Quick Start Guide

Waste Electrical and Electronic Equipment (WEEE)
This symbol means that according to local laws and regulations your product and/or its battery shall
be disposed of separately from household waste. When this product reaches its end of life, take it to a
collection point designated by local authorities. Proper recycling of your product will protect human health
and the environment.
Safety and Regulatory Information
Train Control Systems Inc.
845 Blooming Glen Rd, Blooming Glen, PA 18911 USA
https://tcsdcc.com/contact
Model: UWT-100
FCC ID: 2AUJ6-UWT100
IC: 25442-UWT100
CAN ICES-3(B)/NMB-3(B)
SAR (CE/AU/NZ): Measured Value: 0.204 W/kg (Limit 2.0 W/kg)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
FCC 15.21 Changes or modi cations not expressly approved by the party responsible for compliance could void the user‘s authority to operate
the equipment.
FCC 15.105 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
ISED warning RSS-Gen 8.4
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.”
European Users
• Hereby, Train Control Systems Inc. declares that the radio equipment type UWT-100
(WiFi) is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet ad-
dress: https://tcsdcc.com/DoC
• RF Exposure Information (SAR)
This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. Speci c Absorption Rate (SAR) refers to the rate
at which the body absorbs RF energy. SAR limits are 1.6 Watts per kilogram (over a volume containing a mass of 1 gram of tissue) in countries
that follow the United States FCC limit and 2.0 W/kg (averaged over 10 grams of tissue) in countries that follow the Council of the European
Union limit. Tests for SAR are conducted using standard operating positions with the device transmitting at its highest certi ed power level in all
tested frequency bands. To reduce exposure to RF energy, use a hands-free accessory or other similar option to keep this device away from
your head and body. Carry this device at least 5 mm away from your body to ensure exposure levels remain at or below the as-tested levels.
Choose the belt clips, holsters, or other similar body-worn accessories which do not contain metallic components to support operation in this
manner. Cases with metal parts may change the RF performance of the device, including its compliance with RF exposure guidelines, in a
manner that has not been tested or certi ed, and use such accessories should be avoided.
• Caution: risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Train Control Systems Inc. EU Support Contact Information:
PO Box 17749, BROMSGROVE, B60 9NJ, UNITED KINGDOM
To access the certi cation and compliance details of your UWT-100 follow the steps below
1) Power on the UWT-100 by pressing button 2 until the screen lights up and then pressing button 2 again.
2) Press the Menu ( ) button, scroll to [Settings], and press Enter ( )
3) Scroll to [Regulatory] from the [Settings] menu, and press Enter ( ).
You can now read and review the e-labelling details of your UWT-100
E-Labelling, Compliance and Certi cation