Instructions / Assembly

Trina ALLMAX
• For cUL listed products only:
• Fire class rating: C
•
The fire rating of the module is valid only when mounted in the manner specified in the mechanical
mounting instructions.
•
The module is considered to be in compliance with UL1703 only when the module is mounted in the
manner specified by the mounting instructions.
•
A module with exposed conductive parts is considered to be in compliance with UL1703 only when it
electrically grounded in accordance with the instructions and the requirements of the National Electrical
Code.
•
Any module without a frame (laminate) shall not be considered to comply with the requirements of
UL1703 unless
the module is mounted with h
ardware that has been tested and evaluated with the module under this
standard or by a field Inspection certifying that the installed module complies with the requirements of
UL1703.
3. UNPACKING AND STORAGE
•
At time of receipt, verify that the product delivered is in fact the product ordered. The product name,
subname, and serial number of each laminate are clearly marked on the outside of each packing box.
•
Leave the product in its original packing box until
•
Store packing boxes in a clean, dry area with relative humidity below 85% and ambient temperatures
between -20°C and 50°C.
•
Do NOT stack more than the maximum amount of allowable pallets on top of each other.
• At the installation
site, take care to keep modules and particular their electrical contacts clean and dry
before installation. If connector cables are left in damp conditions then the contacts may corrode. Any
module with corroded contacts should not be used.
• If pallets ar
e stored temporarily outside then place a protective covering over the pallet to protect it
from direct weathering and do not stack more than 1 pallet high.
•
Two people are required to unpack the modules from the packing box, when handling modules always
use both hands.
•
Protect the module edges for temporary storage outside the pallet.
• Do NOT use a knife to cut the zip-
ties, but use wire cutting pliers.
•
Do NOT place modules directly on top of each other.
SP-1000
The Solar PaQ
Trina ALLMAX
M Plus 60 Cell 295 watt
UPC: 861150002609
The fire rating of the module is valid only when mounted in the manner specified in the mechanical
The module is considered to be in compliance with UL1703 only when the module is mounted in the
manner specified by the mounting instructions.
A module with exposed conductive parts is considered to be in compliance with UL1703 only when it
electrically grounded in accordance with the instructions and the requirements of the National Electrical
Any module without a frame (laminate) shall not be considered to comply with the requirements of
ardware that has been tested and evaluated with the module under this
standard or by a field Inspection certifying that the installed module complies with the requirements of
At time of receipt, verify that the product delivered is in fact the product ordered. The product name,
subname, and serial number of each laminate are clearly marked on the outside of each packing box.
Leave the product in its original packing box until
you are ready to install.
Store packing boxes in a clean, dry area with relative humidity below 85% and ambient temperatures
Do NOT stack more than the maximum amount of allowable pallets on top of each other.
site, take care to keep modules and particular their electrical contacts clean and dry
before installation. If connector cables are left in damp conditions then the contacts may corrode. Any
module with corroded contacts should not be used.
e stored temporarily outside then place a protective covering over the pallet to protect it
from direct weathering and do not stack more than 1 pallet high.
Two people are required to unpack the modules from the packing box, when handling modules always
Protect the module edges for temporary storage outside the pallet.
ties, but use wire cutting pliers.
Do NOT place modules directly on top of each other.
The fire rating of the module is valid only when mounted in the manner specified in the mechanical
The module is considered to be in compliance with UL1703 only when the module is mounted in the
A module with exposed conductive parts is considered to be in compliance with UL1703 only when it
is
electrically grounded in accordance with the instructions and the requirements of the National Electrical
Any module without a frame (laminate) shall not be considered to comply with the requirements of
ardware that has been tested and evaluated with the module under this
standard or by a field Inspection certifying that the installed module complies with the requirements of
At time of receipt, verify that the product delivered is in fact the product ordered. The product name,
subname, and serial number of each laminate are clearly marked on the outside of each packing box.
Store packing boxes in a clean, dry area with relative humidity below 85% and ambient temperatures
Do NOT stack more than the maximum amount of allowable pallets on top of each other.
site, take care to keep modules and particular their electrical contacts clean and dry
before installation. If connector cables are left in damp conditions then the contacts may corrode. Any
e stored temporarily outside then place a protective covering over the pallet to protect it
Two people are required to unpack the modules from the packing box, when handling modules always