Instructions / Assembly
Trina ALLMAX
PANEL
INSTALLATION MANUAL
1. DISCLAIMER OF LIABILITY
•
The installation, handling and use of Trina Solar crystalline modules are
beyond company control. Trina Solar does not assume any responsibility
for loss, damage, injury or expense resulting from the improper
installation, handling, use or maintenance.
•
Trina Solar assumes no responsibility for any infringement of patents or
other rights of third parties that may result from use of the module. No
license is granted by implication or under any patent or patent
•
Specifications included in this manual are subject to change without prior
notice.
2. SAFETY PRECAUTIONS
•
Potentially lethal DC voltages can be generated whenever PV Modules are
exposed to a light source, therefore, avoid contact with electrically act
parts and be sure to isolate live circuits before attempting to make or
break any connections.
•
Only authorized and trained personnel should have access or perform
work on the modules or solar system, always wearing rubber gloves and
boots with maximum
working voltage not lower than 1000V DC (For TSM
PE14A.**, not lower than 1500V DC).
•
When working on electrical connections, remove all metallic jewelry, use properly insulated tools and
wear appropriate personal protective equipment to reduce
•
Do NOT stand or step on, damage or scratch the front or backside surfaces of the module.
•
Broken modules cannot be repaired and contact with any module surface or frame can lead to
electrical shock. Do NOT use a module with
•
Do NOT disassemble the modules or remove any part of the module.
•
Protect the electrical plug contacts against corrosion and soiling. Make sure that all connectors are
corrosion free and clean before making the connection.
•
Do NOT install or handle modules when they are wet or during periods of high wind.
•
Ensure that all connections are securely made with no gap between the contacts. Any gap can result in
electrical arcing that can cause a fire hazard and/or an electric sho
•
Make sure that the polarity of each module or a string is not reversed considering the rest of the
modules or strings.
•
Do NOT artificially concentrate sunlight on these solar modules.
•
Trina Solar modules are certified for operating in Application
1000V DC (For TSM-
PE05A.**, PE14A.**, below 1500V DC). This maximum voltage should not be
exceeded at any time and, as the voltage of the module increases, above data sheet values, at operating
temperatures below 25°
C, then these need to be taken into account when designing a PV system.
•
Maximum system voltage must not exceed 1000V DC when UL 1000V products (TSM
used.
•
Maximum system voltage must not exceed 1500V DC when UL 1500V products (TSM
used.
•
Do NOT use water to extinguish fires of an electrical origin.
SP-1000
The Solar PaQ
Trina ALLMAX
M Plus 60 Cell 295 watt
UPC: 861150002609
INSTALLATION MANUAL
The installation, handling and use of Trina Solar crystalline modules are
beyond company control. Trina Solar does not assume any responsibility
for loss, damage, injury or expense resulting from the improper
installation, handling, use or maintenance.
Trina Solar assumes no responsibility for any infringement of patents or
other rights of third parties that may result from use of the module. No
license is granted by implication or under any patent or patent
rights.
Specifications included in this manual are subject to change without prior
Potentially lethal DC voltages can be generated whenever PV Modules are
exposed to a light source, therefore, avoid contact with electrically act
ive
parts and be sure to isolate live circuits before attempting to make or
Only authorized and trained personnel should have access or perform
work on the modules or solar system, always wearing rubber gloves and
working voltage not lower than 1000V DC (For TSM
-
PE05A.**,
PE14A.**, not lower than 1500V DC).
When working on electrical connections, remove all metallic jewelry, use properly insulated tools and
wear appropriate personal protective equipment to reduce
the risk of electric shock.
Do NOT stand or step on, damage or scratch the front or backside surfaces of the module.
Broken modules cannot be repaired and contact with any module surface or frame can lead to
electrical shock. Do NOT use a module with
broken glass or torn substrate.
Do NOT disassemble the modules or remove any part of the module.
Protect the electrical plug contacts against corrosion and soiling. Make sure that all connectors are
corrosion free and clean before making the connection.
Do NOT install or handle modules when they are wet or during periods of high wind.
Ensure that all connections are securely made with no gap between the contacts. Any gap can result in
electrical arcing that can cause a fire hazard and/or an electric sho
ck.
Make sure that the polarity of each module or a string is not reversed considering the rest of the
Do NOT artificially concentrate sunlight on these solar modules.
Trina Solar modules are certified for operating in Application
Class A installations at voltages below
PE05A.**, PE14A.**, below 1500V DC). This maximum voltage should not be
exceeded at any time and, as the voltage of the module increases, above data sheet values, at operating
C, then these need to be taken into account when designing a PV system.
Maximum system voltage must not exceed 1000V DC when UL 1000V products (TSM
-
****D*. **) are
Maximum system voltage must not exceed 1500V DC when UL 1500V products (TSM
-
****E*.
Do NOT use water to extinguish fires of an electrical origin.
PE05A.**,
When working on electrical connections, remove all metallic jewelry, use properly insulated tools and
Do NOT stand or step on, damage or scratch the front or backside surfaces of the module.
Broken modules cannot be repaired and contact with any module surface or frame can lead to
Protect the electrical plug contacts against corrosion and soiling. Make sure that all connectors are
Ensure that all connections are securely made with no gap between the contacts. Any gap can result in
Make sure that the polarity of each module or a string is not reversed considering the rest of the
Class A installations at voltages below
PE05A.**, PE14A.**, below 1500V DC). This maximum voltage should not be
exceeded at any time and, as the voltage of the module increases, above data sheet values, at operating
C, then these need to be taken into account when designing a PV system.
****D*. **) are
****E*.
**) are