Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - analogue switches VQFN 16

TS3L110

QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH

DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER

SCDS176 − SEPTEMBER 2004

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

D Wide Bandwidth (BW = 500 MHz Typ)

D Low Crosstalk (X

TALK

= −30 dB Typ)

D Bidirectional Data Flow, With Near-Zero

Propagation Delay

D Low and Flat ON-State Resistance

= 4 W Typ, r

on(flat)

= 1 W)

D Switching on Data I/O Ports (0 to 5 V)

D V

Operating Range From 3 V to 3.6 V

D I

off

Supports Partial-Power-Down Mode

Operation

D Data and Control Inputs Have Undershoot

Clamp Diodes

D Latch-Up Performance Exceeds 100 mA Per

JESD 78, Class II

D ESD Performance Tested Per JESD 22

− 2000-V Human-Body Model

(A114-B, Class II)

− 1000-V Charged-Device Model (C101)

D Suitable for Both 10 Base-T/100 Base-T

Signaling

D, DBQ, DGV, OR PW PACKAGE

(TOP VIEW)

GND

RGY PACKAGE

(TOP VIEW)

116

GND

description/ordering information

The TI TS3L110 LAN switch is a 4-bit 1-of-2 multiplexer/demultiplexer with a single switch-enable (E) input.

When E

is low, the switch is enabled, and the I port is connected to the Y port. When E is high, the switch is

disabled, and the high-impedance state exists between the I and Y ports. The select (S) input controls the data

path of the multiplexer/demultiplexer.

ORDERING INFORMATION

PACKAGE

†

ORDERABLE

PART NUMBER

TOP-SIDE

MARKING

QFN − RGY Tape and reel TS3L110RGYR TK110

SOIC D

Tube TS3L110D

TS3L110

SOIC − D

Tape and reel TS3L110DR

TS3L110

−40°C to 85°C

SSOP (QSOP) − DBQ Tape and reel TS3L110DBQR TK110

40 C

85 C

TSSOP PW

Tube TS3L110PW

TK110

TSSOP − PW

Tape and reel TS3L110PWR

TK110

TVSOP − DGV Tape and reel TS3L110DGVR TK110

†

Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines

are available at www.ti.com/sc/package.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of Texas Instruments

standard warranty. Production processing does not necessarily include

testing of all parameters.

Summary of content (26 pages)

PAGE 1
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 D Wide Bandwidth (BW = 500 MHz Typ) D Low Crosstalk (XTALK = −30 dB Typ) D Bidirectional Data Flow, With Near-Zero D D 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC E ID0 ID1 YD IC0 IC1 YC IA0 IA1 YA IB0 IB1 YB 1 16 15 E 14 ID0 2 3 13 ID1 12 YD 4 5 11 IC0 10 IC1 6 7 8 9 YC S IA0 IA1 YA IB0 IB1 YB GND VCC RGY PACKAGE (TOP VIEW) D, DBQ,
PAGE 2
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 description/ordering information (continued) This device can be used to replace mechanical relays in LAN applications. This device has low and flat ron, wide bandwidth, and low crosstalk, making it suitable for 10 Base-T, 100 Base-T, and various other LAN applications.
PAGE 3
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 logic diagram (positive logic) 2 4 IA0 YA 3 IA1 YB 7 5 IB0 6 IB1 11 9 YC 10 YD 12 14 13 S IC0 IC1 ID0 ID1 1 15 Control Logic E POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3
PAGE 4
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V Control input voltage range, VIN (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 electrical characteristics over recommended VCC = 3.3 V + 0.3 V (unless otherwise noted) PARAMETER operating free-air TEST CONDITIONS temperature range, TYP† MAX UNIT −1.8 V MIN VIK E, S VCC = 3.6 V, IIN = −18 mA IIH E, S VCC = 3.6 V, VIN = 5.5 V ±1 μA IIL E, S VCC = 3.6 V, VIN = GND ±1 μA VCC = 0, VO = 0 to 5.
PAGE 6
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 OPERATING CHARACTERISTICS 0 0 Phase −10 −1 −20 Gain −30 −3 J −40 −4 −5 Y Phase (Deg) Gain (dB) −2 −50 −60 −6 −70 −7 1 10 100 700 Frequency (MHz) J Y Phase at 627 MHz, −36 Degrees Gain −3 dB at 627 MHz Figure 1.
PAGE 7
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 OPERATING CHARACTERISTICS 0 180 −10 160 −20 140 J Y −40 100 Phase −50 80 −60 60 Phase (Deg) 120 Gain −70 40 −80 20 −90 1 10 0 700 100 Frequency (MHz) Phase at 250 MHz, 137.92 Degrees Gain −26 dB at 250 MHz Figure 3.
PAGE 8
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 PARAMETER MEASUREMENT INFORMATION FOR ENABLE AND DISABLE TIMES VCC Input Generator VIN 50 Ω 50 Ω VG1 TEST CIRCUIT DUT 2 × VCC Input Generator VI S1 RL VO Open GND 50 Ω 50 Ω VG2 CL (see Note A) RL TEST VCC S1 RL VI CL VΔ tPLZ/tPZL 3.3 V ± 0.3 V 2 × VCC 200 Ω GND 10 pF 0.3 V tPHZ/tPZH 3.3 V ± 0.3 V GND 200 Ω VCC 10 pF 0.
PAGE 9
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 PARAMETER MEASUREMENT INFORMATION FOR SKEW VCC Input Generator VIN 50 Ω 50 Ω VG1 TEST CIRCUIT DUT 2 × VCC Input Generator VI RL VO S1 Open GND 50 Ω 50 Ω VG2 CL (see Note A) RL TEST VCC S1 RL VIN (see Note B) CL tsk(p) 3.3 V ± 0.3 V GND 200 Ω VCC or GND 10 pF 3.5 V Data Input 2.5 V 1.5 V tPLH tPHL VOH 0.
PAGE 10
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 PARAMETER MEASUREMENT INFORMATION EXT TRIGGER BIAS Network Analyzer (HP8753ES) VBIAS P1 P2 VCC IA0 YA CL = 10 pF (see Note A) RL = 100 Ω S DUT VS E VE NOTE A: CL includes probe and jig capacitance. Figure 7. Test Circuit for Frequency Response (BW) Frequency response is measured at the output of the ON channel.
PAGE 11
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 PARAMETER MEASUREMENT INFORMATION EXT TRIGGER BIAS Network Analyzer (HP8753ES) VBIAS P1 P2 VCC IA0 YA S RL = 100 Ω CL = 10 pF (see Note A) RL = 100 Ω CL = 10 pF (see Note A) 50 Ω (see Note B) VS E DUT VE YB IB0 NOTES: A. CL includes probe and jig capacitance. B. A 50-Ω termination resistor is needed to match the loading of the network analyzer.
PAGE 12
TS3L110 QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER SCDS176 − SEPTEMBER 2004 PARAMETER MEASUREMENT INFORMATION EXT TRIGGER BIAS Network Analyzer (HP8753ES) VBIAS P1 P2 VCC IA0 YA S RL = 100 Ω CL = 10 pF (see Note A) RL = 100 Ω CL = 10 pF (see Note A) DUT VS IA1 E VE 50 Ω (see Note B) NOTES: A. CL includes probe and jig capacitance. B. A 50-Ω termination resistor is needed to match the loading of the network analyzer.
PAGE 13
PACKAGE OPTION ADDENDUM www.ti.
PAGE 14
PACKAGE OPTION ADDENDUM www.ti.
PAGE 15
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TS3L110DGVR Package Package Pins Type Drawing TVSOP SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DGV 16 2000 330.0 12.4 6.8 4.0 1.6 8.0 12.0 Q1 TS3L110DR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 TS3L110PWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.
PAGE 16
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TS3L110DGVR TVSOP DGV 16 2000 367.0 367.0 35.0 TS3L110DR SOIC D 16 2500 333.2 345.9 28.6 TS3L110PWR TSSOP PW 16 2000 367.0 367.0 35.0 TS3L110RGYR VQFN RGY 16 3000 367.0 367.0 35.
PAGE 17
MECHANICAL DATA MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0°– 8° 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters.
PAGE 18
PAGE 19
PAGE 20
PAGE 21
PAGE 22
PAGE 23
PAGE 24
PAGE 25
PAGE 26
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.