Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsPMICsPMIC - battery management Power management Li-Ion, Li-Po VQFN 40 (6x6) Surface-mount

TPS65021

www.ti.com

SLVS613C –OCTOBER 2005– REVISED SEPTEMBER 2011

POWER MANAGEMENT IC FOR LI-ION POWERED SYSTEMS

Check for Samples: TPS65021

FEATURES

DESCRIPTION

234

• 1.2 A, 97% Efficient Step-Down Converter for

The TPS65021 is an integrated Power Management

System Voltage (VDCDC1)

IC for applications powered by one Li-Ion or

• 1 A, Up to 95% Efficient Step-Down Converter

Li-Polymer cell, and which require multiple power

for Memory Voltage (VDCDC2)

rails. The TPS65021 provides three highly efficient,

• 900 mA, 90% Efficient Step-Down Converter

step-down converters targeted at providing the core

voltage, peripheral, I/O and memory rails in a

for Processor Core (VDCDC3)

processor based system. All three step-down

• 30 mA LDO/Switch for Real Time Clock (VRTC)

converters enter a low-power mode at light load for

• 2 × 200 mA General-Purpose LDO

maximum efficiency across the widest possible range

• Dynamic Voltage Management for Processor

of load currents. The TPS65021 also integrates two

general-purpose 200 mA LDO voltage regulators,

Core

which are enabled with an external input pin. Each

• Preselectable LDO Voltage Using Two Digital

LDO operates with an input voltage range between

Input Pins

1.5 V and 6.5 V, allowing them to be supplied from

• Externally Adjustable Reset Delay Time

one of the step-down converters or directly from the

battery. The default output voltage of the LDOs can

• Battery Backup Functionality

be digitally set to 4 different voltage combinations

• Separate Enable Pins for Inductive Converters

using the DEFLDO1 and DEFLDO2 pins. The serial

• I

C™ Compatible Serial Interface

interface can be used for dynamic voltage scaling,

masking interrupts, or for dis/enabling and setting the

• 85-μA Quiescent Current

LDO output voltages. The interface is compatible with

• Low Ripple PFM Mode

the Fast/Standard mode I

C specification, allowing

• Thermal Shutdown Protection

transfers at up to 400 kHz. The TPS65021 is

• 40-Pin 6 mm x 6 mm QFN Package

available in a 40-pin (RHA) QFN package, and

operates over a free-air temperature of -40°C to

85°C.

APPLICATIONS

• PDA

• Cellular/Smart Phone

• Internet Audio Player

• Digital Still Camera

• Digital Radio Player

• Split Supply TMS320™ DSP Family and μP

Solutions:

OMAP™1610, OMAP1710, OMAP330, XScale

Bulverde, Samsung ARM-Based Processors,

etc.

• Intel

PXA270, etc.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2TMS320, OMAP, PowerPAD are trademarks of Texas Instruments.

3Intel is a registered trademark of Intel Corporation.

C is a trademark of Philips Electronics.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (51 pages)

PAGE 1
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com POWER MANAGEMENT IC FOR LI-ION POWERED SYSTEMS Check for Samples: TPS65021 FEATURES 1 • 1.
PAGE 2
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure.
PAGE 3
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com RECOMMENDED OPERATING CONDITIONS (continued) over operating free-air temperature range (unless otherwise noted) Inductor at L1 (2) MIN NOM 2.2 3.3 CI(DCDC1) Input Capacitor at VINDCDC1 (2) 10 CO(DCDC1) Output Capacitor at VDCDC1 (2) 10 IO(DCDC2) Output current at L2 Inductor at L2 μF 2.2 (2) 10 CO(DCDC2) Output Capacitor at VDCDC2 (2) 10 22 IO(DCDC3) Output current at L3 (2) 2.2 3.
PAGE 4
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS (continued) VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted) PARAMETER ILK 4 TEST CONDITIONS MIN TYP MAX External capacitor 1 nF Resetpwron threshold VRTC falling –3% 2.4 3% Resetpwron threshold VRTC rising –3% 2.52 3% V leakage current output inactive high 0.
PAGE 5
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.
PAGE 6
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 20 33 μA 3 μA SUPPLY PINS: VBACKUP, VSYSIN, VRTC I(q) Operating quiescent current VBACKUP = 3 V, VSYSIN = 0 V; VCC = 2.
PAGE 7
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VDCDC1 STEP-DOWN CONVERTER VI Input voltage range, VINDCDC1 IO Maximum output current I(SD) Shutdown supply current in VINDCDC1 DCDC1_EN = GND 0.
PAGE 8
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VDCDC2 STEP-DOWN CONVERTER VI Input voltage range, VINDCDC2 IO Maximum output current 2.5 I(SD) Shutdown supply current in VINDCDC2 DCDC2_EN = GND 0.
PAGE 9
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VDCDC3 STEP-DOWN CONVERTER VI Input voltage range, VINDCDC3 2.5 IO Maximum output current 900 I(SD) Shutdown supply current in VINDCDC3 DCDC3_EN = GND 0.
PAGE 10
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS VINDCDC1 = VINDCDC2 = VINDCDC3 = VCC = VINLDO = 3.6 V, VBACKUP = 3 V, TA = –40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VLDO1 and VLDO2 LOW DROPOUT REGULATORS VI Input voltage range for LDO1, 2 1.5 6.5 V VO LDO1 output voltage range 1 3.3 V VO LDO2 output voltage range 1 3.
PAGE 11
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.
PAGE 12
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com TERMINAL FUNCTIONS (continued) TERMINAL NAME NO. I/O DESCRIPTION VCC 37 I Power supply for digital and analog circuitry of VDCDC1, VDCDC2, and VDCDC3 dc-dc converters. This must be connected to the same voltage supply as VINDCDC3, VINDCDC1, and VINDCDC2. Also supplies serial interface block DEFDCDC1 10 I Input signal indicating default VDCDC1 voltage, 0 = 3 V, 1 = 3.
PAGE 13
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.
PAGE 14
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com TYPICAL CHARACTERISTICS Graphs were taken using the EVM with the following inductor/output capacitor combinations: CONVERTER INDUCTOR OUTPUT CAPACITOR OUTPUT CAPACITOR VALUE VDCDC1 VLCF4020-2R2 C2012X5R0J106M 2 × 10 μF VDCDC2 VLCF4020-2R2 C2012X5R0J106M 2 × 10 μF VDCDC3 VLF4012AT-2R2M1R5 C2012X5R0J106M 2 × 10 μF Table 1.
PAGE 15
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com DCDC2: EFFICIENCY vs OUTPUT CURRENT DCDC2: EFFICIENCY vs OUTPUT CURRENT VI = 2.5 V VI = 3.8 V Efficiency - % Efficiency - % VI = 3.8 V VI = 4.2 V VI = 4.2 V VI = 2.5 V VI = 5 V VI = 5 V o o TA = 25 C VO = 1.8 V PWM Mode TA = 25 C VO = 1.8 V PWM / PFM Mode 0.01 0.1 10 1 100 1k 10 k 0.01 0.1 10 1 IO - Output Current - mA 100 1k 10 k IO - Output Current - mA Figure 3. Figure 4.
PAGE 16
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com DCDC3: EFFICIENCY vs OUTPUT CURRENT VDCDC1 LINE TRANSIENT RESPONSE Ch1 = VI Ch2 = VO Efficiency - % VI = 3 V C1 High 4.74 V VI = 3.8 V VI = 2.5 V C1 Low 3.08 V VI = 4.2 V C2 PK-PK 85 mV VI = 5 V C2 Mean 3.2957 V IO = 100 mA VI = 3.6 V to 4.7 V VO = 3 V PWM Mode o TA = 25 C VO = 1.3 V Low Ripple PFM Mode 0.01 0.1 10 1 IO - Output Current - mA Figure 7. Figure 8.
PAGE 17
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com VDCDC1 LOAD TRANSIENT RESPONSE VDCDC2 LOAD TRANSIENT RESPONSE Ch2 = VO Ch4 = IO Ch2 = VO Ch4 = IO C4 High 1.09 A C4 High 830 mA C4 Low 120 mA C4 Low 90 mA C2 PK-PK 188 mV C2 PK-PK 80 mV C2 Mean 3.3051 V C2 Mean 1.7946 V IO = 100 mA to 800 mA VI = 3.8 V IO = 120 mA to 1080 mA VI = 3.8 V VO = 1.8 V PWM Mode VO = 3.3 V PWM Mode Figure 11. Figure 12.
PAGE 18
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com VDCDC2 OUTPUT VOLTAGE RIPPLE VO = 1.8 V VI = 3.8 V IO = 1 mA o TA = 25 C Low Ripple PFM Mode VDCDC2 OUTPUT VOLTAGE RIPPLE VI = 3.8 V VO = 1.8 V IO = 1 mA TA = 25oC PWM Mode C2 PK-PK 7.7 mV C2 Mean 1.79955 mV Figure 15. Figure 16. STARTUP VDCDC1, VDCDC2, AND VDCDC3 STARTUP LDO1 AND LDO2 ENABLE ENABLE VDCDC1 LDO1 VDCDC2 LDO2 VDCDC3 Figure 17. 18 Figure 18.
PAGE 19
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com LDO1 LINE TRANSIENT RESPONSE Ch1 = VI Ch2 = VO IO = 25 mA VO = 1.1 V o TA = 25 C LDO2 LINE TRANSIENT RESPONSE C1 High 3.83 V Ch1 = VI Ch2 = VO IO = 25 mA VO = 3.3 V TA = 25oC C1 Low 3.29 V C1 Low 3.99 V C2 PK-PK 6.2 mV C2 PK-PK 6.1 mV C2 Mean 1.09702 V Ch1 = VI Ch2 = VO C2 Mean 3.29828 V Figure 19. Figure 20. VRTC LINE TRANSIENT RESPONSE LDO1 LOAD TRANSIENT RESPONSE IO = 10 mA VO = 3 V o TA = 25 C C1 High 4.
PAGE 20
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com LDO2 LOAD TRANSIENT RESPONSE VRTC LOAD TRANSIENT RESPONSE C4 High 47.8 mA C4 High 21.4 mA C4 Low -2.9 mA C4 Low -1.4 mA C2 PK-PK 40.4 mV C2 PK-PK 76 mV C2 Mean 3.29821 V VI = 4 V VO = 3.3 V o TA = 25 C Ch2 = VO Ch4 = IO C2 Mean 2.9762 V Ch2 = VO Ch4 = IO Figure 23. 20 VI = 3.8 V VO = 3 V o TA = 25 C Figure 24.
PAGE 21
TPS65021 www.ti.com SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 DETAILED DESCRIPTION VRTC OUTPUT AND OPERATION WITH OR WITHOUT BACKUP BATTERY The VRTC pin is an always-on output, intended to supply up to 30 mA to a permanently required rail. This is the VCC_BATT rail of the Intel® PXA270 Bulverde processor for example. In applications using a backup battery, the backup voltage can be either directly connected to the TPS65021 VBACKUP pin if a Li-Ion cell is used, or via a boost converter (e.g.
PAGE 22
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 VSYSIN Vref V_VSYSIN priority #1 www.ti.com VCC VBACKUP Vref V_VBACKUP priority #2 V_VSYSIN V_VBACKUP EN VRTC LDO priority #3 VRTC Vref A. V_VSYSIN, V_VBACKUP thresholds: falling = 2.55 V, rising = 2.65 V ±3% B. RESPWRON thresholds: falling = 2.4 V, rising = 2.52 V ±3% RESPWRON Figure 25. STEP-DOWN CONVERTERS, VDCDC1, VDCDC2, and VDCDC3 The TPS65021 incorporates three synchronous step-down converters operating typically at 1.
PAGE 23
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com During PWM operation, the converters use a unique fast response voltage mode controller scheme with input voltage feed-forward to achieve good line and load regulation allowing the use of small ceramic input and output capacitors. At the beginning of each clock cycle initiated by the clock signal, the P-channel MOSFET switch is turned on. The inductor current ramps up until the comparator trips and the control logic turns off the switch.
PAGE 24
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com These control methods reduce the quiescent current to typically 14 μA per converter, and the switching activity to a minimum, thus achieving the highest converter efficiency. Setting the comparator thresholds at the nominal output voltage at light load current results in a low output voltage ripple. The ripple depends on the comparator delay and the size of the output capacitor.
PAGE 25
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com LOW DROPOUT VOLTAGE REGULATORS The low dropout voltage regulators are designed to operate well with low value ceramic input and output capacitors. They operate with input voltages down to 1.5 V. The LDOs offer a maximum dropout voltage of 300 mV at rated output current. Each LDO supports a current limit feature.
PAGE 26
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com SYSTEM RESET + CONTROL SIGNALS The RESPWRON signal can be used as a global reset for the application. It is an open drain output. The RESPWRON signal is generated according to the power good comparator of VRTC, and remains low for tnrespwron seconds after VRTC has risen above 2.52 V (falling threshold is 2.4 V, 5% hysteresis). tnrespwron is set by an external capacitor at the TRESPWRON pin. 1 nF gives typically 100 ms.
PAGE 27
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com TIMING DIAGRAMS HOT_RESET tDEGLITCH RESPWRON VO DCDC3 tNRESPWRON default voltage any voltage set 2 with I C interface Figure 26. HOT_RESET Timing VCC 1.9 V 0.8 V 2.35 V 1.9 V 1.2 V 2.47 V UVLO* 2.52 V VRTC 2.4 V 3V RESPWRON tNRESPWRON DCDCx_EN Ramp Within 800 ms VODCDCx 1.8 V slope depending on load LDO_EN VOLDOx 1.5 V *... Internal Signal VSYSIN = VBACKUP = GND; VINLDO = VCC Figure 27.
PAGE 28
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com VCC RESPWRON tNRESPWRON DCDC1_EN DCDC2_EN 3.3 V or 3 V VODCDC1 Ramp Within 800 ms VODCDC2 Ramp Within 800 ms 2.5 V or 1.8 V Ramp Within 800 ms DEFCORE register Default Value Set Higher Output Voltage for DCDC3 GO bit in CON_CTRL2 Cleared Automatically Automatically Set to Default Value DCDC3_EN VODCDC3 1.3 V or 1.55 V Ramp Within 800 ms 1.3 V or 1.
PAGE 29
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com whenever the clock line is high. There is one clock pulse per bit of data. Each data transfer is initiated with a start condition and terminated with a stop condition. When addressed, the TPS65021 device generates an acknowledge bit after the reception of each byte. The master device (microprocessor) must generate an extra clock pulse that is associated with the acknowledge bit.
PAGE 30
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com SCLK SDAT A6 Start A0 R/W ACK 0 0 R0 R7 A6 ACK A0 R/W ACK 1 0 0 Register Address Slave Address D0 D7 ACK Slave Drives the Data Slave Address Stop Master Drives ACK and Stop Repeated Start Note: SLAVE = TPS65020 Figure 32.
PAGE 31
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.
PAGE 32
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com PGOODZ.
PAGE 33
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com MASK.
PAGE 34
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com CON_CTRL.
PAGE 35
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com CON_CTRL2. Register Address: 05h (read/write) CON_CTRL2 Bit name and function Default Default value loaded by: Read/Write B7 B6 GO Core adj allowed 0 1 UVLO + DONE UVLO R/W R/W B5 0 Default Value: 40h B4 0 B3 B2 B1 B0 DCDC2 discharge DCDC1 discharge DCDC3 discharge 0 0 0 UVLO UVLO UVLO R/W R/W R/W 0 The CON_CTRL2 register can be used to take control the inductive converters.
PAGE 36
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com DEFCORE.
PAGE 37
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.
PAGE 38
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com LDO_CTRL.
PAGE 39
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com A more conservative approach is to select the inductor current rating just for the maximum switch current of the TPS65021 (2 A for the VDCDC1 and VDCDC2 converters, and 1.5 A for the VDCDC3 converter). The core material from inductor to inductor differs and has an impact on the efficiency especially at high switching frequencies. See Table 4 and the typical applications for possible inductors. Table 4.
PAGE 40
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com Table 5.
PAGE 41
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com VRTC Output The VRTC output is typically connected to the Vcc_Batt pin of a Intel® PXA270 processor. During power-up of the processor, the TPS65021 internally switches from the LDO or the backup battery to the system voltage connected at the VSYSIN pin (see Figure 25). It is required to add a capacitor of 4.7-μF minimum to the VRTC pin, even the output may be unused.
PAGE 42
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com APPLICATION INFORMATION Layout Considerations As for all switching power supplies, the layout is an important step in the design. Proper function of the device demands careful attention to PCB layout. Care must be taken in board layout to get the specified performance. If the layout is not carefully done, the regulators may show poor line and/or load regulation, and stability issues as well as EMI problems.
PAGE 43
TPS65021 SLVS613C – OCTOBER 2005 – REVISED SEPTEMBER 2011 www.ti.com TYPICAL CONFIGURATION FOR THE Intel® PXA270 BULVERDE PROCESSOR Vcc_IO Vcc PWRFAIL 10 R nBatt_Fault Vcc 1 mF 10 mF 10 mF 10 mF LOW_BATT VINDCDC1 GPIOx VRTC Vcc_Batt DCDC2_EN VINDCDC2 SYS_EN DCDC1_EN VINDCDC3 VDCDC1 TPS65021 Vcc L1 2.2 mH PWRFAIL_SNS LOWBAT_SNS 2.2 mH Vcc_IO 3 V; 3.3 V Vcc_LCD 1.8 V; 2.5 V; 3 V; 3.3 V Vcc_BB 1.8 V; 2.5 V; 3 V; 3.3 V Vcc_MEM 1.8 V; 2.5 V; 3 V; 3.3 V Vcc_USIM 1.
PAGE 44
PACKAGE OPTION ADDENDUM www.ti.
PAGE 45
PACKAGE OPTION ADDENDUM www.ti.
PAGE 46
PACKAGE MATERIALS INFORMATION www.ti.com 24-Jul-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS65021RHAR VQFN RHA 40 2500 330.0 16.4 6.3 6.3 1.1 12.0 16.0 Q2 TPS65021RHAT VQFN RHA 40 250 180.0 16.4 6.3 6.3 1.1 12.0 16.
PAGE 47
PACKAGE MATERIALS INFORMATION www.ti.com 24-Jul-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS65021RHAR VQFN RHA 40 2500 367.0 367.0 38.0 TPS65021RHAT VQFN RHA 40 250 210.0 185.0 35.
PAGE 48
PAGE 49
PAGE 50
PAGE 51
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.