Instructions / Assembly
Trina ALLMAX
3.1 PRODUCT IDENTIFICATION
Each individual module has a unique serial number laminated behind the glass and another
permanently attached to the back
in an installation for your future records.
4. ENVIRONMENTAL C
ONSIDERATIONS
4.1 CLIMATE CONDITIONS
Trina Solar Crystalline series modules may be installed in the following conditions for more than 25
years. In addition to the required IEC certification, Trina Solar products have also been tested to verify
resistance to ammonia fumes that may be present around barns sheltering cattle, as well as suitability
for installation in humid (coastal) areas and areas of high sand storms.
Environment
• Ambient temperature: -
40°C to 50°C
• Operating temperature: -
40°
• Storage temperature: -
20°C to +50°C
• Humidity:
< 85RH%
•
Mechanical Load Pressure*:5400Pa (550 Kg/m²) Max from the front side (snow) & 2400Pa (wind)
from the rear (Except Installation Method C: Mounting with
& 2400Pa (wind)
max under UL1703 standard)
*Notes:
-
The modules have been evaluated by TUV according to IEC61215 for a maximum positive or negative
design loading of below 550Kg/m² (5400Pa),by UL according to UL 1703, below 30lbs.ft
-The
mechanical load bearing is dependent upon the mounting methods used and failure to follow the
instructions of this manual may result in different capabilities to withstand snow and wind loads.
-
The system installer must ensure that the installation method
any local codes and regulations.
5. SITE SELECTION
•
Trina Solar Modules can be mounted in landscape or portrait orientation however the impact of dirt
shading the solar cells can be minimized by orienting the product
•
Solar module is recommended to be installed at an optimized tilt angle to maximize the energy output.
It is roughly equal to the latitude of the project site as a rule of thumb, facing to equator. But always to
design based on local
situations to find out the optimum one.
•
When installing solar modules on a roof always leave a safe working area between the edge of the roof
and the external edge of the solar array.
•
In case of residential installations on the ground, modules shall be i
e.g. using fence.
•
Position the modules to minimize the chances of shading at any time of the day.
•
Do not install PV modules in a location where they will be immersed in water or continually exposed to
water from a sp
rinkler or fountain, etc.
•
Avoid using a mounting method that will block the drainage holes in the module frame.
SP-1000
The Solar PaQ
Trina ALLMAX
M Plus 60 Cell 295 watt
UPC: 861150002609
Each individual module has a unique serial number laminated behind the glass and another
permanently attached to the back
-
sheet of the module on the product sticker. Note all serial numbers
in an installation for your future records.
ONSIDERATIONS
Trina Solar Crystalline series modules may be installed in the following conditions for more than 25
years. In addition to the required IEC certification, Trina Solar products have also been tested to verify
resistance to ammonia fumes that may be present around barns sheltering cattle, as well as suitability
for installation in humid (coastal) areas and areas of high sand storms.
40°C to 50°C
40°
C to +85°C
20°C to +50°C
< 85RH%
Mechanical Load Pressure*:5400Pa (550 Kg/m²) Max from the front side (snow) & 2400Pa (wind)
from the rear (Except Installation Method C: Mounting with
Single-
axis Tracking System
The modules have been evaluated by TUV according to IEC61215 for a maximum positive or negative
design loading of below 550Kg/m² (5400Pa),by UL according to UL 1703, below 30lbs.ft
mechanical load bearing is dependent upon the mounting methods used and failure to follow the
instructions of this manual may result in different capabilities to withstand snow and wind loads.
The system installer must ensure that the installation method
s used meet these requirements and
Trina Solar Modules can be mounted in landscape or portrait orientation however the impact of dirt
shading the solar cells can be minimized by orienting the product
in landscape.
Solar module is recommended to be installed at an optimized tilt angle to maximize the energy output.
It is roughly equal to the latitude of the project site as a rule of thumb, facing to equator. But always to
situations to find out the optimum one.
When installing solar modules on a roof always leave a safe working area between the edge of the roof
and the external edge of the solar array.
In case of residential installations on the ground, modules shall be i
nstalled following local regulations,
Position the modules to minimize the chances of shading at any time of the day.
Do not install PV modules in a location where they will be immersed in water or continually exposed to
rinkler or fountain, etc.
Avoid using a mounting method that will block the drainage holes in the module frame.
Each individual module has a unique serial number laminated behind the glass and another
sheet of the module on the product sticker. Note all serial numbers
Trina Solar Crystalline series modules may be installed in the following conditions for more than 25
years. In addition to the required IEC certification, Trina Solar products have also been tested to verify
resistance to ammonia fumes that may be present around barns sheltering cattle, as well as suitability
Mechanical Load Pressure*:5400Pa (550 Kg/m²) Max from the front side (snow) & 2400Pa (wind)
axis Tracking System
- 2400Pa (snow)
The modules have been evaluated by TUV according to IEC61215 for a maximum positive or negative
design loading of below 550Kg/m² (5400Pa),by UL according to UL 1703, below 30lbs.ft
2
.
mechanical load bearing is dependent upon the mounting methods used and failure to follow the
instructions of this manual may result in different capabilities to withstand snow and wind loads.
s used meet these requirements and
Trina Solar Modules can be mounted in landscape or portrait orientation however the impact of dirt
Solar module is recommended to be installed at an optimized tilt angle to maximize the energy output.
It is roughly equal to the latitude of the project site as a rule of thumb, facing to equator. But always to
When installing solar modules on a roof always leave a safe working area between the edge of the roof
nstalled following local regulations,
Do not install PV modules in a location where they will be immersed in water or continually exposed to
Avoid using a mounting method that will block the drainage holes in the module frame.