Bump Device Manual
Contents A - Introduction 3 A.1. Intention of Use 3 A.2. Device Technical Specification 4 A.2.1. Physical Parameters 4 A.2.2. Electrical Parameters 4 A.2.3. Environmental Parameters 4 A.2.4. Frequencies and Data Transmission 4 A.3. Safety Warnings 5 A.4. Warranty Statement 7 B - Getting Started 8 B.1. Bump Package 8 B.2. Bump Device Features 8 B.3. Charging 9 B.4. Approvals – Safety and Electromagnetic Compatibility C - Set up and Operation 10 11 C.1. Link a Bump Device 11 C.
A - Introduction A.1. Intention of Use WARNING: The Bump Device and associated equipment are to promote safe behaviour only. They CAN NOT and WILL NOT prevent the wearer / user from contracting or passing on COVID-19 or other such airborne germs and viruses. The Bump Device is designed to work exclusively with the Tharsus Bump Hub. The Tharsus Bump Device is a wearable device which promotes social distancing. Warnings are generated as wearers approach one another.
A.2. Device Technical Specification A.2.1. Physical Parameters Depth 20mm / 0.8’ Diameter, including soft case 70mm / 2.75’ Weight, device + lanyard 38g + 60g / 1.27oz + 2.1oz A.2.2. Electrical Parameters Charging Voltage (VDC) 5.0V, via USB, micro-B Battery Type Li – Polymer Voltage 3.7V Nominal Power (mAh) 280 Charging Lead Length 1m/ 3.3ft A.2.
A.3. Safety Warnings Do not operate this equipment until the safety information and instructions in this user manual have been read and understood by all personnel concerned. WARNING: The Bump Device contains an emitter which transmits RF signals when it is powered. There is potential for radio interference when it is near televisions, radios, computers, or other electronic devices.
FCC SPECIFIC WARNING - changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. correct the interference by one or more of the following measures: FCC SPECIFIC WARNING - The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure condition without restriction. —Increase the separation between the equipment and receiver.
A.4. Warranty Statement This warranty applies to the Bump Device as manufactured and supplied by Tharsus. Should the equipment be defective as to materials or workmanship, the company warrants that it will remedy such defects. The warranty period will be 12 months from date of commissioning or 18 months from date of manufacture, whichever comes first.
B – Getting Started B.1. Bump Package The device will be supplied assembled with the necessary firmware already preinstalled and configured for use. Contents should include: Bump Device x1 USB Charging lead x1 Quick start guide x1 Lanyard x1 Lanyard Union x2 Please report any missing or damaged items immediately. Do not use the equipment if it is damaged or incomplete. B.2.
B.3. Charging WARNING: Don’t let your battery completely drain. Do not leave a Lithium Ion Polymer battery on prolonged charge when not in use. When possible, charge your device in small amounts to keep the battery from depleting. With the device not being worn, the charging cable supplied can be connected and the device charged as shown in Figure 2.
B.4. Approvals – Safety and Electromagnetic Compatibility Safety - only relevant to the Bump model BS EN IEC 62368-1:2014+A11:2017 Audio/video, information and communication technology equipment. Safety requirements Bluetooth Radio is tested to: EN 300 328 V2.2.2 UWB radio is tested to: EN 302 065-2 V2.1.1 EMC: EN 301 489-17 Waste Electrical and Electronic Equipment Directive (WEEE Directive) 2012/19/EU - Only relevant to the Bump model Do not dispose of the Bump Device in domestic waste.
C. Set up and operation C.1. Register your Bump You will need email access and a Bump device. Your Bump admin will provide you with a Bump pack and send you an email with your ‘My Bump’ sign up link. Once you’ve received your pack, go to the registration link, enter your personal details, type in the Bump ID number (found on the back of the device) and sign up. You will need to charge your Bump Device at the end of every day, use the supplied USB charging lead. Any USB adapter will be suitable.
D – Cleaning D.1. Cleaning Overview For the intended environments of use and limited potential for user interaction, it is not expected for the Device to become heavily soiled in use. Before cleaning, remove the electrical supply and note there are reasonable (<3mm) openings in the rear of the unit. During cleaning avoid ingress with the cloth or cleaning agents used. Using a lint-free, non-abrasive cloth, to wipe the surface dust off. Move the cloth in slow, circular motions.
E - Support The Bump Device has been designed to be as simple as possible to install and operate with a minimum of technical support. All data pertinent to logging onto the website is present within this manual. Should an issue arise, please attempt to resolve using the fault-finding table on the website. the Bump Device product. Please have ready, the product serial number (found on the rating plate) and the detail of any Hub on screen messages which will assist with the fault-finding process.
EC DECLARATION OF CONFORMITY Name of Manufacturer: Tharsus Address: Coniston Road Blyth Northumberland NE24 4RF United Kingdom Description of product: RF Proximity Device Model No: Bump This declaration of conformity is issued under the sole responsibility of the manufacturer. The equipment described above described above is in conformity with the EU Radio Equipment Directive 2014/53/EU by the application of the following standards: EN 300 328 V2.2.2 EN 302 065-2 V2.1.
EC DECLARATION OF CONFORMITY Name of Manufacturer: Tharsus Address: Coniston Road Blyth Northumberland NE24 4RF United Kingdom Description of product: RF Proximity Device Model No: Bump This declaration of conformity is issued under the sole responsibility of the manufacturer. The equipment described above described above is in conformity with the • Restriction of Use of Hazardous Substances (RoHS2) Directive 2011/65/EU by the application standard EN IEC 63000:2018.
