Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - analogue switches DSBGA 8

DCU PACKAGE

(TOP VIEW)

NO1

COM1

IN2

GND

COM2

IN1

NO2

YZT OR YZP PACKAGE

(BOTTOM VIEW)

GND

IN1

COM2

IN2

COM1

NO1

NO2

TS5A23166

www.ti.com

SCDS196G –MAY 2005–REVISED FEBRUARY 2013

0.9-Ω DUAL SPST ANALOG SWITCH

5-V/3.3-V 2-CHANNEL ANALOG SWITCH

Check for Samples: TS5A23166

FEATURES

APPLICATIONS

• Isolation in Powered-Down Mode, V

= 0 • Cell Phones

• Low ON-State Resistance (0.9 Ω) • PDAs

• Control Inputs Are 5.5-V Tolerant • Portable Instrumentation

• Low Charge Injection • Audio and Video Signal Routing

• Excellent ON-State Resistance Matching • Low-Voltage Data-Acquisition Systems

• Low Total Harmonic Distortion (THD) • Communication Circuits

• 1.65-V to 5.5-V Single-Supply Operation • Modems

• Latch-Up Performance Exceeds 100 mA Per • Hard Drives

JESD 78, Class II

• Computer Peripherals

• ESD Performance Tested Per JESD 22

• Wireless Terminals and Peripherals

– 2000-V Human-Body Model

(A114-B, Class II)

– 1000-V Charged-Device Model (C101)

DESCRIPTION/ORDERING INFORMATION

The TS5A23166 is a dual single-pole single-throw (SPST) analog switch that is designed to operate from 1.65 V

to 5.5 V. The device offers a low ON-state resistance and an excellent channel-to-channel ON-state resistance

matching. The device has excellent total harmonic distortion (THD) performance and consumes very low power.

These features make this device suitable for portable audio applications.

Table 1. ORDERING INFORMATION

ORDERABLE

PACKAGE

(1) (2)

TOP-SIDE MARKING

(3)

PART NUMBER

NanoFree™ – WCSP (DSBGA)

TS5A23166YZTR

0.23-mm Large Bump – YZT (Pb-free)

Tape and reel JM_

–40°C to 85°C NanoFree™ – WCSP (DSBGA)

TS5A23166YZPR

0.23-mm Large Bump – YZP (Pb-free)

VSSOP – DCU (Pb-free) Tape and reel TS5A23166DCUR JAM_

(1) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.

(2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI

website at www.ti.com.

(3) The actual top-side marking has one additional character that designates the assembly/test site.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (29 pages)

PAGE 1
TS5A23166 www.ti.com SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 0.9-Ω DUAL SPST ANALOG SWITCH 5-V/3.3-V 2-CHANNEL ANALOG SWITCH Check for Samples: TS5A23166 FEATURES APPLICATIONS • • • • • • • • • • • • • • • • • • 1 • Isolation in Powered-Down Mode, V+ = 0 Low ON-State Resistance (0.9 Ω) Control Inputs Are 5.5-V Tolerant Low Charge Injection Excellent ON-State Resistance Matching Low Total Harmonic Distortion (THD) 1.65-V to 5.
PAGE 2
TS5A23166 SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 www.ti.com SUMMARY OF CHARACTERISTICS (1) Dual Single Pole, Single Throw (2 × SPST) Configuration Number of channels 2 ON-state resistance (ron) 0.9 Ω ON-state resistance match (Δron) 0.1 Ω ON-state resistance flatness (ron(flat)) 0.25 Ω Turn-on/turn-off time (tON/tOFF) 7.
PAGE 3
TS5A23166 www.ti.com SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 Electrical Characteristics for 5-V Supply (1) V+ = 4.5 V to 5.5 V, TA = –40°C to 85°C (unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS TA V+ MIN TYP MAX 0 V+ UNIT Analog Switch Analog signal range VCOM, VNO Peak ON resistance rpeak 0 ≤ VNO ≤ V+, ICOM = –100 mA, Switch ON, See Figure 12 25°C ON-state resistance ron VNO = 2.
PAGE 4
TS5A23166 SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 www.ti.com Electrical Characteristics for 5-V Supply (1) (continued) V+ = 4.5 V to 5.5 V, TA = –40°C to 85°C (unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS TA V+ MIN 25°C 5V 1 Full 4.5 V to 5.
PAGE 5
TS5A23166 www.ti.com SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 Electrical Characteristics for 3.3-V Supply (1) V+ = 3 V to 3.
PAGE 6
TS5A23166 SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 www.ti.com Electrical Characteristics for 3.3-V Supply (1) (continued) V+ = 3 V to 3.6 V, TA = –40°C to 85°C (unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS TA V+ MIN 25°C 3.3 V 1.5 Full 3 V to 3.6 V 1 25°C 3.3 V 4.5 Full 3 V to 3.
PAGE 7
TS5A23166 www.ti.com SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 Electrical Characteristics for 2.5-V Supply (1) V+ = 2.3 V to 2.7 V, TA = –40°C to 85°C (unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS TA V+ MIN TYP MAX UNIT Analog Switch Analog signal range VCOM, VNO 0 Peak ON resistance rpeak 0 ≤ VNO ≤ V+, ICOM = –8 mA, Switch ON, See Figure 12 25°C ON-state resistance ron VNO = 1.8 V, ICOM = –8 mA, Switch ON, See Figure 12 25°C VNO = 1.8 V, 0.
PAGE 8
TS5A23166 SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 www.ti.com Electrical Characteristics for 2.5-V Supply (1) (continued) V+ = 2.3 V to 2.
PAGE 9
TS5A23166 www.ti.com SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 Electrical Characteristics for 1.8-V Supply (1) V+ = 1.65 V to 1.
PAGE 10
TS5A23166 SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 www.ti.com Electrical Characteristics for 1.8-V Supply (1) (continued) V+ = 1.65 V to 1.95 V, TA = –40°C to 85°C (unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS TA V+ MIN TYP MAX 9 18 UNIT Dynamic 25°C 1.8 V 3 Full 1.65 V to 1.95 V 1 25°C 1.8 V 5 Full 1.65 V to 1.95 V 4 CL = 1 nF, See Figure 20 25°C 1.8 V 2 pC VNO = V+ or GND, Switch OFF, See Figure 15 25°C 1.8 V 19.
PAGE 11
TS5A23166 www.ti.com SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 TYPICAL PERFORMANCE 3.5 3.0 TA = 25_C ron (Ω) 2.5 V+ = 1.8 V 2.0 1.5 V+ = 2.5 V V+ = 3.3 V 1.0 V+ = 5 V 0.5 0.0 0 1 2 3 4 5 6 VCOM (V) Figure 1. ron vs VCOM 1.6 1.4 ron (W) 1.2 855C 1.0 0.8 255C 0.6 –405C 0.4 0.2 0.0 0 1 2 3 4 VCOM (V) Figure 2. ron vs VCOM (V+ = 3.3 V) 1.2 1.0 855C 255C ron (W) 0.8 –405C 0.6 0.4 0.2 0.0 0 1 2 3 4 5 6 VCOM (V) Figure 3.
PAGE 12
TS5A23166 SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 www.ti.com TYPICAL PERFORMANCE (continued) 70 ICOM(OFF) Leakage Current (nA) 60 50 40 INO/NC(OFF) 30 20 INO/NC(ON) 10 ICOM(ON) 0 −40°C 25°C 85°C TA (°C) Figure 4. Leakage Current vs Temperature (V+ = 5.5 V) 20 Charge Injection (pC) 15 10 V+ = 5 V V+ = 3 V 5 0 −5 −10 −15 0 1 2 3 4 5 Bias Voltage (V) Figure 5. Charge Injection (QC) vs VCOM 12 10 tON tON/tOFF (ns) 8 tOFF 6 4 2 0 0 1 2 Figure 6.
PAGE 13
TS5A23166 www.ti.com SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 TYPICAL PERFORMANCE (continued) 10 tOFF 9 tON/tOFF (ns) 8 7 6 tON 5 4 3 2 1 0 -40 °C Figure 7. tON 25°C 85°C TA (°C) and tOFF vs Temperature (V+ = 5 V) 0 −1 Gain (dB) −2 −3 −4 −5 −6 −7 −8 −9 0.1 1 10 100 1000 Frequency (MHz) Figure 8. Bandwidth (V+ = 5 V) 0 Attenuation (dB) −20 −40 −60 −80 −100 −120 0.1 1 10 100 1000 Frequency (MHz) Figure 9.
PAGE 14
TS5A23166 SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 www.ti.com TYPICAL PERFORMANCE (continued) 0.010 0.009 THD + (%) 0.008 0.007 0.006 0.005 0.004 0.003 0.002 0.001 0.000 0 10 100 1000 10000 100000 Frequency (Hz) Figure 10. Total Harmonic Distortion vs Frequency 160 140 I+ (nA) 120 100 80 60 40 20 0 -40 °C 25°C 85°C TA (°C) Figure 11.
PAGE 15
TS5A23166 www.ti.com SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 Table 2. PIN DESCRIPTION PIN NUMBER NAME DESCRIPTION DCU YZT or YZP 1 A1 NO1 2 B1 COM1 3 C1 IN2 4 D1 GND Digital ground 5 D2 NO2 Normally open 6 C2 COM2 7 B2 IN1 Digital control pin to connect COM to NO 8 A2 V+ Power Supply Normally open Common Digital control pin to connect COM to NO Common Table 3.
PAGE 16
TS5A23166 SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 www.ti.com PARAMETER MEASUREMENT INFORMATION V+ VNO NO COM + VCOM Channel ON r on + VI ICOM IN VCOM * VNO W I COM VI = VIH or VIL + GND Figure 12. ON-State Resistance (ron) V+ VNO NO COM + VCOM + VI OFF-State Leakage Current Channel OFF VI = VIH or VIL IN + GND Figure 13.
PAGE 17
TS5A23166 www.ti.com SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 PARAMETER MEASUREMENT INFORMATION (continued) V+ VNO NO Capacitance Meter VBIAS = V+ or GND VI = V+ or GND COM COM VI IN Capacitance is measured at NO, COM, and IN inputs during ON and OFF conditions. VBIAS GND Figure 15.
PAGE 18
TS5A23166 SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 www.ti.com PARAMETER MEASUREMENT INFORMATION (continued) V+ Network Analyzer 50 W VNO NO Channel ON: NO to COM VCOM COM VI = VIH or VIL Source Signal Network Analyzer Setup VI 50 W IN Source Power = 0 dBm (632-mV P-P at 50-W load) + GND DC Bias = 350 mV Figure 17.
PAGE 19
TS5A23166 www.ti.com SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 PARAMETER MEASUREMENT INFORMATION (continued) V+ RGEN VGEN Logic Input (VI) VIH OFF ON OFF V IL NO COM + VCOM ∆VCOM VCOM CL(1) VI VGEN = 0 to V+ IN Logic Input(2) (1) (2) RGEN = 0 CL = 1 nF QC = CL × ∆VCOM VI = VIH or VIL GND CL includes probe and jig capacitance. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns, tf < 5 ns. Figure 20.
PAGE 20
TS5A23166 SCDS196G – MAY 2005 – REVISED FEBRUARY 2013 www.ti.com REVISION HISTORY Changes from Revision F (September 2012) to Revision G • 20 Page Changed pin numbers for YZT/YZP package pinout ............................................................................................................
PAGE 21
PACKAGE OPTION ADDENDUM www.ti.
PAGE 22
PACKAGE OPTION ADDENDUM www.ti.com 18-Oct-2013 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided.
PAGE 23
PACKAGE MATERIALS INFORMATION www.ti.com 17-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) TS5A23166DCUR US8 DCU 8 3000 180.0 8.4 2.25 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.35 1.05 4.0 8.0 Q3 TS5A23166DCUR US8 DCU 8 3000 180.0 9.0 2.05 3.3 1.0 4.0 8.0 Q3 TS5A23166DCURG4 US8 DCU 8 3000 180.0 8.4 2.25 3.35 1.05 4.0 8.
PAGE 24
PACKAGE MATERIALS INFORMATION www.ti.com 17-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TS5A23166DCUR US8 DCU 8 3000 202.0 201.0 28.0 TS5A23166DCUR US8 DCU 8 3000 182.0 182.0 20.0 TS5A23166DCURG4 US8 DCU 8 3000 202.0 201.0 28.0 TS5A23166YZPR DSBGA YZP 8 3000 220.0 220.0 35.0 TS5A23166YZTR DSBGA YZT 8 3000 220.0 220.0 35.
PAGE 25
PAGE 26
PAGE 27
D: Max = 1.918 mm, Min =1.858 mm E: Max = 0.918 mm, Min =0.
PAGE 28
D: Max = 1.918 mm, Min =1.858 mm E: Max = 0.918 mm, Min =0.
PAGE 29
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.