Datasheet




SGLS264A − SEPTEMBER 2004 − REVISED JUNE 2008
3
www.ti.com
electrical characteristics over recommended operating free-air temperature range,
V
I
= V
O(typ)
+ 1 V, I
O
= 1 mA, C
o
= 1 µF (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V
I
Input voltage (see Note 2)
I
O
= 3 mA 1.8 5.5 V
V
I
Input voltage (see Note 2)
I
O
= 10 mA 2 5.5 V
I
O
Continuous output current (see Note 3) 0 10 mA
T
J
Operating junction temperature, T
J
-40 125 °C
TPS79718
T
A
= 25°C, 2.8 V < V
I
< 5.5 V 1.8
V
TPS79718
T
J
= −40°C to 125°C, 2.8 V < V
I
< 5.5 V 1.71 1.89
V
Output voltage (10 µA to 10 mA Load)
TPS79730
T
A
= 25°C, 4 V < V
I
< 5.5 V 3
V
Output voltage (10 µA to 10 mA Load)
(see Note 4)
TPS79730
T
J
= −40°C to 125°C, 4 V < V
I
< 5.5 V 2.880 3.12
V
(see Note 4)
TPS79733
T
A
= 25°C, 4.3 V < V
I
< 5.5 V 3.3
V
TPS79733
T
J
= −40°C to 125°C, 4.3 V < V
I
< 5.5 V 3.168 3.432
V
Quiescent current (GND current) (see Note 4)
T
A
= 25°C, 0 µA < I
O
< 10 mA 1.2
A
Quiescent current (GND current) (see Note 4)
T
J
= −40°C to 125°C, I
O
= 10 mA 5
µA
Load regulation T
A
= 25°C, I
O
= 1 µA to 10 mA 17 mV
Output voltage line regulation (∆V
O
/V
O
(see Note 4)
V
O
+ 1 V < V
I
≤ 5.5 V, T
A
= 25°C 0.15
%/V
Output voltage line regulation (∆V
O
/V
O
)
(see Note 4)
V
O
+ 1 V < V
I
≤ 5.5 V, T
J
= −40°C to 125°C 0.8
%/V
Output noise voltage (TPS79718)
BW = 200 Hz to 100 kHz, C
o
= 10 µF,
I
O
= 10 mA, T
A
= 25°C
600 µV
RMS
Output current limit V
O
= 0 V, See Note 4 190 300 mA
Power supply ripple rejection (TPS79718)
f = 100 Hz, C
o
= 10 µF,
I
O
= 10 mA, T
A
= 25°C
50 dB
TPS79730
I
O
= 10 mA, T
A
= 25°C 110
Dropout voltage (see Note 5)
TPS79730
I
O
= 10 mA, T
J
= −40°C to 125°C 400
mV
Dropout voltage (see Note 5)
TPS79733
I
O
= 10 mA, T
A
= 25°C 105
mV
TPS79733
I
O
= 10 mA, T
J
= −40°C to 125°C 400
Minimum input voltage for valid PG I
O(PG)
= 100µA, V
(PG)
≥ 0.8 V 1.2 V
PG trip threshold voltage V
O
decreasing 82 90 96 %V
O
PG output low voltage V
I
= 1.4 V, I
O(PG)
= 100 µA 0.14 0.4 V
PG leakage current V
(PG)
= 5 V 0.1 nA
NOTES: 2. To calculate the minimum input voltage for your maximum output current, use the following formula:
V
I
(min) = V
O
(max) + V
DO
(max load)
3. Continuous output current is limited by internal protection circuitry, but it is not recommended that the device operate under
conditions beyond those specified in this table for extended periods of time.
4. The minimum IN operating voltage is 1.8 V or V
O
(typ) + 1 V, whichever is greater. The maximum IN voltage is 5.5 V. There is no
minimum output current requirement and the maximum output current is 10 mA.
5. IN voltage equals V
O
(typ) −100 mV; The TPS79730 input voltage is set to 2.9 V and the TPS79733 input voltage is set to 3.2 V. The
TPS79718 dropout voltage is limited by input voltage range limitations.