Installation Guide

Application data
Time before grouting oor application:
● with normal-setting adhesive: 24 hours
● with fast-setting adhesive: 4 hours
● with mortar: 7-10 days
Wall application
● with normal-setting adhesive: 24 hours
● with fast-setting adhesive: 4 hours
● with mortar: 2-3 days
Mixing ratios:
Component A: 93.7 parts by weight
Component B: 6.3 parts by weight
The two components are pre-measured in their respective packaging
Mix consistency:
Thixotropic paste
Specic gravity of mix
1.55 kg/l
Performance
Initial shear adhesion strength (EN 12003): ≥ 2 N/mm
2
Shear adhesion strength after water immersion (EN 12003):
≥ 2 N/mm
2
Shear adhesion strength after thermal shock (EN 12003): ≥ 2
N/mm
2
Open time (EN 1346): ≥ 0.5 N/mm
2
after 20 minutes
Determination of slip (EN 1308): ≤ 0.5 mm
Resistance to abrasion (EN 12808-2): ≤ 250 mm
3
Flexural tensile strength after 28 days
at standard conditions (EN 12808-3): ≥ 30 N/mm
2
Compressive strength after 28 days
at standard conditions (EN 12808-3): ≥ 45 N/mm
2
Shrinkage (EN 12808-4): ≤ 1.5 mm
Water absorption after 4 hours (EN 12808-5): ≤ 0,1 g
Working temperature: From - 20°C to +100°C
Mixture life:
About 1 hour at T = +23°C / 73,4°F
Application temperatures allowed:
From +10°C to +30°C / From +50°F to 86°F
Recommended application temperature:
From +18°C to +23°C / From + 64,4°F to 73,4°F
Set to light foot trac:
24 hours at T = +23°C / 73,4°F
Ready for use:
5 days at T = +23°C / 73,4°F
Joint width:
From 1 to 15 mm (0,039 - 0,59 in)
EXCLUSIVE DISTRIBUTOR FOR USA
Tile Doctor
www.TileDoctor.com
877-TileDoc (845-3362)
Made In Italy
Application
STARLIKE EVO
1 Empty completely all the contents of the catalyst (B) onto the paste (A).
2 Special finishes: pour the additive onto the paste and mix slowly.
3
Mix at slow speed using an electric drill equipped with mixing paddle. Scrape the walls of the bucket to eliminate all parts of non-catalysed
product.
4
The joints must be dry. Introduce the mortar into the joints using the suitable green rubber float (Art. 946GR) spreading diagonally across the
joints. Remove the excess product.
5
The grout must be cleaned while the product is still wet. Sprinkle clean water. Initial cleaning using a moistened white felt (art. 109/GBNC)
making circular movements. Ensure no water enters the joints.
6 Now perform a second cleaning with a rigid cellulose sponge (art. 128G0001).
7
Any stains of the transparent product can be removed after 24 hours or anyway after the gap has hardened. Use Haze Remover.
Spread Haze Remover with the white felt.
8 Leave on for 15-30 minutes. Scrub the surface with the white felt.
9 Rinse with clean water. Dry immediately with a clean cloth and do not wait for the evaporation of the rinse water.
AA
BB
Litonet EVOLitonet EVO
Litonet Gel EVOLitonet Gel EVO