Operation Manual

ManualsBrandsTheben ManualsBackupTheLuxa S150 WH 1010500

theLuxa S150 WH 1010500

theLuxa S150 BK 1010501

theLuxa S180 WH 1010505

theLuxa S180 BK 1010506

309691 01

Motion detector

1. Essential safety instructions

Danger of death through electric shock or fire!

 Installation should only be carried out by a pro-

fessional electrician!

WARNING

•

The device conforms with EN 60669-2-1 when correctly

installed

•

IP 55 in accordance with EN 60529

Designated use

•

Motion detector for automatic lighting control dependent

on presence and brightness

•

Suitable for installation on external walls

•

Suitable for entrances, garages, gardens, corridors, parks,

etc.

•

Only intended for installation outside of arm‘s reach

Summary of content (13 pages)

PAGE 1
309691 01 EN Motion detector theLuxa S150 WH theLuxa S150 BK 1010500 1010501 theLuxa S180 WH theLuxa S180 BK 1010505 1010506 1.
PAGE 2
Disposal Dispose of the motion detector in an environmentally sound manner (electronic waste) 2. Description Motion detector with sensor head 2 potentiometers for setting time (min) and brightness (lux) 3. Connection WARNING Danger of death through electric shock! Disconnect power source! Cover or shield any adjacent live components.
PAGE 3
! The device can be manually activated with a circuit breaker. After releasing the button (return of power) the device switches on (for at least 40 secs or for the time set on the device).
PAGE 4
. Installation If applicable, use optional corner bracket (9070902, 9070903) or spacer frame (9070906, 9070907) for flexible installation as well as cable insertion from side or top/ bottom. 230V Disconnect power source. Make marks for the holes on the wall (with en-closed drill template/base).
PAGE 5
Drill holes. Ø 6 mm 60 mm Feed cable through the seal of the base. Fasten base (and spacer frame) to the wall. Phase brown Neutral conductor Earthing conductor blue Switched phase Neutral conductor Earthing conductor brown blue green/yellow Connect the individual wires to the appropriate terminal. Tighten screws.
PAGE 6
Click! Plug motion detector into base and click in. Connect motion detector to power supply. Dismantling Using the screwdriver, carefully loosen the snap-in hook at the side and pull the device forward.
PAGE 7
Installation instructions As the detector reacts to variations in temperature, avoid the following situations: Do not direct motion detectors at objects with highly reflec- tive surfaces such as mirrors etc. Do not install motion detectors near heat sources such as heating outlets, air conditioning systems, lamps etc. Do not direct the motion detector at objects that turn in the wind such as curtains, large plants etc. Take account of motion direction during test run.
PAGE 8
5 3m m m 12 180° 6m ••Recommended installation height: 2 – 4 m ••Crosswise detection area: 12 m (crosswise to the detector) ••Frontal detection area: 5 m (in front of the detector) ••Detection angle: 150°/180° 5. Direction test and alignment The walk test is used to test the detection range and to restrict it if necessary. Set the potentiometer time (min) to test. The motion detector now only reacts to movement (independent of brightness). Crosswise to the detection area.
PAGE 9
0 2 10 min 30s test 2 sec 2 Sec 20 Test Align motion detector with sensor head The sensor head can be turned by 30° downwards and by 90° to left and right.
PAGE 10
6. Setting The motion detector has two potentiometers underneath for setting the time (min) and brightness (lux). 15 10 100 30s 2 10 min lux 7 test 20 Set brightness (lux) You can set different brightness values (lux) with the potentiometer. If you want to change the preset brightness (15 lux default) Set potentiometer to desired brightness (5 – 1000 lux).
PAGE 11
Set time (min) If the motion detector detects no further movement, it switches off after the set time. If you want to change the preset time (2 min default) Set potentiometer to desired time (0.5 s – 20 min). 2 min test 1 min 10 min 30s 2 20 2 min 30 s 1s test 5 min 10 min 15 min 20 min If you want to use the pulse function (e.g. for a staircase light time switch) Set potentiometer to position . The motion detector is switched on for < 1 s, then off for 9 s.
PAGE 12
••Brightness setting range: 5–1000/∞ lux 5 s – 20 min ••Switching period range: ••Permissible ambient temperature: –25 °C to +45 °C ••Protection class: II ••Protection rating: IP 55 in accordance with EN 60529 ••Switching capacity: 10 A (cos ϕ = 1) 6 A (cos ϕ = 0.6) 3 AX (cos ϕ = 0.3) Min.
PAGE 13
Service address Theben AG Hohenbergstr. 32 72401 Haigerloch GERMANY Phone +49 7474 692-0 Fax +49 7474 692-150 Hotline Phone +49 7474 692-369 Fax +49 7474 692-207 hotline@theben.de Addresses, telephone numbers etc. www.theben.