FLUSH MOUNT UNASSEMBLED KIT ASSEMBLY INSTRUCTIONS Looking for an installation video? Scan this code to go directly to our door assembly support page and view the installation video. https://www.themurphydoor.com/assembly-video/ 888-458-5911 MurphyDoor.
Parts List BOOKCASE A Top Long Side Short Side Bottom Bottom (Double Thick) Back Top D (6) #6 x 1.
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY 1 Assemble Face Frame Short Side GLUE Long Side D G (12) Dowel holes toward bottom Top Dowel holes toward top Middle Botto m Dowel holes toward top t Screw Pocke D (6) G Dowel Hole NOTE: Please verify dowel orientation to ensure that they are not installed upside down.
3 Set Shelves With the front of the bookcase laying flat on the floor, use a rubber mallet and a small piece of wood to tap on each side until it is flush with the front of the bookcase. This will ensure that the back piece is able to slide completely into place. Note: The small piece of wood is used to prevent denting or damage to your shelves when setting in place. Back Top t Fron Lon gS ide k Bac m tto Bo Sho rt S ide 4 The shelves should be flush with the front of the bookcase when set properly.
Fastening Face Frame Make sure that all dowel holes are facing the front of the door. G(6) Top Lon g Sid e Bo tto m NOTE: Although not required, you may use some small finish nails in addition to the glue to help secure the face frame. Sho rt Sid e 6 Hinge Templates NOTICE: HINGE TEMPLATES ARE NEEDED FOR HARDWOODS ONLY UPPER JAMB A Place the template for your desired swing configuration onto the upper jamb. Drill the spots where the screws for the hinges will be located.
B Fasten hinge to upper jamb FRENCH DOOR You will need to repeat the same process as above for the left and right sides of the upper jamb. Upper Jamb (French Door) Upper Jamb (French Door) C Rotate upper jamb 180 degrees so the hinge is on the underside of the upper jamb 180˚ Top of Jamb Hinge is now on the underside of the upper jamb FRENCH DOOR You will need to repeat the same process as above for the upper jamb of the french door.
B Fasten hinge to lower jamb (threshold) FRENCH DOOR You will need to repeat the same process as above for the left and right sides of the lower jamb (threshold) Lower Jamb (Threshold) Lower Jamb (Threshold) 7 Assemble Jamb FRENCH DOOR A(8) The jamb assembly for the French Door, is the exact same process as the Flush Mount door. The only difference is the length of the upper jamb and lower jamb (threshold). The Lower Jamb (Threshold) is wider than the rest of the jamb.
Out-Swing Hinges LEFT HINGE RIGHT HINGE OUT-SWING OUT-SWING Placing Pin in Upper Hinge 1) Push in button on end of pin 2) Insert pin through hinge plates 3) Release button after pin has cleared both hinge plates 4) Ball bearings will expand to secure pin in place These extra pre-drilled holes are only used for in-swing hinge configuration.
8 In-Swing Hinges LEFT HINGE RIGHT HINGE IN-SWING IN-SWING Top of Door Top of Door Front Front B B Pre-drilled pattern with hinge pin pass-through hole are only used for out-swing hinge configuration. B B Jamb Bottom Jamb Bottom Front Front (Threshold) (Threshold) These extra pre-drilled holes are only used for out-swing hinge configuration. 888-458-5911 MurphyDoor.
DOOR BOTTOM Hinges on Left DOOR FRONT / FACE FRAME DOOR SIDE OUT SWING VIEW OF DOOR BOTTOM IN SWING DOOR BACK NOTICE: Due to variations in individual printer settings we cannot guarantee that the printed template will be scaled properly. Please use the included measurements to verify proper placement. 888-458-5911 MurphyDoor.
DOOR BOTTOM Hinges on Right DOOR FRONT / FACE FRAME DOOR SIDE OUT SWING VIEW OF DOOR BOTTOM IN SWING DOOR BACK NOTICE: Due to variations in individual printer settings we cannot guarantee that the printed template will be scaled properly. Please use the included measurements to verify proper placement. 888-458-5911 MurphyDoor.
UPPER JAMB HINGE TEMPLATE Hinges on Right NOTICE: Due to variations in individual printer settings we cannot guarantee that the printed template will be scaled properly. Please use the included measurements to verify proper placement. UPPER JAMB HINGE TEMPLATE IN-SWING 4” PL AC E IN FR O N T CO RN ER OUT-SWING NOTE: After attaching the hinge to the upper jamb, before assembling the jamb, you must flip it 180 degrees so that the hinge piece is now on the underside of the upper jamb.
UPPER JAMB HINGE TEMPLATE Hinges on Left NOTICE: Due to variations in individual printer settings we cannot guarantee that the printed template will be scaled properly. Please use the included measurements to verify proper placement. UPPER JAMB HINGE TEMPLATE IN-SWING 4” OUT-SWING E AC PL IN T N O FR ER RN CO NOTE: After attaching the hinge to the upper jamb, before assembling the jamb, you must flip it 180 degrees so that the hinge piece is now on the underside of the upper jamb.
THRESHOLD HINGE TEMPLATE Hinges on Right NOTICE: Due to variations in individual printer settings we cannot guarantee that the printed template will be scaled properly. Please use the included measurements to verify proper placement. THRESHOLD HINGE TEMPLATE IN-SWING 4” OUT-SWING E AC PL IN T N O FR ER RN CO 888-458-5911 MurphyDoor.
THRESHOLD HINGE TEMPLATE Hinges on Left NOTICE: Due to variations in individual printer settings we cannot guarantee that the printed template will be scaled properly. Please use the included measurements to verify proper placement. THRESHOLD HINGE TEMPLATE IN-SWING PL AC E IN FR O N T CO RN ER OUT-SWING 888-458-5911 MurphyDoor.
Ogden Headquarters 2541 Rulon White Blvd Ogden, UT 84404 888-458-5911 Kentucky Distribution Center & Showroom 2320 Fortune Dr. #180 Lexington, KY 40509 FMAM-1.7.3-20170706 MurphyDoor.
