13 4 12 5 11 8 6 7 8 9 10 PIN FUNCTIONS PIN NAME TPS65000 TPS65001 I/O DESCRIPTION VINDCDC 6 8 I Input voltage to DCDC converter and all other control blocks.
PAGE 7
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.
PAGE 8
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com TYPICAL CHARACTERISTICS EFFICIENCY (DCDC 600mA PFM Mode) vs OUTPUT CURRENT EFFICIENCY (DCDC 600mA PWM Mode) vs OUTPUT CURRENT 100 90 100 VOUT = 1.2V o TA = 25 C 90 VOUT = 1.2V o TA = 25 C 4.2V 80 80 3.6V 3.3V 70 6V 2.8V Efficiency - % Efficiency - % 70 5.5V 60 5V 2.3V 50 4.5V 4.2V 40 3.3V 60 6V 2.8V 50 5.5V 2.3V 40 3.6V 30 30 20 20 10 10 0 0.00001 0.0001 0.
PAGE 9
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 TYPICAL CHARACTERISTICS (continued) VINDCDC = 3.6 V o TA = 25 C VDCDC = 1.2 V Load Current = 60mA EN_DCDC = high EN_LDO1 = low EN_LDO2 = low Ch4: Load Current DCDC 20mAdiv Ch2: SW 2V/div Ch1: VDCDC 10mV/div Ch2: SW 2V/div Ch3: Load Current DCDC 20mAdiv OUTPUT VOLTAGE RIPPLE (DCDC PWM Mode) Ch1: VDCDC 10mV/div OUTPUT VOLTAGE RIPPLE (DCDC PFM Mode) t - Time - 200ns/div Figure 6.
PAGE 10
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) TPS650001 QUIESCENT CURRENT (DCDC PFM Mode) vs INPUT VOLTAGE TPS650001 QUIESCENT CURRENT (LDOx) vs INPUT VOLTAGE 20 50 18 o TA = 85 C o TA = 25 C 16 Quiescent Current - mA Quiescent Current - mA 40 30 20 TA = -40oC VOUT = 1.8V EN_DCDC = VIN Mode = GND IO =0 mA Measure time = 2 s EN_LDOx = GND 10 2.5 3 3.5 4 4.5 5 5.
PAGE 11
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 TYPICAL CHARACTERISTICS (continued) Ch2: VLDOx 20mV/div VDCDC = 1.8V DCDC Load Current = 50mA Mode = VINDCDC VINDCDC = 6V VINLDOx = 1.6 V to 2.3V to 1.6V o TA = 25 C VLDOx = 1.007V LDOx Load Current = 1mA EN_DCDC = GND t - Time - 100ms/div t - Time - 100ms/div Figure 13. Figure 14.
PAGE 12
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) Ch1: Mode 2V/div PFM to PWM TRANSITION (DCDC) VINDCDC = 3.6V o TA = 25 C DCDC Load Current = 30mA VDCDC = 1.8V Ch3: SW 2V/div Ch2: VDCDC 20mV/div VINDCDC = 3.6V VINLDOx = 3.6V o TA = 25 C LDOx Load Current = 15mA to 100mA VLDOx = 1.2V EN_DCDC = GND t - Time - 200ms/div t - Time - 4ms/div Figure 17. Figure 18.
PAGE 13
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 DETAILED DESCRIPTION Step-Down Converter The step down converter is intended to allow maximum flexibility in the end equipment. The output voltage is user selectable with a resistor network on the output. Figure 21 illustrates the necessary connections.
PAGE 14
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com Output voltage VOUT(nom) + 1% Light load PFM Mode VOUT(nom) moderate to heavy load PWM Mode Time Figure 22. PFM Voltage Positioning Pulling the MODE pin to DC ground will result in automatic transition between PFM and PWM modes to maximize efficiency.
PAGE 15
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 VLDO1 VINLDO1 RLDO1_1 θJA Diode DISCHG + EN_LDO1 CO(LD01) FB_LDO1 ZLOAD VREF(LD01) RLOD1_2 AGND PGND A P P A Figure 24. LDO Block Diagram and Output Voltage Setting The output voltages of the LDOs are set by Equation 2: VLDO1 = VFB_LDO1 x VLDO1 = 0.
PAGE 16
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com SSC On/Off Comparison from 1.5MHz to 150MHz Zoom In of SSC On/Off Comparison from 1.5MHz to 3.5MHz 70 70 RBW = 10 kHz RBW = 10 kHz 60 60 50 50 40 40 30 30 dBmV dBmV SSC ON 20 20 10 10 0 0 -10 -10 -20 -20 -30 Start 1.5 MHz Stop 150 MHz SSC OFF -30 Start 1.5 MHz Stop 3.5 MHz Figure 25. Figure 26.
PAGE 17
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 Supply Voltage Supervisor (SVS) [TPS65001 and TPS650061 Only] The SVS is made up of 4 inputs and one output. The RST pin is an active low high impedance output. The MR pin is an active low input, suitable for connecting to a push button circuit to allow manual reset generation. The RSTSNS pin is an analog input pin used for voltage comparison.
PAGE 18
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com The RSTSNS pin should be tied to VINDCDC if the reset functionality is not needed from this pin. This will cause the reset to activate only when VINDCDC is rising from 0V or when VINDCDC has dropped below UVLO. The RSTSNS pin should be connected to an external RC network to set the deglitch timing for triggering a reset when VINDCDC is below the UVLO threshold.
PAGE 19
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 OUTPUT FILTER DESIGN (INDUCTOR AND OUTPUT CAPACITOR) Inductor Selection The typical value for the converter inductor is 2.2mH output inductor. Larger or smaller inductor values in the range of 1.5mH to 3.3mH can be used to optimize the performance of the device for specific operation conditions. The selected inductor has to be rated for its dc resistance and saturation current.
PAGE 20
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com Output Capacitor Selection The advanced Fast Response voltage mode control scheme of the converter allows the use of small ceramic capacitors with a typical value of 22mF, without having large output voltage under and overshoots during heavy load transients. Ceramic capacitors having low ESR values result in lowest output voltage ripple, and therefore, are recommended.
PAGE 21
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 APPLICATION CIRCUITS TPS65000 VIN 10mF A P EN_DCDC VINDCDC MODE 2.2mH SW VDCDC 3.3V 680kW 10mF P FB_DCDC 150kW A 22pF 470kW VIN PG VLDO1 FB_LDO1 10mF P 180kW EN_LDO1 VDCDC VLDO1 1.8V 470kW A EN_LDO2 VINLDO1 VLDO2 FB_LDO2 VLDO2 2.8V 820kW 10mF P VINLDO2 A PGND AGND P 180kW A Figure 30.
PAGE 22
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 SLVS810B – JUNE 2009 – REVISED AUGUST 2010 www.ti.com TPS650001 VIN 10mF EN_DCDC VINDCDC MODE A P 2.2mH VDCDC 1.2V SW 10mF P FB_DCDC 470kW VIN PG VLDO1 FB_LDO1 10mF VLDO1 1.8V P VIN EN_LDO1 EN_LDO2 VLDO2 2.8V VLDO2 FB_LDO2 VINLDO1 10mF P VINLDO2 PGND AGND A P Figure 32. Typical TPS650001 Application Schematic TPS650061 VIN 10mF A P EN_DCDC VINDCDC MODE 2.2mH SW VDCDC 1.
PAGE 23
TPS65000, TPS65001, TPS650001 TPS650003, TPS650006, TPS650061 www.ti.com SLVS810B – JUNE 2009 – REVISED AUGUST 2010 REVISION HISTORY Changes from Original (June 2009) to Revision A Page • Added device numbers TPA650001, TPS650003, TPS650006 and TPA650061 to the data sheet. ................................... 1 • Changed the PG pin connection From: VDCDC To: VIN in the application circuit. ...............................................................
PAGE 24
PACKAGE OPTION ADDENDUM www.ti.
PAGE 25
PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
PAGE 26
PACKAGE MATERIALS INFORMATION www.ti.com 22-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing TPS650001RTER WQFN RTE 16 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS650001RTET WQFN RTE 16 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS650003RTER WQFN RTE 16 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.
PAGE 27
PACKAGE MATERIALS INFORMATION www.ti.com 22-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS650001RTER WQFN RTE 16 3000 367.0 367.0 35.0 TPS650001RTET WQFN RTE 16 250 210.0 185.0 35.0 TPS650003RTER WQFN RTE 16 3000 367.0 367.0 35.0 TPS650003RTET WQFN RTE 16 250 210.0 185.0 35.0 TPS650006RTER WQFN RTE 16 3000 367.0 367.0 35.0 TPS650006RTET WQFN RTE 16 250 210.0 185.0 35.
PAGE 28
PAGE 29
PAGE 30
PAGE 31
PAGE 32
PAGE 33
PAGE 34
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.