Instructions

ManualsBrandsTFA Dostmann ManualsTesting & Power SupplyTFA Dostmann Maxim II Wireless thermo-hygrometer Black

WIRELESS 868 MHz THERMO-HYGRO-STATION

Instruction Manual

Cat. No. 30.3013.IT

Thank you for choosing this wireless thermo-hygro-station from TFA.

BEFORE YOU USE IT

Please be sure to read the instruction manual carefully.

This information will help you to familiarise yourself with your new device,

learn all of its functions and parts, find out important details about its first

use and how to operate it, and get advice in the event of faults.

Following the instruction manual for use will prevent damage to the

device and loss of your statutory rights arising from defects due to

incorrect use.

We shall not be liable for any damage occurring as a result of not

following these instructions.

Please take particular note of the safety advice!

Please look after this manual for future reference.

SCOPE OF SUPPLY:

•

Thermo-hygro-station (basic unit)

•

Outdoor transmitter

•

Batteries 5 x AA, IEC LR6, 1.5V

•

Instruction manual

FIELD OF OPERATION AND ALL OF THE BENEFITS OF

YOUR NEW THERMO-HYGRO-STATION AT A GLANCE:

•

DCF Radio controlled time with manual setting option

•

Time reception ON/OFF setting

•

12/24 hour display

•

Hour and minute display, seconds indicated by flashing dot

•

Time zone option ±12 hours

•

Date with month calendar display

•

Temperature display in degrees Celsius (°C) or Fahrenheit (°F)

selectable

•

Indoor and outdoor temperature display with MIN/MAX recording

•

Indoor and outdoor humidity display as RH% with MIN/MAX

recording

•

Indoor comfort level indicator- happy or sad face icons

Summary of content (19 pages)

PAGE 1
WIRELESS 868 MHz THERMO-HYGRO-STATION Instruction Manual Cat. No. 30.3013.IT Thank you for choosing this wireless thermo-hygro-station from TFA. BEFORE YOU USE IT Please be sure to read the instruction manual carefully. This information will help you to familiarise yourself with your new device, learn all of its functions and parts, find out important details about its first use and how to operate it, and get advice in the event of faults.
PAGE 2
• • • • • • MIN/MAX recordings for indoor and outdoor temperature show date and time received and can be reset Can receive up to three outdoor transmitters Wireless transmission at 868 MHz Signal reception intervals at 4 seconds Table standing or wall mounting Low battery indicator FOR YOUR SAFETY: • • • The product is exclusively intended for the field of application described above. The product should only be used as described within these instructions.
PAGE 3
ELEMENTS The thermo-hygro-station LCD Display Hanging Hole Battery cover Function Keys The thermo-hygro transmitter • • • • Remote transmission of outdoor temperature and humidity to thermo-hygro-station by 868MHz Shower proof casing Wall mounting case Mounting at a sheltered place. Avoid direct rain and sunshine TO INSTALL AND REPLACE BATTERIES IN THE THERMOHYGRO TRANSMITTER The outdoor thermo-hygro transmitter uses 2 x AA IEC LR6, 1.5V batteries.
PAGE 4
HOW TO INSTALL AND REPLACE BATTERIES IN THE THERMO-HYGRO-STATION The thermo-hygro-station uses 3 x AA, IEC LR6, 1.5V batteries. To install and replace the batteries, please follow the steps below: 1. Insert finger or other solid object in the space at the top center of the battery compartment and lift up to remove the cover. 2. Insert batteries observing the correct polarity (see marking). 3. Replace compartment cover.
PAGE 5
3. 4. before reinserting them. Once the indoor data is displayed user may proceed to the next step. After the batteries are inserted, the thermo-hygro-station will start receiving data signal from the transmitter. The outdoor temperature and humidity data should then be displayed on the thermo-hygrostation. If this does not happen after 2 minutes, the batteries will need to be removed from both units and reset from step 1.
PAGE 6
7. 8. hygro-station. If this does not happen after 2 minutes, the batteries will need to be removed from all the units and reset from step 1. Insert the batteries in the third transmitter as soon as the "channel 2" icon and outdoor data are displayed on the thermo-hygro-station. Then within 2 minutes, the channel 3 outdoor data from the third transmitter will be displayed and the channel icon will shift back to "1" once the third transmitter is successfully received.
PAGE 7
Once the outdoor data reception test period is completed, the DCF tower icon in the clock display will start flashing in the upper left corner. This indicates that the clock has detected that there is a radio signal present and is trying to receive it. When the time code is received, the DCF tower becomes permanently lit and the time will be displayed.
PAGE 8
• Note: in 24hr time display mode, the day is set by using the IN key.
PAGE 9
* When the signal is successfully received by the thermo-hygro-station, the outdoor transmission icon will be switched on. (If not successful, the icon will not be shown on LCD). The user can then easily see whether the last reception was successful (icon on) or not (icon off). On the other hand, the short blinking of the icon shows that a reception is currently taking place.
PAGE 10
1. 2. 3. Press the SET key after completing the contrast setting in order to enter the Time Zone setting (flashing). Using the IN key, set the time zone. The range runs from -/+ 12 and then runs from -12 back to +12 in consecutive 1-hour intervals. Press the SET again to confirm and to enter the “Time reception ON/OFF setting” or exit the setting mode by pressing the CHANNEL key.
PAGE 11
Note: When 24h mode display is selected, the calendar format will be date and month display. When 12h mode display is selected, the calendar format will be month and date display. MANUAL TIME SETTING: In case the thermo-hygro-station is unable to detect the DCF-signal (disturbances, transmitting distance, etc.), the time can be manually set. The clock will then work like a normal Quartz clock. Hours (flashing) 1. 2. 3. Minutes (flashing) Press the SET key until the time display flashes.
PAGE 12
1. 2. 3. 4. Press the SET key after entering the manual time setting in order to enter the year setting (flashing). Reset the year by pressing the IN key. The range runs from 2006 to 2039. Press the SET key again to enter the month and date display (flashing). Using the OUT key, set the month required. Using the IN key, set the date required. Press the SET again to confirm and to enter the “Snooze setting” or exit the setting mode by pressing the CHANNEL key.
PAGE 13
INDOOR RELATIVE HUMIDITY AND INDOOR TEMPERATURE: The indoor temperature and humidity are automatically detected and displayed on the second section of the LCD. Indoor comfort indicator MIN display Indoor temperature in °C/ºF Indoor relative humidity % THE COMFORT LEVEL INDICATORS: Comfortable: Uncomfortable: A happy face icon “☺” indicating a temperature level between 20.0°C and 25.9°C and humidity between 45% and 65%. A sad face icon “ ” indicating any value outside the comfortable range.
PAGE 14
OUTDOOR TEMPERATURE/HUMIDITY DATA: The last LCD section shows the outdoor temperature and humidity, the reception indicator, the transmitter identification number and the MIN/MAX outdoor data. Number showing the transmitter unit (only if there is more than one transmitter) Outdoor Transmission Signal MAX display Relative humidity % Outdoor temperature in °C/ºF TOGGLING AND RESETTING THE OUTDOOR RECORDINGS: 1. 2.
PAGE 15
2. Use OUT key to view the MIN/MAX temperature and humidity data for the selected transmitter. Note: the MIN/MAX data for each transmitter needs to be reset separately. ABOUT THE OUTDOOR TRANSMITTER The range of the thermo-hygro transmitter may be affected by the temperature. At cold temperatures the transmitting distance may be decreased. Please bear this in mind when positioning the transmitters. Also the batteries may be reduced in power for the thermo-hygro transmitter.
PAGE 16
POSITIONING THE THERMO-HYGRO-STATION The thermo-hygro-station provides the option of table standing or wall mounting the unit. Before wall mounting, please check that the outdoor data can be received from the desired locations. To wall mount: 1. Fix a screw (not supplied) into the desired wall, leaving the head extended out by about 5mm. 2. Place the thermo-hygro-station onto the screw, using the hanging hole on the backside. Gently pull the thermo-hygro-station down to lock the screw into place.
PAGE 17
• Remove the batteries if you do not use the product for a lengthy period.
PAGE 18
Cd=cadmium, Hg=mercury, Pb=lead This instrument is labelled in accordance with the EU Waste Electrical and Electronic Equipment Directive (WEEE). Please do not dispose of this product with other household waste. The user is obligated to take end-of-life devices to a designated collection point for the disposal of electrical and electronic equipment, in order to ensure environmentallycompatible disposal.
PAGE 19
TFA Dostmann GmbH & Co. KG, Zum Ottersberg 12, D - 97877 Wertheim No part of this manual may be reproduced without written consent of TFA Dostmann. The technical data are correct at the time of going to print and may change without prior notice. DECLARATION OF CONFORMITY Herewith we declare, that this wireless transmission device does comply with the essentials requirements of R&TTE Directive 1999/5/EC. A copy of the signed and dated Declaration of Conformity is available on request via info@tfa-dostmann.