OWNER'S MANUAL -dB 0 0 0 -dB 0 0 0 -dB 0 0 0 0 0 TSA4-700 -dB 0 TSA1400 Fault Clip -5 -10 -15 -20 Signal CH-A CH-B Power -dB 0 0 0 0 0 POWER -dB 0 TSA2200 Fault Clip -5 -10 -15 -20 Signal CH-A CH-B Power -dB 0 0 0 0 0 POWER -dB 0 TSA4-700 TSA1400 TSA2200
PRECAUTIONS WARNING INSTALLATION Connect this unit's power cord only to an AC outlet of the type stated in this ow -ner's Manual or as marked on the unit. Failure to do so is a fire and electrical shock hazard. Do not allow water to enter this unit or allow the unit to become wet. Fire or elec -trical shock may result. Do not place a container with liquid or small metal objects on top of this unit Liquid. or metal ojects inside this unit are a fire and electrical shock hazard.
CAUTION Installation Keep this unit away from the following locations: - Locations exposed to oil splashes or steam, such as near cooking stoves, humidifiers, etc. - Unstable surfaces, such as a wobbly table or slope. - Locations subject to excessive heat, such as inside a car with all the windows Closed, or places that receive direct sunlight. - Locations subjec to excessive humidity or or dust accumulation. Do not place the power cord close to a heater. It may melt, causing fire or electrical shock.
Front Panel -dB 0 0 0 -dB 0 0 0 -dB 0 0 0 0 0 TSA4-700 -dB 0 Power switch Press to toggle the power on or off. POWER Fault LED Fault Lights up red to indicate that protection is in effect. Specifically, lights up if the heat sink overheats, or if a DC voltage is detected at the amplifier outputs. Also lights up for about Three seconds at time of power-on, as the amp gets ready to operate. To provide protection, the unit will not output any sound from the speakers while this indicator is lit up.
Rear panel WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE EQUIPMENT TO RAIN OR MOISTURE! WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE EQUIPMENT TO RAIN OR MOISTURE! Mains Socket Please, make sure to check whether the voltage selector shows the correct mains voltage that matches the local mains supply at the installation site. An appropriate mains cord is included in the package.
Rear panel LF- connection cords Choosing high-quality balanced cables( two conductors for the audio signal plus sepearate shielding mesh) with XLR-type connectors is recommended for LF-signal connection. Although connecting unbalanced cables to the power amplifier inputs is possible as well, using balanced cables is always preferable. A great number of today,s audio appliances employ balanced outputs.
14 335 21 Dimensions 75 88 430 483 465 483 Unit: mm 06
Current Draw Table (in Amperes) Model Load 1/8 Power (pink noise) 1/3 Power (pink noise) Full Power (sine) TSA1400 (2x)8 Ohms 1.93A/330W 4.4A/734W 7.74A/1400W (2x)4 Ohms 2.86A/480W 6.9A/1200W 12.2A/2300W (2x)2 Ohms 4.1A/700W 7.2A/1313W 17.3A/3345W 8 Ohms bridged 3.0A/500W 6.9A/1200W 12.4A2300W 4 Ohms bridged 5.4A/984W 14.2A/2690W 17.2A/3310W (2x)8 Ohms 1.69A/260W 2.73A/400W 9.5A/1700W (2x)4 Ohms 4.0A/680W 6.5A/1180W 14.97A/2800W (2x)2 Ohms 5.0A/850W 9.
Disposal Do not dispose of the device at the end of his operating life in your normal domestic waste. This device is subject to the European Guidelines 2002/96/EC. Have the product disposed of by a professional disposal company of by your communal disposal facility. Observe the currently applicable regulations. In case of doubt contact your disposal facility. Dispose of packaging materials in an environmentally responsible manner. Contact: Musikhaus Thomann Treppendorf 30 96138 Burgebrach Germany www.
