- Therma-Stor Products Owner's Manual Dehumidifier Phoenix 200 HT

ManualsBrandsTherma-Stor Products Group ManualsHousehold AppliancePhoenix 200 HT

www.thermastor.com • sales@thermastor.comToll-Free 1-800-533-7533

Phoenix 200 HT

PN 4025900

Owner’s Manual — 200 HT LGR Dehumidiﬁer

Installation, Operation and Service Instructions

Read and Save These Instructions

200 HT LGR Dehumidiﬁer

TS-302

The Phoenix 200 HT features LGR (low grain refrigerant) technology. This technology enables the 200 HT to remove more

water and create more grain depression than standard refrigerant dehumidiﬁers.

Combined with this performance, the multiple ducting and the superior high temperature performance makes the Phoenix

200 HT the most effective and versatile drying device made.

The Phoenix 200 HT

LGR Dehumidiﬁer

In-Board Wheels - Reduces outer dimensions for

tighter storage setups and does not catch on

obstructions for easier movement around the jobsite.

Recessed Condensate Hose - Does not catch on

obstructions and allows for dense storage setups by

reducing overall width of the unit.

Increased Capacity - The Phoenix 200 HT removes 5%

more water than the 200 MAX.

Improved High-Ambient Performance - Patent pending

technology allows superior efﬁciency in high-ambient

conditions.

Focused Airﬂow - Patent pending focused outlet directs

air toward the most wet surface.

325 CFM - More processed air speeds drying and

provides superior static pressure for ducting.

More Grain Depression - The driest air from an LGR

gets your jobs drier quicker.

Air Filter - A MERV-11 is standard.

Multiple Ducting Options - 12” intake, 10” exhaust.

Energy Efﬁciency - Draws 7.5 amps.

Skid Plate - Protects the 200 HT from damage while

transporting, loading and unloading.

Speciﬁcations subject to change without notice.

Revised 1/07

PO Box 8680 • Madison, WI 53708

Summary of content (9 pages)

PAGE 1
200 HT LGR Dehumidifier TS-302 PO Box 8680 • Madison, WI 53708 Owner’s Manual — 200 HT LGR Dehumidifier Installation, Operation and Service Instructions Read and Save These Instructions The Phoenix 200 HT features LGR (low grain refrigerant) technology. This technology enables the 200 HT to remove more water and create more grain depression than standard refrigerant dehumidifiers.
PAGE 2
1 Specifications Table of Contents Introduction.................................................................1 1. Specifications.........................................................2 2. Operation..............................................................2 2.1 Transporting . ..................................................2 2.2 Electrical Requirements ...................................2 2.3 Condensate Removal . .....................................2 2.4 Ducting..................................
PAGE 3
2.3 Condensate Removal is directed across the evaporator. This airflow lowers the refrigerant pressure in the condenser and improves dehumidifier efficiency. The relative reduction or slowing of airflow across the evaporator allows more time for the air temperature to be lowered to the dew point, which also increased dehumidifier efficiency. These higher temperatures are often found after the first 24 hours. See Figure 1 for correct grain control magnet position for operating in temperatures above 90°F.
PAGE 4
3 Maintenance the evaporator more quickly and efficiently. See Figure 3 below for correct grain control magnet position and defrost timer for operating in temperatures below 50°F. 3.1 Air Filter The Phoenix 200 HT is equipped with a pleated fabric air filter that must be checked regularly. The standard filter is a MERV-11 high efficiency filter.
PAGE 5
Some dehumidification, blower runs continuously but compressor only runs sporadically. 1. Unit is in defrost cycle. 2. Defrost thermostat defective or loose. 3. Loose connection in compressor circuit. 4. Defective compressor overload. 5. Defective compressor. 6. Defective relay. No dehumidification, blower runs but compressor does not. 1. Bad connection in compressor circuit. 2. Pump safety switch closed. 3. Defective compressor capacitor. 4. Defective compressor overload. 5. Defective compressor. 6.
PAGE 6
Evaporator coil frosted continuously, low dehumidifying capacity. 1. Defrost thermostat loose or defective. 2. Defrost timer incorrectly set or defective. 3. Low refrigerant charge. 4. Dirty air filter or air flow restricted. Compressor runs with power switch OFF. 1. Defective relay. 2. Defective power switch. 4.3 Blower Replacement The motorized impeller has a PSC motor and internal thermal overload protection. If defective, the complete assembly must be replaced. 1. Unplug the power cord. 2.
PAGE 7
5 Options and Accessories 4.7 Relay The contacts of the single pole, single throw relay complete the power circuit to the compressor. The contacts are closed when power is provided to the relay coil via the control circuit. The control circuit includes the power switch, low pressure control, defrost thermostat and timer.
PAGE 8
Service Parts Item Description 1 2 3 4 Air Filter, Pleated, 2 X 16 X 20 1 Cord 1 Front Panel Retaining Nut, 1/4-20 1 Wheel, 8” 2 Wheel Hub Cap 2 Retaining Ring 2 Hub Cap Retaining Washer 2 Coupling Body, 1/4 Tube 1 Foot 2 Defrost Timer 1 Low Pressure Control 1 Filter/Drier 1 Compressor, Carlyle 1 (P/N EAA090111A) Overload, Carlyle Compressor 1 Capillary Tubes 2 Defrost Thermostat 1 Defrost Thermostat Mounting Clip 1 Evaporator Coil 1 Accumulator 1 Top 1 Handle Assembly 1 5 6 7 8 9 10 1
PAGE 9
Phoenix 200 HT Dehumidifier Limited Warranty Warrantor: Therma-Stor LLC PO Box 8680 Madison, WI 53708 Telephone: 1-800-533-7533 Who Is Covered: This warranty extends only to the original end-user of the Phoenix 200 HT dehumidifier, and may not be assigned or transferred.