Manual

ManualsBrandsTherma-Tru ManualsFor HomeSHOP 2 Equipment and Facilities - Book Size

Equipment

and Facilities

Shop 2 2014 (BOOK SIZE) 2.1

SHOP 2 Equipment and Facilities

Equipment �� 2�3

Shop Layout �� 2�6

Summary of content (9 pages)

PAGE 1
SHOP 2 Equipment and Facilities Equipment �� 2.3 Shop Layout �� 2.6 Shop 2 2014 (BOOK SIZE) 2.
PAGE 2
Equipment and Facilities 2.
PAGE 3
Equipment Equipment and Facilities Below is a recommended list of equipment required for a millwork shop. Air Compressor Assembly Tables (see sketches on following pages) Caulking Guns (manual or air-powered) Drill Press (optional) Miter Saw Power Drill Radial-Arm Saw Screw Guns with torque-adjustable clutch Shop Hand Tools - hammer, chisel, etc. Staple Guns (various sizes) Table Saw (sliding table preferred) Special-purpose machinery (ex.
PAGE 4
2.4 2014 (BOOK SIZE) 85” 3/4” Plywood 79” x 35-1/8” DETAIL B NOTE: For longer wearplastic laminate can be added to 3/4” plywood top. 70-1/8” 88” A A 8” 35-1/2” 1-1/2” 3-1/2” 8-7/8” 1-1/2” 4-1/2” 21-1/8” 36-5/8” 10” 1-1/2” DETAIL B 1-1/2” sq. x 70-1/8” long (3 reqd) 41-1/8” SECTION A-A Butt frame head to this block.
PAGE 5
Shop 2 2014 (BOOK SIZE) Floorline 1/4” Masonite or Equivalent 50” 84” DOOR LITE TABLE 16-1/4” 2x4 Construction 42” 32" 10” Equipment Equipment and Facilities 2.
PAGE 6
Equipment and Facilities Shop Layout The following pages show three typical shop layouts recommended by Therma-Tru. They are an “L” and “U” shaped and “In-Line” configuration assembly line. Contact Therma-Tru if you need assistance on how your shop should be configured. 2.
PAGE 7
Shop 2 2014 (BOOK SIZE) Miter Saw Air (90-95 PSI) 220 v (3 Phase) 110 v Supply 35’ Hand Tool Storage Drill Press (optional) Door Prep. Table Door Prep. Parts Racks Door Lite Cutout Template Rack Recommended door unit assembly area for an “L” shaped assembly line. Table Saw Frame Prep. Table Assembled Units Out Frame Parts Racks (Jamb legs vertical) 40’ Components In Overhead Door Compressor Shop Layout Equipment and Facilities 2.
PAGE 8
2.8 2014 (BOOK SIZE) Air (90-95 PSI) 220 v (3 Phase) 110 v Supply 24’ Miter Saw Frame Table Table Saw Door Prep. Table Components In Door Lite Cutout Template Rack Door Prep. Parts Racks Recommended door unit assembly area for a “U” shaped assembly line. Assembled Units Out Frame Prep. Table Frame Parts Racks (Jamb legs vertical) 36’ Misc. Door Prep.
PAGE 9
26’ Shop 2 2014 (BOOK SIZE) Air (90-95 PSI) 220 v (3 Phase) 110 v Supply Components In Door Lite Cutout Door Prep. Table Compressor Table Saw Assembled Units Out Miter Saw Frame Parts Racks (Jamb legs vertical) Frame Prep. Table Frame Parts Racks Recommended door unit assembly area for an “In-Line” assembly line. Door Prep. Parts Racks Template Rack Door Prep. Parts Racks 48’ Shop Layout Equipment and Facilities 2.