INSTRUCTION MANUAL ST - R E A D Y- T Specifications Wing Span Wing Area Flying Weight Fuselage Length 63 in / 1600 mm 1420 sq in / 91.6 sq dm 13-15 lbs / 5900-6810 g 66.5 in / 1690 mm * Specifications are subject to change without notice.* Warning !This model is not a toy. It is designed for maximum performance. Please seek advice if one is not familiar with this kind of engine powered precision model. Operating this model without prior preparation may cause injuries.
INDEX BEFORE YOU BEGIN P. 1 PARTS LIST P. 2 ASSEMBLY P. 3 - 14 SAFETY PRECAUTIONS P. 14 BEFORE YOU BEGIN 1 Read through the manual before you begin, so you will have an overall idea of what to do. 2 Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement.
Parts List 1.MAIN WING(Upper Wing) -- 1 pair MAIN WING(Lower Wing)-- 1 pair METAL HINGES -- 28 pcs 2.SERVO MOUNTING PANEL ( For Aileron Servo ) -- 1 pair HEAVY DUTY SERVO HORN PL4120350 -- 2 sets SCREW PM4x50mm -- 2 pcs SCREW PWA2x12mm -- 8 pcs M4 NYLON INSERT LOCK NUT -- 2 pcs HEAVY DUTY HORN BRACKET PL4112400 -- 2 sets HEAVY DUTY CLEVIS PL412200 -- 4 sets SWIVEL CLEVIS HORN FAIRING PL4610010 -- 2 sets PUSHROD 2.5x70mm w/Threads(For Aileron) -- 2 pcs 3.
1 Main Wing Replace CA hinges by metal hinges. Glue the metal hinges to wing and aileron by epoxy. Main Wing (Upper) Main Wing (Lower) Aileron Servo Lead Aileron Servo Lead Bottom View Bottom View 2 Aileron Servo (Upper Wing) PM4x50mm Screw PM 2 x 12 mm PL4120350 M2 Nut 2 M4 Nylon Insert Lock Nut 2 1.5mm Heavy Duty Horn Bracket PM2x 8mm M4 Nylon Insert Lock Nut Heavy Duty Clevis M2 Nut Hea vy Dut y Cle vis M2 Nut PM2x8mm Pushrod PM4 x 50mm 2.5x70mm PA1.
3 Aileron Servo (Lower Wing) PM4x50mm Screw 2 M4 Nylon Insert Lock Nut 2 Similar installation as upper wing. 1.5mm Bottom View 4 Stabilizer & Elevator Wire Ø3x186mm PWA3 x 12mm Screw 2 PWA3x12mm 2mm 130m m 40mm Bottom View M3 x 6mm Set Screw M3 x 6mm Set Screw PWA3 x 12mm Stabilizer Tube Ø14.5x319mm Bottom View 2mm Replace CA hinges by metal hinges. Glue the metal hinges to stabilizer and elevator by epoxy. A A Bottom View A=A P.
5 Vertical Fin & Rudder B B' B=B' Replace CA hinges by metal hinges. Glue the metal hinges to vertical and rudder by epoxy. Completed 6 Tail Landing Gear PA3 x 12mm Screw 2 2.6mm Collar 1.5mm 1 PA3 x 12mm 2.5mm Rubber Tail Wheel Ø30mm 2.6mm Collar M3 x 3mm Set Screw Bottom View P.
Engine Box PM3x13mm F8 (3x90x361.5mm) F48 F8' (3x90x366.5mm) Screw 8 M3 Nylon Insert Lock Nut 8 d3xD7mm Washer 16 F49 F26 F26A Please note right thrust angle of firewall. d3xD7mm Washer PM3x13mm M3 Nylon Insert Lock Nut Completed Use epoxy to glue all parts together. F53 F49 F48 F8' F9C F9D F9B' F9 2 F53A F9B F9C F26 F8 F9A F26A F9 0 F8B P.
Wing Cabane PM3x 13mm Screw 5 PM3x 16mm Screw 1 d3xD7mm Washer d3xD7mm Washer 12 M3 Nylon Inert Lock M3 Nylon Inert Lock Nut Nut 6 d3xD7mm Washer PM3x13mm M3 Nylon Inert Lock Nut d3xD7mm Washer d3xD7mm Washer 1A 2A 1A d3xD7mm Washer F18B 2A 1A d3xD7mm Washer F18C PM3x16mm 2B 2B PM3x13mm 9 Main Landing Gear Ø4x54mm Axle Shaft 2 M5x16mm Socket Head Screw M8 Nylon Inert Lock Nut M5x16mm SOCKET HEAD SCREW Ø4x54mm 3mm Set Screw 4 PA3x12mm Screw 4 4.1mm PA3x12mm Collar 4.
10 Rudder Pullwire M 4 x 80mm Press down the center 1/3 portion Heavy Duty Horn Bracket M 4 x 80mm Screw 1 M4 Nylon Insert Lock Nut 2 M4 Nylon Insert Lock Nut PA1.7x8mm M2 Nut PM2x8mm Heavy Duty Clevis Eye Screw M2.5x8x25mm Copper Tube 165mm 28mm Bottom View Bottom View 11 Elevator Pushrod PM 4 x 50mm Screw 1mm 2 M4 Nylon Insert Lock Nut 2 PL4120350 M2 Nut PM2x8mm Heavy Duty Clevis Heavy Duty Horn Bracket PA1.
Make sure that tongue on front of fuel tank hold down plate slides into slot of F2. 12 Fuel Tank PM3x12mm Screw 2 d3xD7mm Washer 2 Plywood 3x95x281mm (F2A) F2 Cable Tie Sponge Plywood Plywood 3x95x281mm 3x95x281mm (F2A) Cable Tie Sponge to cushion fuel tank. d3xD7mm Washer Fuel Tank 650cc PM3x12mm Tongue 13 Engine Center line of firewall Plywood 3x120x129.5mm (F8A) M6 4.8mm Blind Nut 4 31.
14 Radio Equiment Copper Tube Press down the center 1/3 portion Install and arrange the servo as shown in the diagram. Rudder Pullwire Ø1x800mm Eye Screw M2.5x8x25mm 3 15 Main Wing (Lower) PM3x16mm Screw PA3x16mm Screw 1 1 d3 x D7mm Washer 2 Heavy Duty Clevis M2 Nut Eye Screw PM2x8mm Heavy Duty Clevis Front Sponge HEAVY DUTY SERVO HORN PL4120800 Rudder Servo Step1.Insert aluminum wing tube (Ø16x806mm)with the pre-drilled Wing Tube hole end into the right wing(lower).
3 16 Main Wing (Upper) PM3x16mm Screw PA3x16mm Screw Step1.Insert aluminum wing tube (Ø16x645mm)with the pre-drilled hole end into the right wing(upper). Align the lines marked at the wing root and wing tube,then apply the PM3X16mm machine screw through the pre-drilled hole on top of the wing.(please confirm the alignment of the hole by putting a 2.
17 Outer Wing Cabanes PM3x18mm Screw 8 d3 x D7mm Washer 16 M3 Nylon Insert Lock Nut 8 d3 x D7mm Washer Plywood 3x330x388mm d3 x D7mm Washer PM3x18mm Outer wing cabane should fit to the outside of outer wing cabane mounts. M3 Nylon Insert Lock Nut 3mm 18 Canopy With the wing incidence angle template still in place, position the side cabanes, mark and drill the side cabane mounts and fasten with PM3x18mm screw and nut. First insert the grommet to the canopy then apply screw. PWA2.
20 Wing Setting Adjust the wing and fuselage configuration as shown in the diagrams. A A' B' B C C' D' D E F E' G G' F' A=A' B=B' C=C' D=D' E=E' F=F' G=G' A72S1 27% ULTIMATE ENGINE DOWN THRUST ANGLE MAIN WING INCIDENCE ANGLE P.
21 Control Throws Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. Elevator 30mm 30mm Rudder 70mm 70mm Ailerons 25mm 25mm 22 C.G. 135mm 5.3 in. The ideal C.G. position is at center of top wing tube. You can check the C.G. by hanging the plane with wire around the top wing tube. Unscrew the right wing bolt will leave a gap for the wire. In order to obtain the C.G.
LINKAGE CONNECTOR HW7111030 & HW7111060 Drill 2mm hole at servo horn. Insert linkage connector into servo horn. Make sure shoulder of screw is cleared from servo horn. Add washer to reduce play if necessary. Shoulder Tighten up the round nut against the shoulder. Apply CA or permanent thread locker. After fastening the round nut, make sure that the linkage connector can rotate freely.
