GUIDE Cat. No. 42.7003 Instruction Manual INTRODUCTION This device is a digital product that provides altimeter, barometer, compass, altimeter data, dual time, chronograph, chronograph data and alarm functions. Features: Altimeter - 1 meter (or foot) resolution and with working range from -700 meters (-2296 feet) to 9000 meters (29520 feet). - Graphical expression of changes provided. - Unit in meters or feet selectable. - 20 memories with date, time and altitude reading.
Chronograph - 1/100-second resolution with working range up to 24 hours. - 100 memories for lap/split times stored in a maximum of 30 runs. Alarm - 2 daily alarms. - Hourly chime. Electro-luminescent backlight - 3 seconds light up EL backlight. Altimetermode with altitude change: measures every 2,5 seconds Altimetermode without altitude change (barometer mode): every 2,5 minutes Barometermode: measures every 2,5 minutes. Changes to Time mode after 24 hours Temperature: measures every 2,5 minutes.
BASIC OPERATION OF BUTTONS A: - SWITCH AMONG DISPLAYS - TAKE BEARING - STORE ALTITUDE DATA (PRESS AND HOLD) - FORWARD SELECTION OF ALTITUDE DATA - START/LAP OF CHRONOGRAPH - RETRIEVE DATA IN RUN - TURN ALARM ON AND OFF - FORWARD SETTING (SET OR CALIBRATION) B: - SWITCH BETWEEN NORMAL TIME AND DUAL TIME (PRESS AND HOLD) - SWITCH BETWEEN UNITS OF TEMPERATURE (PRESS AND HOLD) - SWITCH BETWEEN UNITS OF ALTITUDE (PRESS AND HOLD) - REVERSE SELECTION OF ALTITUDE DATA - STOP CHRONOGRAPH - STORE CHRONOGRAPH DATA (P
MODE CHANGE OPERATION There are 9 modes: Normal Time, Dual Time, Compass, Barometer, Altimeter, Altimeter Data, Chronograph, Chronograph Data and Alarm. Press C to change from mode to mode, hold down B to switch between Normal Time mode and Dual Time mode as in the following: NORMAL TIME Hold B DUAL TIME C COMPASS C BAROMETER C ALTIMETE C C ALTIMETER DATA C CHRONOGRAPH C CHRONOGRAPH DATA C ALARM * At any mode, holding down C will change to Time mode directly.
TIME MODE Hold B Use C to enter Time mode. * Mode prompt “TIME” is displayed first. - There are 2 time modes, Normal Time (indicated by T1) and Dual Time ( indicated by T2), and they count up individually with the same second. - There are 3 displays for time. They are Time, Time with Barometer and Time with Weather. - There is an auto-calendar from 2000 to 2049.
2. Use A (+) and B (-) to change the setting. Holding down either button scrolls the setting at high speed. 3. Press C to advance to the next setting as in the following: C C C HOUR MINUTE SECOND YEAR C C 12/24H C DAY C MONTH * When second digits are flashing, press A or B to reset the digits to 00. Resetting seconds when the digi ts are between 00 to 29 will leave the minute digits unchanged, or between 30 to 59 will increase the minute digits by one.
2. Rotate the product clockwise slowly for 2 complete rotations * Each rotation must last for at least 15 seconds. Keep the watch in a level position when calibrating. Do avoid close contact to metal parts or other electrical instruments, when calibrating. 3. Press D and the ten-degree digit starts to flash on the display, which indicates the declination angle setting screen. * Press A will end calibration skipping the declination angle setting. In this case, the declination angle is set to 0 degree. 4.
BAROMETER MODE Barometer mode indicator Use C to enter Barometer mode. * Mode prompt “BARO” is displayed first. - Barometer mode indicator is shown. - The barometer is of 1 hPa resolution and with work ing range from 300 hpa to 1100 hpa. - Both sea level pressure and absolute pressure can be shown. - Graph showing the changes in sea level pressure is provided. * Graph will be cleared only after battery replacement or reset.
To switch between °F and °C 1. Use A or E to switch to the barometer display with temperature. 2. Hold down B until the unit indicator (°F or °C) stops flashi ng to switch temperature between °F and °C. To set sea level pressure reading 1. Hold down D until “SET CURRENT WEATHER” scrolls on the display, which indicates the weather setting screen. * The weather indicators start to flash. 2. Press C, “SET SEA LEVEL PRESSURE” scrolls on the display, which indicates reading setting screen.
ALTIMETER MODE Use C to enter Altimeter mode. * Mode prompt “ALTI” is displayed first. - Altimeter mode indicator is shown. - The altimeter is of 1 meter (or foot) resolution an d with working range from -700 meters (-2296 feet) to 9000 meters (29520 feet). - Altitude reading in meters or feet selectable. - Graph showing the changes in altitude is provided. * Graph will be cleared only after battery replacement or reset. - Maximum 20 altitude data can be stored.
ALTIMETER DATA MODE 3 seconds or E Use C to enter Altimeter Data mode. * Mode prompt “ALTI DATA” is displayed first. - Data number, time, date and altitude reading can be retrieved. * Altitude data are shown in 2 different displays. To retrieve the altitude data 1. Use A (+) and B (-) to select the altitude data to be retrieved. 2. Press E to switch between the 2 displays of data. * If no button is pressed, the 2 displays will be shown for 3 seconds alternately.
seconds, then the display will show the current running ti mes automatically. To measure elapsed time 1. Press A to start the chronograph. 2. Press B to stop the chronograph. * You can resume the measurement operation by pressing A. 3. Hold down B until the next run number is shown on the display. * Data of the current run is stored and chronograph is reset to all zeros. To measure lap/split times 1. Press A to start a time measurement. 2. Press A again when you want to take the first lap/split time. 3.
* Returns to chronograph display automatically after 3 seconds or when any button is pressed. E 3 segundos o pulsando cualquier botón MODO DATOS DE CRONÓGRAFO 2 second Use C to enter Chronograph Data mode. * Mode prompt “CHRO DATA” is displayed first. - Run number, date, lap/split time of each lap, best lap time and average lap time can be retrieved. - If chronograph is running, chronograph data cannot be cleared. To retrieve the chronograph data 1. Use B to select the run to be retrieved.
To clear all runs Hold down D until “----” is shown on the display. * All runs are cleared. ALARM MODE Use C to enter Alarm mode. * Mode prompt “ALRM” is displayed first. - There are 2 daily alarms and they can be set to refer to Normal Time (indicated by T1) or Dual Time (indicated by T2). - Daily alarm sounds at the same time each day, while it is turned on. - The alarm sounds at the preset time for about 20 seconds, or until y ou stop it by pressing any button.
To turn the alarm on and off Press A to turn the alarm on (indicated by ON) and off (indicated by OFF). * If the alarm is turned on, the alarm on indicator will be shown. RESETTING THE PRODUCT Hold down A, B, C and D simultaneously, all segments will be “on”, then release the buttons and the product will be reset. * After reset, there will not be any measurement of altitude, pressure or temperature until A, C or E is pressed . * After reset, entering Compass mode will change to calibration screen directly.