Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - transceivers USB 2.0 1/1 TSSOP 16

TUSB1105, TUSB1106

www.ti.com

SCAS818E –MAY 2006–REVISED SEPTEMBER 2010

ADVANCED UNIVERSAL SERIAL BUS TRANSCEIVERS

Check for Samples: TUSB1105, TUSB1106

FEATURES

• Support I/O Voltage Range From 1.65 V to

3.6 V

• Compatible With Universal Serial Bus

Specification Rev. 2.0 • IEC-61000-4-2 ESD Compliant

• Transmit and Receive Serial Data at Both – ±9-kV Contact-Discharge Model

Full-Speed (12-Mbit/s) and Low-Speed (D+, D–, V

CC(5.0)

)

(1.5-Mbit/s) Data Rates

– ±15-kV Human-Body Model

• Integrated Bypassable 5-V to 3.3-V Voltage (D+, D–, V

CC(5.0)

)

Regulator for Powering Via USB V

BUS

• TUSB1105 Available in Quad Flat No-Lead

• V

BUS

Disconnection Indication Through V

and (QFN) Package; TUSB1106 Available in QFN

and Thin Shrink Small-Outline Package

(TSSOP)

• Used as USB Device Transceiver or USB Host

Transceiver

APPLICATIONS

• Stable RCV Output During SE0 Condition

• Mobile Phones

• Two Single-Ended Receivers With Hysteresis

• Personal Digital Assistants (PDAs)

• Low-Power Operation, Ideal for Portable

• Information Appliances (IAs)

Equipment

• Digital Still Cameras (DSCs)

DESCRIPTION/ORDERING INFORMATION

The TUSB1105 and TUSB1106 universal serial bus (USB) transceivers are compliant with the Universal Serial

Bus Specification Rev. 2.0. These devices can transmit and receive serial data at both full-speed (12-Mbit/s) and

low-speed (1.5-Mbit/s) data rates. The TUSB1105 and TUSB1106 can be used as USB device transceivers or

USB host transceivers.

The devices allow USB application-specific ICs (ASICs) and programmable logic devices (PLDs), with

power-supply voltages from 1.65 V to 3.6 V, to interface with the physical layer (PHY) of the universal serial bus.

They have an integrated 5-V to 3.3-V voltage regulator for direct powering via the USB supply VBUS.

The TUSB1105 allows single-ended and differential input modes selectable by a mode (MODE) input and is

available in RGT and RTZ packages. The TUSB1106 allows only differential input mode and is available in PW,

RGT, RSV, and RTZ packages.

The TUSB1105 and TUSB1106 are ideal for portable electronic devices, such as mobile phones, personal digital

assistants, information appliances, and digital still cameras.

ORDERING INFORMATION

PACKAGE

(1) (2)

ORDERABLE PART NUMBER TOP-SIDE MARKING

TUSB1105RGTR ZYB

QFN – RGT Reel of 3000

TUSB1106RGTR ZYC

TUSB1105RTZR ZYB

–40°C to 85°C QFN – RTZ Reel of 3000

TUSB1106RTZR ZYC

QFN – RSV Reel of 3000 TUSB1106RSVR ZYC

TSSOP – PW Reel of 2000 TUSB1106PWR TU1106

(1) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.

(2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI

website at www.ti.com.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (34 pages)

PAGE 1
TUSB1105, TUSB1106 www.ti.com SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 ADVANCED UNIVERSAL SERIAL BUS TRANSCEIVERS Check for Samples: TUSB1105, TUSB1106 FEATURES • 1 • • • • • • • • Compatible With Universal Serial Bus Specification Rev. 2.0 Transmit and Receive Serial Data at Both Full-Speed (12-Mbit/s) and Low-Speed (1.5-Mbit/s) Data Rates Integrated Bypassable 5-V to 3.
PAGE 2
TUSB1105, TUSB1106 SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 www.ti.com TUSB1105 PACKAGES 4 VP 3 10 D+ RCV 2 11 VPO/VO OE 1 12 VMO/FSE0 16 15 14 13 SO FT CO N V pu(3.3) V C C(5.0) V reg(3.3) GND (expo sed die pad) D− 5 VM 4 VP 3 R CV 2 OE 1 SPE ED SU SPN D 6 7 8 G ND (exposed die pad) 16 15 14 V CC (5.0) VM 9 V CC (I/O ) 8 V pu(3.
PAGE 3
TUSB1105, TUSB1106 www.ti.com SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 FUNCTIONAL BLOCK DIAGRAM 3.3 V VCC(I/O) Voltage Regulator VCC(5.0) Vreg(3.3) Vpu(3.3) SOFTCON 1.5 kΩ(A) OE D+ SPEED VMO/FSE0(B) 33 (1%) D– VPO/VO(B) 33 (1%) MODE(C) + Level Shifter SUSPND RCV – TUSB1105 TUSB1106 VP VM M B L30 1 GND A. Connect to D– for low-speed operation and to D+ for high-speed operation. B. Pin function depends on device type. C. TUSB1105 only Table 1.
PAGE 4
TUSB1105, TUSB1106 SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 www.ti.com Table 1. TERMINAL FUNCTIONS (continued) TERMINAL NAME (1) TUSB1105 PIN NO. RGT GND RTZ Die pad Die pad VCC(I/O) 7 7 TUSB1106 PIN NO. I/O DESCRIPTION PW RTZ 8 6 Ground supply (2) 9 7 Supply voltage for digital I/O pins (1.65 to 3.6 V). When VCC(I/O) is not connected, the D+ and D– pins are in 3-state. This supply pin is independent of VCC(5.0) and Vreg(3.3) and must never exceed the Vreg(3.3) voltage.
PAGE 5
TUSB1105, TUSB1106 www.ti.com SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 FUNCTIONAL DESCRIPTION Function Selection Table 2.
PAGE 6
TUSB1105, TUSB1106 SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 www.ti.com Table 5. Receiving Function (Pin OE = H) DATA STATE RCV VP (1) VM (1) LOW SPEED FULL SPEED Differential logic 0 L L H J K Differential logic 1 H H L K J RCV* (2) L L X X D+, D– SE0 (1) (2) VP = VM = H indicates the sharing mode (VCC(5.0) and Vreg(3.3) are disconnected). RCV* denotes the signal level on output RCV just before SE0 state occurs. This level is stable during the SE0 period.
PAGE 7
TUSB1105, TUSB1106 www.ti.com SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 Power-Supply Input Options The TUSB1105 and TUSB1106 have two power-supply input options. • Internal regulator – VCC(5.0) is connected to 4 V to 5.5 V. The internal regulator is used to supply the internal circuitry with 3.3 V (nominal). Vreg(3.3) becomes a 3.3-V output reference. • Regulator bypass – VCC(5.0) and Vreg(3.3) are connected to the same supply.
PAGE 8
TUSB1105, TUSB1106 SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 www.ti.com Static Electrical Characteristics – Supply Pins over recommended ranges of operating free-air temperature and supply voltage (unless otherwise noted) PARAMETER TEST CONDITIONS MIN Vreg(3.
PAGE 9
TUSB1105, TUSB1106 www.ti.com SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 Static Electrical Characteristics – Digital Pins over recommended ranges of operating free-air temperature and supply voltage (unless otherwise noted) PARAMETER VIL LOW-level input voltage VIH HIGH-level input voltage TEST CONDITIONS 1.65 V to 3.
PAGE 10
TUSB1105, TUSB1106 SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 www.ti.com Static Electrical Characteristics – Analog I/O Pins over recommended ranges of operating free-air temperature and supply voltage, VCC = 4 V to 5.5 V or Vreg(3.3) = 3 V to 3.6 V, VGND = 0 V, TA = –40°C to 85°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VDI Differential input sensitivity |VI(D+) – VI(D–)| 0.2 VCM Differential common-mode voltage Includes VDI range 0.8 2.
PAGE 11
TUSB1105, TUSB1106 www.ti.com SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 Dynamic Electrical Characteristics – Analog I/O Pins (D+, D–) (1) Driver Characteristics, Full-Speed Mode (2) over recommended ranges of operating free-air temperature and supply voltage, VCC = 4 V to 5.5 V or Vreg(3.3) = 3 V to 3.6 V, VCC(I/O) = 1.65 V to 3.
PAGE 12
TUSB1105, TUSB1106 SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 www.ti.com Dynamic Electrical Characteristics for Analog I/O Pins (D+, D–) (1) Receiver Timing, Full-Speed and Low-Speed Mode, Differential Receiver over recommended ranges of operating free-air temperature and supply voltage, VCC = 4 V to 5.5 V or Vreg(3.3) = 3 V to 3.6 V, VCC(I/O) = 1.65 V to 3.
PAGE 13
TUSB1105, TUSB1106 www.ti.com SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 APPLICATION INFORMATION Test Point 33 Ω 500 Ω D.U.T. + 50 pF V – MBL142 Figure 5. Load for Enable and Disable Times A. V = 0 V for tPZH, tPHZ B. V = Vreg(3.3) for tPZL, tPLZ Test Point 25 pF D.U.T. MGS968 Figure 6. Load for VM, VP, and RCV VPU(3.3) 1.5 kΩ D.U.T. D+/D– 33 Ω CL 15 kΩ Test Point Figure 7. Load for D+, D– A. Full-speed mode: connected to D+ B. Low-speed mode: Connected to D– C.
PAGE 14
TUSB1105, TUSB1106 SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 www.ti.com 1.65 V to 3.6 V 3.3 V 0.1 µF GND V V OE CC CC(I/O) V reg(3.3) SPEED 0.1 µF SOFTCON V CC(5.0) SUSPND 1.5 kW V (A) MODE System ASIC V GND pu(3.3) 33 W RCV BUS 0.1 µF GND D+ VMO/FSE0 33 W VPO/VO D– VP TUSB1105/1106 VM GND GND Figure 8. Peripheral-Side (Full-Speed) Regulator Bypass Mode Peripheral-Side (Full-Speed) Regulator Bypass Mode This mode is applicable when there is a 3.
PAGE 15
TUSB1105, TUSB1106 www.ti.com SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 1.65 V to 3.6 V 3.3 V 0.1 µF GND V V OE CC CC(I/O) V reg(3.3) SPEED 0.1 µF SOFTCON V CC(5.0) SUSPND GND 1.5 kW V (A) MODE V pu(3.3) BUS 0.1 µF RCV System ASIC 33 W GND D+ VMO/FSE0 33 W VPO/VO D– VP TUSB1105/1106 VM GND GND Figure 9. Peripheral-Side (Low-Speed) Regulator Bypass Mode Peripheral-Side (Low-Speed) Regulator Bypass Mode This mode is applicable when there is a 3.
PAGE 16
TUSB1105, TUSB1106 SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 www.ti.com 1.65 V to 3.6 V 0.1 µF GND V V OE CC CC(I/O) V reg(3.3) SPEED 0.1 µF SOFTCON V CC(5.0) SUSPND GND 1.5 kW (A) MODE System ASIC V V 0.1 µF BUS PU(3.3) RCV 33 W VMO/FSE0 D+ VPO/VO D– GND 33 W VP TUSB1105/1106 VM GND GND Figure 10. Peripheral-Side (Full-Speed) Internal Regulator Mode A.
PAGE 17
TUSB1105, TUSB1106 www.ti.com SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 1.65 V to 3.6 V 0.1 µF GND V V OE CC CC(I/O) V reg(3.3) 0.1 µF SPEED SOFTCON GND V CC(5.0) SUSPND 1.5 kW (A) MODE V V BUS PU(3.3) RCV System ASIC 0.1 µF 33 W GND D+ VMO/FSE0 33 W D– VPO/VO VP TUSB1105/1106 VM GND GND Figure 11. Peripheral-Side (Low-Speed) Internal Regulator Mode A.
PAGE 18
TUSB1105, TUSB1106 SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 www.ti.com 1.65 V to 3.6 V 0.1 µF GND V CC(I/O) 5V 5V 0.1 µF V reg(3.3) SOFTCON CC(5.0) SUSPND 0.1 µF V CC SPEED GND V V OE V BUS pu(3.3) MODE GND 33 W (A) RCV D+ System ASIC VMO/FSE0 33 W D– VPO/VO 15 kW VP 15 kW TUSB1105/1106 VM GND GND GND GND Figure 12. Host Side (VCC(5.0) Supplied From VBUS Pin) Host Side (VCC(5.0) Supplied From VBUS Pin) If there is no 3.
PAGE 19
TUSB1105, TUSB1106 www.ti.com SCAS818E – MAY 2006 – REVISED SEPTEMBER 2010 1.65 V to 3.6 V 0.1 µF 3.3 V GND V CC(I/O) OE V CC 5V V reg(3.3) SPEED 0.1 µF SOFTCON V CC(5.0) SUSPND GND V BUS V pu(3.3) (A) MODE 33 W RCV D+ System ASIC VMO/FSE0 33 W D– VPO/VO 15 kW VP 15 kW TUSB1105/1106 VM GND GND GND GND Figure 13. Host-Side (3.3-V Supply Present) Internal Regulator Bypass Mode Host-Side (3.3-V Supply Present) Internal Regulator Bypass Mode If a 3.
PAGE 20
PACKAGE OPTION ADDENDUM www.ti.
PAGE 21
PACKAGE OPTION ADDENDUM www.ti.com 20-May-2013 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
PAGE 22
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TUSB1105RGTR Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant QFN RGT 16 3000 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TUSB1105RTZR WQFN RTZ 16 3000 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TUSB1106PWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.
PAGE 23
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TUSB1105RGTR QFN RGT 16 3000 346.0 346.0 35.0 TUSB1105RTZR WQFN RTZ 16 3000 346.0 346.0 35.0 TUSB1106PWR TSSOP PW 16 2000 367.0 367.0 35.0 TUSB1106RGTR QFN RGT 16 3000 346.0 346.0 35.0 TUSB1106RSVR UQFN RSV 16 3000 203.0 203.0 35.0 TUSB1106RTZR WQFN RTZ 16 3000 346.0 346.0 35.
PAGE 24
PAGE 25
PAGE 26
PAGE 27
PAGE 28
PAGE 29
PAGE 30
PAGE 31
PAGE 32
PAGE 33
PAGE 34
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.