Datasheet

1
FEATURES
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
EN
C1+
V+
C1-
C2+
C2-
V-
DOUT2
RIN2
ROUT2
FORCEOFF
V
CC
GND
DOUT1
RIN1
ROUT1
FORCEON
DIN1
DIN2
INVALID
DESCRIPTION/ORDERING INFORMATION
TRS3223-Q1
www.ti.com .......................................................................................................................................................................................... SLLS950 – SEPTEMBER 2008
3-V To 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ± 15-kV ESD PROTECTION
PW PACKAGE
• Qualified for Automotive Applications
(TOP VIEW)
• RS-232 Bus-Pin ESD Protection Exceeds
± 15 kV Using Human-Body Model (HBM)
• Meets or Exceeds the Requirements of
TIA/EIA-232-F and ITU v.28 Standards
• Operates With 3-V to 5.5-V V
CC
Supply
• Operates up to 250 kbit/s
• Two Drivers and Two Receivers
• Low Standby Current . . . 1 µ A Typical
• External Capacitors . . . 4 × 0.1 µ F
• Accepts 5-V Logic Input With 3.3-V Supply
The TRS3223 consists of two line drivers, two line receivers, and a dual charge-pump circuit with ± 15-kV ESD
protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of
TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the
serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to
5.5-V supply. The device operates at data signaling rates up to 250 kbit/s and a maximum of 30-V/ µ s driver
output slew rate.
Flexible control options for power management are available when the serial port is inactive. The
auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of
operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is
set low and EN is high, both drivers and receivers are shut off, and the supply current is reduced to 1 µ A.
Disconnecting the serial port or turning off the peripheral drivers causes auto-powerdown to occur.
Auto-powerdown can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown enabled,
the device is activated automatically when a valid signal is applied to any receiver input. The INVALID output is
used to notify the user if an RS-232 signal is present at any receiver input. INVALID is high (valid data) if any
receiver input voltage is greater than 2.7 V or less than – 2.7 V, or has been between – 0.3 V and 0.3 V for less
than 30 µ s. INVALID is low (invalid data) if the receiver input voltage is between – 0.3 V and 0.3 V for more than
30 µ s. See Figure 4 for receiver input levels.
ORDERING INFORMATION
(1)
T
A
PACKAGE
(2)
ORDERABLE PART NUMBER TOP-SIDE MARKING
– 40 ° C to 125 ° C TSSOP – PW Reel of 2000 TRS3223QPWRQ1 T3223
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com .
(2) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging .
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2008, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.