WIRELESS 868 MHz WEATHER STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this Weather Station with wireless 868 MHz transmission of outdoor temperature and display of indoor temperature, weather forecast icons and weather tendency indicators. It is further featuring a DCF-77 radio controlled clock and alarm function. With four easy to use function keys, this innovative product is ideal for use in the home or office.
• • • • • • • • • • • 24 hour display Alarm function with snooze Time zone +/- 12 hours Temperature display in degree Celsius (°C) Indoor and outdor temperature with MIN/MAX records Manual reset of MIN/MAX records 3 weather forecast with weather tendency indicator Wireless transmission at 868 MHz Signal reception intervals at 4 seconds Low battery indicator Wall mounting or table standing (foldout stand) The Outdoor Temperature Transmitter • Remote transmission of outdoor temperature to Weather station by
. 4. 5. seconds, remove the batteries and wait for at least 30 seconds before reinserting them. After inserting the batteries, the Weather station will start receiving data from the transmitter. The outdoor temperature and the signal reception icon should then be displayed on the Weather station. If this does not happen after 3 minutes, the batteries will need to be removed from both units and reset from step 1.
1. 2. 3. Lift up the battery compartment cover. Insert batteries observing the correct polarity (see marking). Replace compartment cover. HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER The Temperature Transmitter uses 2 x AA, IEC LR6, 1.5V battery. To install and replace the batteries, please follow the steps below: 1. Remove the battery compartment cover at the back of the transmitter. 2. Insert the batteries, observing the correct polarity (see marking). 3.
Please participate in the preservation of the environment. Return used batteries to an authorised depot. FUNCTION KEYS: Weather station: The weather station has four easy to use function keys.
• Exit manual setting modes LCD SCREEN AND SETTINGS: Radio controlled time reception icon Alarm icon Time Weather forecast icon Weather tendency indicator Low battery indicator (transmitter) Outdoor Reception Signal icon* Outdoor Temperature in °C Low battery indicator (weather station) Indoor Temperature in °C MIN/MAX indoor temperature MIN/MAX outdoor temperature * When the outdoor signal is successfully received by the Weather Station, this icon will be switched on.
Section 2 - WEATHER FORECAST AND WEATHER TENDENCY ICONS • Display of the weather to be expected in form of three weather symbols and two weather tendency indicators in form of an arrow, which change their appearance depending on the air pressure development Section 3 – INDOOR AND OUTDOOR TEMPERATURE • Display the current indoor temperature and indoor MIN/MAX records • Display of low battery indicator (weather station) • Display the current outdoor temperature and outdoor MIN/MAX records • A signal reception
3. -12, 12, 11, 10… 2, 1, 0, in consecutive 1-hour intervals. Confirm with the SET key and enter the Time reception On/Off setting. TIME RECEPTION ON/OFF SETTING flashing In area where reception of the radio-controlled time (DCF time) is not possible, the time reception function can be turned OFF. The clock will then work as a normal Quartz clock. (Default setting is ON). 1. The digit “ON” digit will start flashing on the LCD. 2. Use the + key to turn OFF the time reception function if necessary. 3.
3. 4. The minute will be flashing. Press the + key to just the minutes. Confirm with the SET key and exit the setting mode. Note : The unit will still try to receive the signal despite a manual setting. When the signal is received, the manually set time will automatically be replaced by the received time. During reception attempts, the DCF tower icon will flash. If reception has been unsuccessful, the DCF tower icon will not appear but reception will still be attempted.
2. To stop the alarm completely, press any keys other than the MIN/MAX RESET key. WEATHER FORECAST AND TENDENCY THE WEATHER FORECASTING ICONS : There are 3 weather icons in the second section of LCD which can be displayed in any of the following combinations : Sunny Cloudy with sunny intervals Rainy For every sudden or significant change in the air pressure, the weather icons will update accordingly to represent the change in weather.
Station to collect air pressure data at a constant altitude and therefore result in a more accurate forecast. Common to weather forecasting, absolute accuracy cannot be guaranteed. The weather forecasting feature is estimated to have an accuracy level of about 75% due to the varying areas the Weather Station has been designed for use in.
Note : Once the weather tendency indicator has registered a change in the air pressure, it will remain permanently visualized on the LCD. INDOOR TEMPERATURE AND MIN/MAX RECORDS The indoor temperature and indoor MIN/MAX records are displayed on the last section of the LCD. Indoor icon Indoor Temperature MIN record MAX record Note: The MIN/MAX indoor temperature range is -9ºC to + 38ºC with 1°C resolution.
1. In normal display mode, press and hold the MIN/MAX RESET key for 3 seconds. This will reset the indoor and outdoor MIN/MAX temperatures. LOW BATTERY INDICATOR Low battery indicator is displayed on the LCD when the batteries require changing. 868 MHz RECEPTION CHECK The Weather station should receive the temperature data within 3 minutes after set-up.
be reset (see Setting up). POSITIONING THE WEATHER STATION: The Weather Station may be hung onto wall easily or free standing. To wall mount Choose a sheltered place. Avoid direct rain and sunshine. Before wall mounting, please check that the outdoor temperature values can be received from the desired locations. Wall mounting 1. Fix a screw (not supplied) into the desired wall, leaving the head extended out by about 5mm. 2.
POSITIONING THE TEMPERATURE TRANSMITTER: The Transmitter is supplied with a holder that may be attached to a wall with the two screws supplied. The Transmitter can also be position on a flat surface by securing the stand to the bottom to the Transmitter. To wall mount: 1. Secure the bracket onto a desired wall using the screws and plastic anchors. 2. Clip the remote temperature sensor onto the bracket.
• • • • • • • Immediately remove all low powered batteries to avoid leakage and damage. Replace only with new batteries of the recommended type. When cleaning the display and casings, use a soft damp cloth only. Do not use solvents or scouring agents as they may mark the LCD and casings. Do not submerge the unit in water. Special care shall be taken when handling a damaged LCD display. The liquid crystals can be harmful to user's health. Do not make any repair attempts to the unit.
Dimensions (L x W x H) : Weather station : Temperature transmitter : 118.4 x 28 x 137.4mm 38.2 x 21.2 x 128.3 mm LIABILITY DISCLAIMER: • The electrical and electronic wastes contain hazardous substances. Disposal of electronic waste in wild country and/or in unauthorized grounds strongly damages the environment. • Please contact your local or/and regional authorities to retrieve the addresses of legal dumping grounds with selective collection. • All electronic instruments must from now on be recycled.