Feuchtemessgerät Bedienungsanleitung
Durch das kapazitive Messverfahren lässt sich die Feuchtigkeit in Beton, Holz, Estrich und vieler weiterer Baustoffe ohne Beschädigung oder Zerstörung messen. Technische Merkmale Zeigt den Feuchtigkeitsgehalt der Materialien schnell an Eindringtiefe ca. 20-40mm.
Beschreibung der Frontseite ① ③ ② ④ ⑤ ⑥ ⑦ ③ ④
Sensor/Messkugel ②MAX-/MIN-Taste ③LCD-Anzeige ④Einschalt-/Ausschalttaste ⑤Hintergrundbeleuchtungstaste ⑥MEAS-Taste ⑦Batteriedeckel Tastenfunktion Ein-/Aus-Taste Schaltet das Messgerät ein oder aus. MEAS-Taste Das Gerät beginnt mit dem Messen nach Drücken der MEAS-Taste. Wenn Sie die Taste loslassen, erscheint das Anzeigesymbol “HOLD” auf dem LCD-Display und zeigt somit an, dass der aktuelle Messwert festgehalten wird.
Sie die MAX-/MIN-Taste und das ‘MAX’-Symbol erscheint auf dem LCD-Display. Das Messgerät beginnt den MAX-Wert zu messen. Drücken Sie erneut die Taste, das ‘MIN’-Symbol erscheint auf dem LCD-Display und das Messgerät beginnt den MIN-Wert zu messen. Drücken Sie zwei Sekunden lang die MAX-/MIN-Taste, um diesen Modus zu verlassen. Hintergrundbeleuchtungstaste Schaltet die Hintergrundbeleuchtung ein oder aus. Gebrauch Halten Sie das Gerät so, dass Ihre Hände nicht in der Nähe der runden Messsonde sind.
Sobald Metall in Baustoffen vorhanden ist, kann es zu Fehlmessungen kommen. Nachfolgende Informationen denen als Hinweis. Das Instrument ist ein Indikator zur schnellen Messung. Baustoffe: Gips Zement 0..35 36..60 61..100 0..25 26..50 51..75 Über 75 trocken halbtrocken feucht trocken halbtrocken feucht nass Batteriewechsel Wenn das SymboI “ ” auf der LCD-Anzeige erscheint, wechseln Sie bitte die Batterie. Öffnen Sie das Batteriefach und ersetzen Sie die leere Batterie durch eine neue.
Moisture Meter Instruction Manual
The NON-Contact Moisture Meter is an electronic dampness indicator with a measuring process working on the principle of high frequency measurement. The instrument is used for non-destructively tracing dampness in building materials of all kinds as well as for detecting damp distribution in walls, ceilings and floors. It is particularly suitable for pre-testing the readiness of building materials for covering prior to CM measurement.
Specification Specifications: Sensor Type : Max Resolution: metal spheroid 0 to 100 1 Battery : 9V battery Dimensions : Weight: 180 mm×45mm×35mm 180g Measuring Range: Adjustment The instrument is calibrated fully electronically and readjustment is not necessary. Safety remarks These is a risk of injury if the metal ball comes into contact with live parts. Do not use the instrument in the immediate vicinity of older equipment or equipment equally sensitive to high frequencies (e.g.
the “MESA” button and hold the instrument with the ball in the air. The displayed value must be between -5 and +5.
Metal Ball ② MAX/MIN Button ③LCD Display ④Power ON/OFF Button ⑤Backlight Button ⑥MEAS Button ⑦Battery Cover Button Function Power Button Turn the meter power ON or OFF. MEAS Button Press the MEAS button, the instrument will start measuring. Release this button the “HOLD” icon will appear on the LCD indicating that the current reading is being held.
meter will begin keeping track of MAX value. Press the button again, ‘MIN’ icon will appear on LCD display and the meter will begin keeping track of MIN value. Press MAX/MIN button for two seconds to exit this mode. Backlight button Turn the backlight on or off. Operation Hold the instrument as near to the back as possible. Press the “MEAS” button and use the ball to scan the surface under investigation. The ball must be in firm contact with the material.
coverings, the display jumps to ca. 50 digits for otherwise dry surroundings. It is only possible to reach a conclusion about the absolute dampness in wt-% or the dampness in CM-% if the normal drying out process has taken place(e.g not during or shortly after the use of drying agents or heat guns). If there is not a roughly normal variation in dampness between the surface and the interior ,too low a measured value may be indicated. The raw density of the material being measured has a noticeable affect.
The manufacturer of the instrument can thus not give any guarantee for the correctness of this information.The conclusions to be drawn from the result of measurements by each user depend upon the individual circumstances and his experience gained from professional practice. Construction material: Gypsum 0..35 dry 36..60 half-dry 61..100 wet Cement 0..25 dry 26..50 half-dry 51..